Multiquip manual HS62 CUT-OFF SAW Initial START-UP/OPERATION, Fuel Check, Starting

Page 23

HS62 CUT-OFF SAW — INITIAL START-UP/OPERATION

INITIAL START-UP

CAUTION

DO NOT attempt to operate the saw until the Safety, General Information and Inspection sections of this manual have been read and thoroughly understood. Depending on engine manufacturer, operating steps may vary. See engine manufactures operating manual.

CAUTION

NEVER operate the saw in a confined area or enclosed area structure that does not provide ample free flow of air.

ALWAYS wear approved eye and hearing protection before operating the saw.

NEVER place hands or feet inside the belt guard or blade guard while the engine is running. ALWAYS shut the engine down before performing any kind of maintenance service on the saw.

Explosive Fuel

Fuel Check

Motor fuels are highly flammable and can be dangerous if mishandled. DO NOT smoke while refueling. DO NOT attempt to refuel the saw if the engine is hot! or running.

1.Remove the fuel cap located on the side of the saw.

2.Visually inspect to see if fuel level is low. If fuel is low, replenish with fuel oil mixture as shown in Figure 22.

3.When refueling, be sure to use a strainer for filtration. DO NOT top-off fuel. Wipe up any spilled fuel.

This saw uses a 2-stroke engine which requires a mixture of premium 92 octane

NOTE unleaded gasoline and smoke free 2-stroke motor oil. See Figure 25.

Figure 25. Fuel to Oil Mixture

For correct fuel to oil mixture, add 2.6 fl. oz (29.6 ml) of 2-stroke motor oil to 1 gallon (3.8

NOTE liters) of premium 92 octane unleaded gasoline. For a 5 gallon can of premium unleaded gasoline add 13 fl. oz (384 ml) of 2-stroke motor oil.

A bottle ( 2.6 fl. oz) of smokeless 2-stroke motor oil cannot be purchased separately.Only a case of 36 individual bottles can be purchased. When ordering use Multiquip P/N 00325.

Starting

1.Place the engine ON/OFF switch in the ON position

2.Using your thumb, press down on the throttle lock lever, while squeezing the throttle trigger.This will lock the throttle in the half-throttleposition.

3.Pull the choke lever all the way out to the CLOSED position.

4.Pull the decompression button outward.

5.Place the saw on level ground. Make sure the saw blade is free to rotate and will not come into contact with any foreign objects.

6.Hold the front handle firmly with the left hand and put your right foot onto the base of the rear handle.

The CLOSED position of the choke lever enriches the fuel mixture for starting a COLD

NOTE engine. The OPEN position provides the correct fuel mixture for normal operation after starting, and for restarting a warm engine.

HS62 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #5 (09/12/05) — PAGE 23

