Multiquip SP2S13H20A manual Hydrostatic Transmission, Additionally, when connecting the positive

Page 19

INSPECTION

Hydrostatic Transmission

An EATON® Model 7 hydrostatic transmission (Figure 8) provides the power for the saw's propulsion system. The transmission drives a sprocket that directly connects the spline drive to the rear wheels. The no load forward/reverse speeds are approximately 80 ft/min.

Figure 8. Hydrostatic Transmission

The transmission is factory filled with approved hydraulic fluid that has a viscosity equivalent to SAE 20W-20. Should additional servicing be required, the following hydraulic fluids are recommended:

General Motors Dextron B

Ford MM2C-33F

Ford M2C-41A

International harvester Hy-Tran Fluids

Figure 9.Transmission Reservoir

CAUTION

DO NOT over fill the fluid reservoir (Figure 10). Note the level marks on the reservoir.It is essential to reference the existing oil conditions (A) cold or (B) hot prior to operating the saw. Overfilling the transmission with hydraulic fluid may cause the seals to rupture causing mechanical damage.

Battery - The 12-volt DC battery (Figure 10) is shipped dry, and will require a proper electrolyte level for operation.

Figure 10. Battery

When servicing of the battery is required perform the following:

A face shield and rubber gloves should be worn while handling and servicing battery's electrolyte.

Disconnect battery terminal clamps, and remove the battery from the saw when servicing is required.

DO NOT overfill the battery.

WARNING

Electrolyte is an acid and must be handled with caution. Servicing instructions from the electrolyte manufacturer must ALWAYS be followed to ensure safety.Serious injury can result from careless handling and noncompliance to safety handling instructions.

Overfilling the battery may cause the electrolyte to overflow resulting in corrosion to nearby components. Immediately wash off any spilled electrolyte (battery acid).

Additionally, when connecting the positive

(+)cable to the battery's positive (+) terminal post, DO NOT allow contact of the wrench or any metallic part to come in contact with the battery's negative (-) terminal post.This may result in an electrical short circuit or an explosion.

Use only distilled water in the

NOTEbattery.Tap water can reduce the operating life of the battery.

