Multiquip FS2 Blade Shaft Bearing Replacement, Replacement of the Blade Shaft Bearings

Page 30

FS2 CONCRETE SAW — MAINTENANCE

Blade Shaft Bearing Replacement

The FS2 is supported by “tapped base lock collar (w/set screw)’ self-aligning blade shaft bearings. These heavy duty bearings support the 1-1/4 blade shaft, and have grease (zerk) points (Figures 24 and 25) conveniently located for service.

3.To loosen the tension on the three V-Belts perform the following:

λRemove the Belt Cover, item 4, page 42. (Pointers and Covers Assembly)

λLoosen the Carriage Bolts, item 11, page 40 (Engine Mount Assembly).

λLoosen the Hex Head Cap Screws, item 12, page 40 (Engine Mount Assembly).

λRotate the engine down to provide slack in the V-Belts

Figure 24. Left-Side Shaft Bearing

1.Reference pages 38 ( Blade Shaft Assembly) and 40( Engine Mount Assembly).

2.Its recommended to replace both left & right hand bearings collectively.

Replacement of the Blade Shaft Bearings

4.Perform the following to replace the blade shaft bearings:

λRemove Blade Flanges (items 7 and 8, page 38, Blade Shaft Assembly) as required to permit the Shaft Bearing(s) to slide off the Blade Shaft.

λLoosen/remove Shaft Bearing(s) Hex Head Cap Screws, item 11, page 38.

λLoosen Set Screw on the Blade Shaft Bearing collar.

λSlide “old” Bearing(s) off the Blade Shaft and replace with “new” Bearing(s)- grease (zerk) fitting pointing forward, and the lock collar oriented to the “right" as you face the saw.

5.Loosely bolt the bearing(s) into place on the saw frame, then ensure the alignment by referencing past bearing position- ing.

6.Tighten the hex head cap screw, item 11, page 38 to secure the Shaft Bearing (s) to the frame.

7.To complete the re-installation process , reverse the order of

the above mentioned steps. For V-belt adjustment, see V-belt tension section on page 23 (Figure 14).

Figure 25. Right-Side Shaft Bearing

PAGE 30 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

Image 30
Contents Concrete SAW Page Heres HOW to GET Help Table of Contents Parts Ordering Procedures UPS Ground Service at no charge for freightFS2 Concrete SAW Safety Message Alert Symbols Seriously injured if you do not follow directionsFS2 Concrete SAW Safety Message Alert Symbols Always wear approved respiratory protectionAlways wear approved eye and hearing protection Machine Safety Decals FS2 Concrete SAW DecalsGeneral Safety FS2 Concrete SAW Rules for Safe OperationNever tow the saw behind a vehicle Stop the engine when leaving the saw unattendedFS2 Concrete SAW Rules for Safe Operation Never transport the saw with the blade mountedMaintenance Safety FS2 Concrete SAW Rules for Safe OperationEmergencies FS2 Concrete SAW Dimensions FS2 Concrete Saw DimensionsWeights FS2 Concrete SAW Basic Components FS2 Concrete Saw Basic ComponentsDescription Mixture FS2 Concrete SAW Basic Engine ComponentsFlow of fuel Muffler Used to reduce noise and emissionsFS2 Concrete SAW General Information Manual Cyclone Air FiltrationFS2 Concrete SAW General Information Under Carriage SystemTACHOMETER/ Hourmeter Engine Oil Check Read safety instructions at the beginning of manualBefore Starting Gasoline CheckOperating area FS2 Concrete SAW Inspection -BLADERotation downcuts with the turn of the shaft Poor performance and/or blade damageSaw FS2 Concrete SAW Inspection -BLADE PlacementWhen finalizing the assembly Tight closure on the surface of the bladeFS2 Concrete SAW Inspection -GUARDS, Covers and V-BELTS Belt Tension Place the Engine ON/OFF switch in the on position FS2 Concrete SAW- Initial START-UPStopping the Engine Maneuvering The SawBlade is spinning whenever the engine is running Wet Saw Operation FS2 Concrete SAW OperationSaw Alignment Advance engine throttle to full Fast positionFinishing a Cut Dry Saw OperationDiamond Blades and Blade Speed Blade SpeedBearing Lubrication Care FS2 Concrete SAW MaintenanceGeneral Cleanliness General Engine CareBlade Shaft Bearing Replacement Replacement of the Blade Shaft BearingsBelt Replacement Raise/Lower Height AdjustmentSetting The Height Of The Depth Gauge Pointer Belt Tension CheckFS2 Concrete SAW Explanation of Code in Remarks Column Items Found In the Remarks ColumnItems Found In the Items Number Column FS2 Concrete SAW Suggested Spare Parts To 3 UnitsFS2 Concrete SAW Troubleshooting Engine Engine TroubleshootingFS2 Concrete SAW Troubleshooting Engine Engine TroubleshootingFS2 Concrete SAW Under Carriage Assy 2621 150281162A 15090FS2 Concrete SAW Blade Shaft Assy 15066 151196059B KEY, 1/4 SQ X 15065 15063FS2 Concrete SAW Engine Mount Assy 15032 1515615033 15157FS2 Concrete SAW Pointers and Covers Assy 0730 SCREW, HHC 1/4-20 X 15011 1505315070 0131A SCREW, HHC 1/4-20 X 3/4 15052FS2 Concrete SAW Water System Assy 15538 CLAMP, Worm HOSE, 7/16-11/16 15137 1513515181 15183FS2 Concrete SAW Basic Platform Assy 0730 SCREW, HHC 1/4-20 15664 1500115105 15018FS2 Concrete SAW Blade Mist 14-INCH Assy 10176 NUT, Nyloc 1/2-13 15151 0131A SCREW, HHC 1/4-20 X 3/4 094915509 15160FS2 Concrete SAW Blade Mist 18 -INCH Assy 10176 NUT, Nyloc 1/2-13 15449 15204FS2 Concrete SAW Manual Raise and Lower Assy 15517 150831577 15080FS2 Concrete SAW Engine Assy 15102 1551115101 15103Terms and Conditions of Sale Parts Page Multiquip INC