Multiquip operation manual FS2 Concrete SAW Safety Message Alert Symbols

Page 6

FS2 CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.

NOTE

This Owner's Manual has been developed to provide complete instructions for the safe and efficient operations of the MQWhiteman FS2 Concrete Saw. Depending on the power plant you have selected, please refer to the engine manufacturers instructions for data relative to its safe operations.

Before using this Concrete Saw, ensure that the operating individual has read and understands all instructions in this manual.

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER, WARNING, or CAUTION.

DANGER: You WILL be KILLED or

SERIOUSLY injured if you do not follow directions.

WARNING: You CAN be KILLED or

SERIOUSLY injured if you do not follow directions.

CAUTION: You CAN be injured if you do not follow directions.

Potential hazards associated with Concrete Saw operations will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols.

HAZARD SYMBOLS

Lethal Exhaust Gases

Engine exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. NEVER operate this equipment in a confined area or enclosed structure that does not provide ample free flow air.

Explosive Fuel

Gasoline is extremely flammable, and its vapors can cause an explosion if ignited. DO NOT start the engine near spilled fuel or combustible fluids. DO NOT fill the fuel tank while the engine is running or hot. DO NOT overfill tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system. Store fuel in approved containers, in well-ventilated areas and away from sparks and flames. NEVER use fuel as a cleaning agent.

Burn Hazards

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. Never operate the engine with heat shields or heat guards removed.

Rotating Parts

NEVER operate equipment with covers, or guards removed. Keep fingers, hands, hair and clothing away from all moving parts to prevent injury.

PAGE 6 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #2 (11/08/01)

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Concrete SAW Page Heres HOW to GET Help Table of Contents Parts Ordering Procedures UPS Ground Service at no charge for freightFS2 Concrete SAW Safety Message Alert Symbols Seriously injured if you do not follow directionsFS2 Concrete SAW Safety Message Alert Symbols Always wear approved respiratory protectionAlways wear approved eye and hearing protection Machine Safety Decals FS2 Concrete SAW DecalsGeneral Safety FS2 Concrete SAW Rules for Safe OperationNever tow the saw behind a vehicle Stop the engine when leaving the saw unattendedFS2 Concrete SAW Rules for Safe Operation Never transport the saw with the blade mountedMaintenance Safety FS2 Concrete SAW Rules for Safe OperationEmergencies FS2 Concrete SAW Dimensions FS2 Concrete Saw DimensionsWeights FS2 Concrete SAW Basic Components FS2 Concrete Saw Basic ComponentsDescription Mixture FS2 Concrete SAW Basic Engine ComponentsFlow of fuel Muffler Used to reduce noise and emissionsFS2 Concrete SAW General Information Manual Cyclone Air FiltrationFS2 Concrete SAW General Information Under Carriage SystemTACHOMETER/ Hourmeter Engine Oil Check Read safety instructions at the beginning of manualBefore Starting Gasoline CheckOperating area FS2 Concrete SAW Inspection -BLADERotation downcuts with the turn of the shaft Poor performance and/or blade damageSaw FS2 Concrete SAW Inspection -BLADE PlacementWhen finalizing the assembly Tight closure on the surface of the bladeFS2 Concrete SAW Inspection -GUARDS, Covers and V-BELTS Belt Tension Place the Engine ON/OFF switch in the on position FS2 Concrete SAW- Initial START-UPStopping the Engine Maneuvering The SawBlade is spinning whenever the engine is running Wet Saw Operation FS2 Concrete SAW OperationSaw Alignment Advance engine throttle to full Fast positionFinishing a Cut Dry Saw OperationDiamond Blades and Blade Speed Blade SpeedBearing Lubrication Care FS2 Concrete SAW MaintenanceGeneral Cleanliness General Engine CareBlade Shaft Bearing Replacement Replacement of the Blade Shaft BearingsBelt Replacement Raise/Lower Height AdjustmentSetting The Height Of The Depth Gauge Pointer Belt Tension CheckFS2 Concrete SAW Explanation of Code in Remarks Column Items Found In the Remarks ColumnItems Found In the Items Number Column FS2 Concrete SAW Suggested Spare Parts To 3 UnitsFS2 Concrete SAW Troubleshooting Engine Engine TroubleshootingFS2 Concrete SAW Troubleshooting Engine Engine TroubleshootingFS2 Concrete SAW Under Carriage Assy 2621 150281162A 15090FS2 Concrete SAW Blade Shaft Assy 15066 151196059B KEY, 1/4 SQ X 15065 15063FS2 Concrete SAW Engine Mount Assy 15032 1515615033 15157FS2 Concrete SAW Pointers and Covers Assy 0730 SCREW, HHC 1/4-20 X 15011 1505315070 0131A SCREW, HHC 1/4-20 X 3/4 15052FS2 Concrete SAW Water System Assy 15538 CLAMP, Worm HOSE, 7/16-11/16 15137 1513515181 15183FS2 Concrete SAW Basic Platform Assy 0730 SCREW, HHC 1/4-20 15664 1500115105 15018FS2 Concrete SAW Blade Mist 14-INCH Assy 10176 NUT, Nyloc 1/2-13 15151 0131A SCREW, HHC 1/4-20 X 3/4 094915509 15160FS2 Concrete SAW Blade Mist 18 -INCH Assy 10176 NUT, Nyloc 1/2-13 15449 15204FS2 Concrete SAW Manual Raise and Lower Assy 15517 150831577 15080FS2 Concrete SAW Engine Assy 15102 1551115101 15103Terms and Conditions of Sale Parts Page Multiquip INC
Top Page Image Contents