Multiquip manual HS62 CUT-OFF SAW Initial START-UP/OPERATION, Shut-down

Page 24

HS62 CUT-OFF SAW — INITIAL START-UP/OPERATION

7.Grasp the starter grip and slowly pull it out.The resistance becomes the hardest at a certain position, corresponding to thecompressionpoint.Pullthestartergripbrisklyandsmoothly forstarting.

8.If the engine has started, slowly return the choke lever to the "OPEN" position. If the engine has not started repeat steps 1 through 9.

9.Squeeze the throttle lever trigger to release it from the half- throttle position.

10.Before the saw is placed into operation, run the engine for severalminutes. Checkforfuelleaks,andnoisesthatwould associate with a loose guards and/or covers.

OPERATION

WARNING

ALWAYS cut with the saw at FULLTHROTTLE. Attempting to cut with the saw at less than full throttle could cause the blade to bind or stop abruptly in the slab resulting in serious injury to the operator or others in the area.

NOTE

Markthecuttinglineclearlyandalways

 

saw in a STRAIGHT LINE ONLY.

4.When the end of the cut has been reached, raise the blade out of the cut .

5.Ifcuttingiscomplete,turntheengineoffandwaitfortheblade to stop rotating.

Shut-down

1.Let the engine idle for 3-5 minutes.

2.Place the engine ON/OFF switch to the OFF position

3.Wait for the blade to stop spinning before handling the saw.

4.DO NOT touch the cutting blade it is very hot!, allow it to cool, severe burn condition exists.

WARNING

ALWAYS keep clear of rotating or moving parts while operating this equipment.

2.To begin sawing, lower the rotating blade allowing it to cut to the preset depth.

3.When blade has reached full cutting depth, slowly walk behind the saw at a rate that will allow the engine to operate without losing optimum RPM.

CAUTION

DO NOT try to cut faster than the blade will allow. Cutting too fast will cause the blade to rise up out of the cut. Improper cutting rate can decrease the life of the engine and blades.

PAGE 24 — HS62 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #5 (09/12/05)

Page 23 Page 25
Image 24
Page 23 Page 25
Contents SideWinder Page HS62 CUT-OFF SAW Operation & Parts Manual REV. #5 09/12/05 HS62 CUT-OFF SAW Table of Contents HS62 CUT-OFF SAW Parts Ordering Procedures HS62 CUT-OFF SAW Safety Message Alert Symbols Foryour Safety and the Safety of OthersHS62 CUT-OFF SAW Safety Message Alert Symbols Always wear approved eye and hearing protectionRotating blade can cut and crush. Keep hands and feet clear HS62 CUT-OFF SAW Rules for Safe Operation Before servicing the sawGeneral Safety HS62 CUT-OFF SAW Rules for Safe OperationDiamond Blade Safety Saw Transportation SafetyNever use carbide-tipped or toothed type blades of any kind HS62 CUT-OFF SAW Rules for Safe Operation Always know the location of the nearest first aid kitDimensions Shipping LxWxH WeightDisplacement Dimensions LxWxHHS62 CUT-OFF SAW Decal Placement Machine Operation And Safety DecalsDCL Decompression Valve Push inward when starting engine HS62 CUT-OFF SAW Controls & ComponentsHS62 CUT-OFF SAW Controls & Components HS62 CUT-OFF SAW SAW Assembly Instructions Removed itemsHS62 CUT-OFF SAW SAW Assembly Instructions Blade Installation Procedure Outer flange Y, and inner dual-arbor flange ZBlade shaft Reversing the Cutting Arm Procedure Cam .The V-belt should remain in tension Into the proper tensioning positionRe-attach the cover guard HS62 CUT-OFF SAW Water KIT Installation Procedure See page 63-63 for Water Kit part numberHS62 CUT-OFF SAW Blades Diamond BladePlace the engine ON/OFF switch in the on position HS62 CUT-OFF SAW Initial START-UP/OPERATIONFuel Check StartingHS62 CUT-OFF SAW Initial START-UP/OPERATION Shut-downHS62 CUT-OFF SAW Maintenance Air/Fuel Filter Maintenance ProceduresHS62 CUT-OFF SAW Troubleshooting SAW Blade TroubleshootingHS62 CUT-OFF SAW Troubleshooting Engine Troubleshooting EngineTroubleshooting Engine HS62 CUT-OFF SAW Filter Kits Includes 1 ea Water Filter fits both HS62 & HS81HS62 Explanation of Parts Section Remarks NO. ColumnPart NO. Column QTY. ColumnHS62 CUT-OFF SAW Suggested Spare Parts To 3 UnitsHS62 CUT-OFF SAW Muffler Assy Part Name HS62 CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope HS62 CUT-OFF SAW Crankcase Clutch Side Assy Choke Lever HS62 CUT-OFF SAW Crankcase Flywheel Side Assy Part Name QTY Remarks HS62 CUT-OFF SAW V-BELT Cover Clutch Side Assy Belt COVER, Clutch Side HS62 CUT-OFF SAW V-BELT Cover Pulley / Blade Guard Assy HS62 CUT-OFF SAW V-BELT Cover Pulley / Blade Guard Assy HS62 CUT-OFF SAW FUEL, Lifting HANDLE, and Roller Assy Handle HS62 CUT-OFF SAW -THROTTLE Linkage Assy Throttle Linkage HS62 CUT-OFF SAW Flywheel Cover Assy FLANGE, Starter HS62 CUT-OFF SAW Flywheel Assy Pawl SET HS62 CUT-OFF SAW Ignition Coil Assy COVER, AIR Filter Lower HS62 CUT-OFF SAW AIR Filter Assy KNOB, AIR Filter Cover HS62 CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy HS62 CUT-OFF SAW Carburetor Assy PIN, Fulcrum HS62 CUT-OFF SAW Crankshaft / Piston Assy HS62 CUT-OFF SAW Crankshaft and Piston Assy HS62 CUT-OFF SAW Water KIT Assy FITTING, Quick Disconnect Plastic TIE Wraps Hose Clamp HS62 CUT-OFF SAW Tools HS4191240 00325HS62 CUT-OFF SAW Recommended Diamond Blades Material to CutEffective October 1, 2002 Terms and Conditions of Sale Parts Heres HOW to GET Help Your Local Dealer is
Related manuals
Manual 42 pages 34.19 Kb

