Multiquip SP2S13H20A General Transmission Care, Transmission Reservoir Cup, Spline GearWheels

Page 33

MAINTENANCE

General Transmission Care

All SP2S13H20A model saws utilize spline gear wheel design coupled with an EATON Model 7 Hydrostatic Transmission that provides forward/reverse propulsion. The simple design of the system keeps maintenance to a minimum.

Transmission Reservoir Cup:

Check every 8 hours of operation. When the transmission is cold (A), check oil level against the level indicator (see Figure 45).

CAUTION

DO NOT use multiple viscosity oils! DO NOT OVERFILL.

Spline GearWheels:

Check every 25 hours and clean as necessary. If the spline wheels DO NOT engage the rear wheels with sufficient pressure, slippage of the rear wheels may occur.

To adjust the Spline Gear Assembly:

1.Place the transmission engage/disengage lever in the DISENGAGE position (Figure 46) .

Figure 45. Transmission Reservoir

Servicing:

Thetransmissionreservoiris factoryfilled.Shouldservicing berequired,useSAE20W-20,APIclassification(SE,CC,CD) or better, General Motors Dexron B, Ford M2C-33F, M2C- 41A or International Harvester Hy-Tran fluids. For extreme hot weather, drain oil and refill with an oil having a viscosity of SAE30W-30 or SAE40W-40.

Drive Chain:

Checkevery50hours. Periodicallywipethechaincleanand re-lubricate with penetrating chain oil.

The drive chain may stretch requiring tension adjustments. To adjust the drive chain tension:

1.Loosenthe(3)transmissionattachmentscrews(Hydrostatic. Transmission Assy., item 2)

2.Pivot the transmission in the“U”slots of the transmission mount until the proper tension is achieved (Hydrostatic Transmission Assy., item 7).

NOTE

Excessivetensiononthedrivechain will reduce chain life.

Figure 46. Transmission Engage/Disengage Lever

(Disengage Position)

3.Loosenthelinkageadjustmentnutandslightlylengthenthe linkagerod(seeTransmissionEngageLeverAssy.,items11 and 13).

4.Move the transmission engage/disengage lever to the ENGAGEpositiontoobservetheproperspline-to-rearwheel contact.

5.Retighten the adjustment nut.

