Multiquip HS62A manual Cam .The V-belt should remain in tension, Re-attach the cover guard

Page 24

HS62A CUT-OFF SAW — MAINTENANCE

Reversing the Cutting Arm Procedure (continued)

Reverse the cutting arm 180 degrees as shown in the Figure 23, and re-tension the V-belt by turning the belt tensioning

cam .The V-belt should remain in tension.

Fully tighten the three nuts	that lock theV-belt into the proper
tensioning position.

Figure 23. Reversing the Cutting Arm


Re-attach the cover guard	with the 2 cap screws		,
and reconnect the guard adjustment knob		.

Figure 24. Re-attaching Cover Guard

PAGE 24 — HS62A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #0 (03/20/06)

Image 24

Contents SideWinder Page Page HS62A CUT-OFF SAW Table of Contents Best Deal! Order via Internet Dealers Only Order via Fax Dealers OnlyHS62A CUT-OFF SAW Safety Message Alert Symbols HS62A CUT-OFF SAW Safety Message Alert Symbols Always wear approved eye and hearing protectionRotating blade can cut and crush. Keep hands and feet clear Safety HS62A CUT-OFF SAW Rules for Safe OperationGeneral Safety HS62A CUT-OFF SAW Rules for Safe OperationBlade Diamond Blade Safety Saw Transportation SafetyNever use carbide-tipped or toothed type blades of any kind HS62A CUT-OFF SAW Rules for Safe Operation EmergenciesAlways know the location of the nearest first aid kit Displacement Dimensions LxWxHEngine Type Engine Speed 10,000Machine Operation And Safety Decals Safety Decals10 9 8 7 6 HS62A CUT-OFF SAW Controls & Components HS62A CUT-OFF SAW Blade Installation Instructions StepBlade shaft HS62A CUT-OFF SAW Water KIT Installation Instructions Fasten the clamp to the Roller Bar Support ArmHS62A CUT-OFF SAW Blades Preparation / PRE-INSPECTIONBlades SAW Blade InspectionPlace the engine ON/OFF switch in the on position HS62A CUT-OFF SAW Initial START-UP/OPERATIONInitial START-UP Fuel CheckOperation Shut-downBelt Changing Procedure KnobCover Guard Until the V-belt is completely slackedHS62A CUT-OFF SAW Maintenance Re-install the guardV-belt should remain in tension Tensioning positionReversing the Cutting Arm Procedure Cam .The V-belt should remain in tension Re-attach the cover guardHS62A CUT-OFF SAW Maintenance AIR/FUEL Filter Air/Fuel Filter Maintenance ProceduresHS62A CUT-OFF SAW Troubleshooting Blade HS62A CUT-OFF SAW Troubleshooting Engine Troubleshooting EngineTroubleshooting Engine Spark plug heat value improper?HS62A CUT-OFF SAW Filter Kits Includes 1 eaHS62A CUT-OFF SAW Explanation of Parts Section Remarks NO. ColumnPart NO. Column QTY. ColumnHS62A CUT-OFF SAW Suggested Spare Parts To 3 UnitsHS62A CUT-OFF SAW Muffler Assy Part Name HS62A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope HS62A CUT-OFF SAW Crankcase Assy Plate HS62A CUT-OFF SAW V-BELT Cover Clutch Side Assy Belt COVER, Clutch Side HS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS62A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS62A CUT-OFF SAW Fuel Tank Assy Part Name QTY Remarks HS62A CUT-OFF SAW Lifting Handle and Roller Assy Handle HS62A CUT-OFF SAW Throttle Linkage Assy HS62A CUT-OFF SAW -THROTTLE Linkage Assy HS62A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat HS62A CUT-OFF SAW Flywheel Assy Pawl SET HS62A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug HS62A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP HS62A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy HS62A CUT-OFF SAW Carburetor Assy Throttle Shaft HS62A CUT-OFF SAW Crankshaft / Piston Assy HS62A CUT-OFF SAW Crankshaft and Piston Assy HS62A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF HS62A CUT-OFF SAW Tools HS4191240 00325Recommended Diamond Blades For Your Side Winder Saw HS62A CUT-OFF SAW Recommended Diamond BladesPayment Terms United States Mexico United KingdomCanada Brazil Your Local Dealer is

Related manuals

Manual 70 pages 2.48 Kb