SP2S13H20A SAW — OPERATION AND PARTS MANUAL — REV. #1 (05/17/10) — PAGE 19

Image 19
Contents Model SP2S13H20A Proposition 65 Warning Respiratory Hazards SILICOSIS/RESPIRATORY Warnings Silicosis WarningTable of Contents Best Deal! Order via Internet Dealers Only Parts Ordering ProceduresOrder via Fax Dealers Only Specifications SpecificationsSP2S13H20A Dimensions DimensionsIf you do not follow these directions Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionRules for Safe Operation Rules for Safe OperationDiamond Blade Safety General Safety Always know the location of the nearest first aid kit Maintenance SafetySaw Transportation Safety EmergenciesSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 SP2S13H20A Saw Major Components Major ComponentsFlow of fuel Cannister to gain access to filter element13HP Honda Engine Components SmoothlyGeneral Information SP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Honda 13 HP engine shown InspectionBefore Starting Engine Oil CheckHydrostatic Transmission Additionally, when connecting the positiveUse only distilled water Poor performance and/or blade damage Inspection -BLADERotation downcuts with the turn of the shaft Or others in the operating areaInner flange collar Inspection Blade PlacementSet the engine ON/OFF switch to the OFF position FlangeBelts Alignment and Tensioning Inspection -GUARDS, Covers & BeltsGuards and Covers Check Institute Ansi B7.1 and B7.5Inspection Belts & Water Tank Replacement part numbersWater Tank Fuel Valve Lever Manual START-UP do not pull the starter rope all the way to the end Started repeat steps 1 throughBlade operating speeds Associate with a loose guard and/or coversStopping the Engine 13 HP Honda Engine SHUT-DOWN ProceduresPlace the fuel valve lever to the OFF position SP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Operation Adjusting the Handle BarsAdjusting the Blade Height When moving the saw aroundPlace the travel lever in the Neutral position Traveling During CuttingEngage Position Follow steps 1-4 of the Traveling During Cutting section CuttingWet Cutting Operation Turn water source on FigureExtreme heat Diamond Blades Finishing a CutBlade Speed Maintenance Spline GearWheels Retighten the adjustment nutGeneral Transmission Care Transmission Reservoir CupDriveV-Belt Check AdjustV-Belt Alignment/Replacement PulleysLoosen the 4 1-1/2 HHC screws Engine Mount Assy., item Reference & for steps Blade Shaft Bearing ReplacementBattery Electrolyte Levels Battery MaintenanceHP Honda Engine Wiring Diagram 13HP Engine Wiring Diagram Recoil StartEngine Troubleshooting Troubleshooting EngineEngine Troubleshooting Blade Troubleshooting Troubleshooting BladeSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Xxxxx only Not Used on Explanation of Code in Remarks ColumnDescription Suggested Spare PartsName Plate and Decals Name Plate and DecalsDECAL, FORWARD/REVERSE Lever DECAL, Recommended MaintenanceDECAL, Multiquip DECAL, SP2S13H20AUnder Carriage Assy Under Carriage AssyBearing Plain AXLE, Rear & FrontFRAME, Undercarriagee Assy WASHER, Flat SAE 3/4Blade Shaft Assy Blade Shaft AssyNUT, HEX JAM LH 1-14 Plated SPINDLE, BladeFLANGE, Blade Inside 4.0OD X 1.0ID KEY, Woodruff #15Lifting Bale Assy Lifting Bale AssyBRACE, 20HP Bail 13HP, Lift Bale Assy20HP, Lift Bail Assy BRACE, 13HP BailConsole Assy Console AssyWASHER, Lock 3/8 MED Housing ASSY. REDHandle Assy GRIP, 1 ID13HP Honda Engine Mount Assy 13HP Honda Engine Mount AssyEngine Base Assy NUT, HEX Finish 1/2-13Engine Assy See Blade Shaft Assy See Hydrostatic Drive Assy Engine AssyPart Name QTY. Remarks Engine AssyPointers and Covers Assy Pointers and Covers AssyPointer Pointer and Covers AssyBlade Guide Weldment Spanner Bushing CSIWater System Assy Water System AssyFITTING, Brass 1/2 Barb X 3/4 Grdn FITTING, Plastic 90 1/2MP X 1/2BARBFITTING, Nipple 1/2MP X 2 Galv Bolt W/NUTSBlade Guard Assy Blade Guard AssySpring TENSION, Guard Blade Connector 3/8Blade Guard W/A RED GUARD, Splash BladeManual Raise and Lower Assy Manual Raise and Lower AssyBEARING, Flange Jack Screw Assy BladeJackpost Assy JackscrewBattery Assy Battery AssyNUT, HEX Finish 5/16-18 Bracket BatteryBattery Hold Down KIT STRAP, GroundTransmission Engage Lever Assy Transmission Engage Lever AssyWASHER, Flat SAE 3/8 HYD. Transmission Engage Lever AssyHydrostatic Transmission Hydrostatic Transmission AssyHydrostatic Transmission Assy Hydrostatic Drive Assy Hydrostatic Drive AssyCHAIN, Roller .375 Pitch X AIR Cleaner Assy Honda GX390K1QWT2 Engine AIR Cleaner AssyCollar B, AIR Cleaner SEAL, AIR Cleaner CoverGROMMET, AIR Cleaner COLLAR, AIR CleanerCamshaft Assy Honda GX390K1QWT2 Engine Camshaft AssyLIFTER, Valve SPRING, Weight ReturnROD, Push ARM, Valve RockerCarburetor Assy Honda GX390K1QWT2 Engine Carburetor AssyFloat SET PLATE, Lever SettingGasket SET Valve SET, FloatControl Assy Honda GX390K1QWT2 Engine Control AssySPRING, Throttle Return ARM, GovernorROD, Governor SPRING, GovernorCrankcase Cover Assy Honda GX390K1QWT2 Engine Crankcase AssyGASKET, Case Cover WEIGHT, GovernorHOLDER, Governor Weight PIN, Governor WeightCrankshaft Assy Honda GX390K1QWT2 Engine Crankshaft AssyWEIGHT, Balancer Cylinder Barrel Assy Honda GX390K1QWT2 Engine Cylinder Barrel AssyOIL Seal Switch ASSY., OIL LevelSHAFT, Governor ARM BOLT, Drain PlugCylinder Head Assy Honda GX390K1QWT2 Engine Cylinder Head AssyCOVER, Head GUIDE, Valve OS OptionalCLIP, Valve Guide GASKET, Cylinder HeadFAN Cover Assy Honda GX390K1QWT2 Engine FAN Cover AssyShroud Switch ASSY., Engine StopCLIP, Tube COVER, FAN *NH1* BlackFlywheel Assy Honda GX390K1QWT2 Engine Flywheel AssyFlywheel FAN, CoolingNUT, Special 16MM Fuel Tank Assy Honda GX390K1QWT2 Engine Fuel Tank AssyGASKET, Fuel Filler CAP RUBBER, Supporter 107MMJOINT, Fuel Tank TANK, Fuel *NH1* BlackIgnition Coil Assy Honda GX390K1QWT2 Engine Ignition Coil AssyCoil ASSY., Ignition GROMMET, WireWIRE, Stop Switch 430MM CLIP, Wire HarnessMuffler 1 Assy Honda GX390K1QWT2 Engine Muffler AssyCAP, Muffler MufflerPROTECTOR, Muffler PIPE, EXPiston Assy Honda GX390K1QWT2 Engine Piston AssyPiston STD BOLT, Connecting RODRing SET, Piston STD Ring SET, Piston 0.75 NipponRecoil Starter Assy Honda GX390K1QWT2 Engine Recoil Stater AssySPRING, Starter Return PULLEY, Recoil StarterRATCHET, Starter SPRING, FrictionLabels Assy Honda GX390K1QWT2 Engine Labels AssyLABEL, Caution LABEL, AIR Cleaner CautionMARK, AIR Cleaner Sales Point EmblemFreight Policy Terms and Conditions of Sale PartsSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 HERE’S HOW to GET Help