Image 23
Contents SideWinder Page HS62 CUT-OFF SAW Operation & Parts Manual REV. #5 09/12/05 HS62 CUT-OFF SAW Table of Contents HS62 CUT-OFF SAW Parts Ordering Procedures Foryour Safety and the Safety of Others HS62 CUT-OFF SAW Safety Message Alert SymbolsRotating blade can cut and crush. Keep hands and feet clear HS62 CUT-OFF SAW Safety Message Alert SymbolsAlways wear approved eye and hearing protection Before servicing the saw HS62 CUT-OFF SAW Rules for Safe OperationHS62 CUT-OFF SAW Rules for Safe Operation General SafetyNever use carbide-tipped or toothed type blades of any kind Diamond Blade SafetySaw Transportation Safety Always know the location of the nearest first aid kit HS62 CUT-OFF SAW Rules for Safe OperationDimensions LxWxH Dimensions Shipping LxWxHWeight DisplacementDCL HS62 CUT-OFF SAW Decal PlacementMachine Operation And Safety Decals HS62 CUT-OFF SAW Controls & Components Decompression Valve Push inward when starting engineHS62 CUT-OFF SAW Controls & Components Removed items HS62 CUT-OFF SAW SAW Assembly InstructionsHS62 CUT-OFF SAW SAW Assembly Instructions Blade shaft Blade Installation ProcedureOuter flange Y, and inner dual-arbor flange Z Reversing the Cutting Arm Procedure Re-attach the cover guard Cam .The V-belt should remain in tensionInto the proper tensioning position See page 63-63 for Water Kit part number HS62 CUT-OFF SAW Water KIT Installation ProcedureDiamond Blade HS62 CUT-OFF SAW BladesStarting Place the engine ON/OFF switch in the on positionHS62 CUT-OFF SAW Initial START-UP/OPERATION Fuel CheckShut-down HS62 CUT-OFF SAW Initial START-UP/OPERATIONAir/Fuel Filter Maintenance Procedures HS62 CUT-OFF SAW MaintenanceBlade Troubleshooting HS62 CUT-OFF SAW Troubleshooting SAWTroubleshooting Engine HS62 CUT-OFF SAW Troubleshooting EngineTroubleshooting Engine Includes 1 ea Water Filter fits both HS62 & HS81 HS62 CUT-OFF SAW Filter KitsQTY. Column HS62 Explanation of Parts Section RemarksNO. Column Part NO. ColumnTo 3 Units HS62 CUT-OFF SAW Suggested Spare PartsHS62 CUT-OFF SAW Muffler Assy Part Name HS62 CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope HS62 CUT-OFF SAW Crankcase Clutch Side Assy Choke Lever HS62 CUT-OFF SAW Crankcase Flywheel Side Assy Part Name QTY Remarks HS62 CUT-OFF SAW V-BELT Cover Clutch Side Assy Belt COVER, Clutch Side HS62 CUT-OFF SAW V-BELT Cover Pulley / Blade Guard Assy HS62 CUT-OFF SAW V-BELT Cover Pulley / Blade Guard Assy HS62 CUT-OFF SAW FUEL, Lifting HANDLE, and Roller Assy Handle HS62 CUT-OFF SAW -THROTTLE Linkage Assy Throttle Linkage HS62 CUT-OFF SAW Flywheel Cover Assy FLANGE, Starter HS62 CUT-OFF SAW Flywheel Assy Pawl SET HS62 CUT-OFF SAW Ignition Coil Assy COVER, AIR Filter Lower HS62 CUT-OFF SAW AIR Filter Assy KNOB, AIR Filter Cover HS62 CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy HS62 CUT-OFF SAW Carburetor Assy PIN, Fulcrum HS62 CUT-OFF SAW Crankshaft / Piston Assy HS62 CUT-OFF SAW Crankshaft and Piston Assy HS62 CUT-OFF SAW Water KIT Assy FITTING, Quick Disconnect Plastic TIE Wraps Hose Clamp HS62 CUT-OFF SAW Tools 00325 HS4191240Material to Cut HS62 CUT-OFF SAW Recommended Diamond BladesEffective October 1, 2002 Terms and Conditions of Sale Parts Your Local Dealer is Heres HOW to GET Help
Related manuals
Manual 42 pages 34.19 Kb

HS62 specifications

The Multiquip HS62 is a powerful, high-performance concrete pump designed to deliver exceptional results in various construction applications. Known for its durability and efficiency, the HS62 is particularly valued by contractors for its versatility and reliability on job sites.

One of the standout features of the Multiquip HS62 is its robust, heavy-duty construction. Made from high-quality materials, the pump is engineered to withstand the rigors of demanding environments, ensuring longevity and reduced maintenance costs. The frame is designed for stability and ease of transport, making it an ideal choice for both commercial and residential projects.

The HS62 comes equipped with a 62-horsepower engine, providing ample power for demanding pumping tasks. This engine drives a hydraulically-operated system that allows the pump to handle a wide variety of concrete mixes, including high-slump and low-slump materials. With a maximum concrete output of up to 64 cubic yards per hour, the HS62 can efficiently tackle large-scale pouring jobs, reducing the time and labor required.

In addition to its powerful engine, the HS62 features advanced technology that enhances its performance. The intelligent control system allows for precise adjustments to the pumping pressure and flow rate, ensuring optimal performance for different applications. This adaptability leads to a smoother operation and reduced wear on the pump components, which can extend the machine's service life.

Safety is a paramount concern with any construction equipment, and the HS62 incorporates several safety features to protect users and equipment alike. It is equipped with emergency stop buttons and adjustable pressure relief valves, which help prevent accidents during operation. Furthermore, the intuitive design of the control panel allows operators to monitor performance and make real-time adjustments easily.

Another characteristic that sets the Multiquip HS62 apart is its ease of maintenance. The pump's design prioritizes accessibility, allowing for quick inspections and repairs without extensive downtime. This focus on user-friendliness ensures that operators can keep the equipment in top working condition, maximizing productivity on the job site.

Overall, the Multiquip HS62 is a reliable and efficient concrete pump that combines power, advanced technology, and user-friendly design to meet the demands of modern construction projects. Whether it’s for commercial building sites, road work, or large residential pours, the HS62 sets a high standard in the concrete pumping industry, making it a valuable asset for any contractor.