HS62 specifications

The Multiquip HS62 is a powerful, high-performance concrete pump designed to deliver exceptional results in various construction applications. Known for its durability and efficiency, the HS62 is particularly valued by contractors for its versatility and reliability on job sites.

One of the standout features of the Multiquip HS62 is its robust, heavy-duty construction. Made from high-quality materials, the pump is engineered to withstand the rigors of demanding environments, ensuring longevity and reduced maintenance costs. The frame is designed for stability and ease of transport, making it an ideal choice for both commercial and residential projects.

The HS62 comes equipped with a 62-horsepower engine, providing ample power for demanding pumping tasks. This engine drives a hydraulically-operated system that allows the pump to handle a wide variety of concrete mixes, including high-slump and low-slump materials. With a maximum concrete output of up to 64 cubic yards per hour, the HS62 can efficiently tackle large-scale pouring jobs, reducing the time and labor required.

In addition to its powerful engine, the HS62 features advanced technology that enhances its performance. The intelligent control system allows for precise adjustments to the pumping pressure and flow rate, ensuring optimal performance for different applications. This adaptability leads to a smoother operation and reduced wear on the pump components, which can extend the machine's service life.

Safety is a paramount concern with any construction equipment, and the HS62 incorporates several safety features to protect users and equipment alike. It is equipped with emergency stop buttons and adjustable pressure relief valves, which help prevent accidents during operation. Furthermore, the intuitive design of the control panel allows operators to monitor performance and make real-time adjustments easily.

Another characteristic that sets the Multiquip HS62 apart is its ease of maintenance. The pump's design prioritizes accessibility, allowing for quick inspections and repairs without extensive downtime. This focus on user-friendliness ensures that operators can keep the equipment in top working condition, maximizing productivity on the job site.

Overall, the Multiquip HS62 is a reliable and efficient concrete pump that combines power, advanced technology, and user-friendly design to meet the demands of modern construction projects. Whether it’s for commercial building sites, road work, or large residential pours, the HS62 sets a high standard in the concrete pumping industry, making it a valuable asset for any contractor.
Top Page Image Contents