SP2S13H20A SAW — OPERATION AND PARTS MANUAL — REV. #1 (05/17/10) — PAGE 33

Image 33

Contents Model SP2S13H20A Proposition 65 Warning Respiratory Hazards SILICOSIS/RESPIRATORY Warnings Silicosis WarningTable of Contents Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only Speciﬁcations SpecificationsSP2S13H20A Dimensions DimensionsIf you do not follow these directions Safety Message Alert SymbolsAlways wear approved eye and hearing protection Always wear approved respiratory protectionRules for Safe Operation Rules for Safe OperationDiamond Blade Safety General SafetySaw Transportation Safety Maintenance SafetyEmergencies  Always know the location of the nearest first aid kitSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 SP2S13H20A Saw Major Components Major Components13HP Honda Engine Components Cannister to gain access to filter elementSmoothly Flow of fuelGeneral Information SP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Before Starting InspectionEngine Oil Check Honda 13 HP engine shownAdditionally, when connecting the positive Hydrostatic TransmissionUse only distilled water Rotation downcuts with the turn of the shaft Inspection -BLADEOr others in the operating area Poor performance and/or blade damageSet the engine ON/OFF switch to the OFF position Inspection Blade PlacementFlange Inner flange collarGuards and Covers Check Inspection -GUARDS, Covers & BeltsInstitute Ansi B7.1 and B7.5 Belts Alignment and TensioningReplacement part numbers Inspection Belts & Water TankWater Tank Fuel Valve Lever Manual START-UPBlade operating speeds Started repeat steps 1 throughAssociate with a loose guard and/or covers  do not pull the starter rope all the way to the endSHUT-DOWN Procedures Stopping the Engine 13 HP Honda EnginePlace the fuel valve lever to the OFF position SP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Adjusting the Blade Height Adjusting the Handle BarsWhen moving the saw around OperationTraveling During Cutting Place the travel lever in the Neutral positionEngage Position Wet Cutting Operation CuttingTurn water source on Figure Follow steps 1-4 of the Traveling During Cutting sectionFinishing a Cut Extreme heat Diamond BladesBlade Speed Maintenance General Transmission Care Retighten the adjustment nutTransmission Reservoir Cup Spline GearWheelsAdjustV-Belt Alignment/Replacement Pulleys DriveV-Belt CheckLoosen the 4 1-1/2 HHC screws Engine Mount Assy., item Reference & for steps Blade Shaft Bearing ReplacementBattery Electrolyte Levels Battery MaintenanceHP Honda Engine Wiring Diagram 13HP Engine Wiring Diagram Recoil StartEngine Troubleshooting Troubleshooting EngineEngine Troubleshooting Blade Troubleshooting Troubleshooting BladeSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Xxxxx only Not Used on Explanation of Code in Remarks ColumnDescription Suggested Spare PartsName Plate and Decals Name Plate and DecalsDECAL, Multiquip DECAL, Recommended MaintenanceDECAL, SP2S13H20A DECAL, FORWARD/REVERSE LeverUnder Carriage Assy Under Carriage AssyFRAME, Undercarriagee Assy AXLE, Rear & FrontWASHER, Flat SAE 3/4 Bearing PlainBlade Shaft Assy Blade Shaft AssyFLANGE, Blade Inside 4.0OD X 1.0ID SPINDLE, BladeKEY, Woodruff #15 NUT, HEX JAM LH 1-14 PlatedLifting Bale Assy Lifting Bale Assy20HP, Lift Bail Assy 13HP, Lift Bale AssyBRACE, 13HP Bail BRACE, 20HP BailConsole Assy Console AssyHandle Assy Housing ASSY. REDGRIP, 1 ID WASHER, Lock 3/8 MED13HP Honda Engine Mount Assy 13HP Honda Engine Mount AssyEngine Base Assy NUT, HEX Finish 1/2-13Engine Assy See Blade Shaft Assy See Hydrostatic Drive Assy Engine AssyPart Name QTY. Remarks Engine AssyPointers and Covers Assy Pointers and Covers AssyBlade Guide Weldment Pointer and Covers AssySpanner Bushing CSI PointerWater System Assy Water System AssyFITTING, Nipple 1/2MP X 2 Galv FITTING, Plastic 90 1/2MP X 1/2BARBBolt W/NUTS FITTING, Brass 1/2 Barb X 3/4 GrdnBlade Guard Assy Blade Guard AssyBlade Guard W/A RED Connector 3/8GUARD, Splash Blade Spring TENSION, Guard BladeManual Raise and Lower Assy Manual Raise and Lower AssyJackpost Assy Jack Screw Assy BladeJackscrew BEARING, FlangeBattery Assy Battery AssyBattery Hold Down KIT Bracket BatterySTRAP, Ground NUT, HEX Finish 5/16-18Transmission Engage Lever Assy Transmission Engage Lever AssyWASHER, Flat SAE 3/8 HYD. Transmission Engage Lever AssyHydrostatic Transmission Hydrostatic Transmission AssyHydrostatic Transmission Assy Hydrostatic Drive Assy Hydrostatic Drive AssyCHAIN, Roller .375 Pitch X AIR Cleaner Assy Honda GX390K1QWT2 Engine AIR Cleaner AssyGROMMET, AIR Cleaner SEAL, AIR Cleaner CoverCOLLAR, AIR Cleaner Collar B, AIR CleanerCamshaft Assy Honda GX390K1QWT2 Engine Camshaft AssyROD, Push SPRING, Weight ReturnARM, Valve Rocker LIFTER, ValveCarburetor Assy Honda GX390K1QWT2 Engine Carburetor AssyGasket SET PLATE, Lever SettingValve SET, Float Float SETControl Assy Honda GX390K1QWT2 Engine Control AssyROD, Governor ARM, GovernorSPRING, Governor SPRING, Throttle ReturnCrankcase Cover Assy Honda GX390K1QWT2 Engine Crankcase AssyHOLDER, Governor Weight WEIGHT, GovernorPIN, Governor Weight GASKET, Case CoverCrankshaft Assy Honda GX390K1QWT2 Engine Crankshaft AssyWEIGHT, Balancer Cylinder Barrel Assy Honda GX390K1QWT2 Engine Cylinder Barrel AssySHAFT, Governor ARM Switch ASSY., OIL LevelBOLT, Drain Plug OIL SealCylinder Head Assy Honda GX390K1QWT2 Engine Cylinder Head AssyCLIP, Valve Guide GUIDE, Valve OS OptionalGASKET, Cylinder Head COVER, HeadFAN Cover Assy Honda GX390K1QWT2 Engine FAN Cover AssyCLIP, Tube Switch ASSY., Engine StopCOVER, FAN *NH1* Black ShroudFlywheel Assy Honda GX390K1QWT2 Engine Flywheel AssyFAN, Cooling FlywheelNUT, Special 16MM Fuel Tank Assy Honda GX390K1QWT2 Engine Fuel Tank AssyJOINT, Fuel Tank RUBBER, Supporter 107MMTANK, Fuel *NH1* Black GASKET, Fuel Filler CAPIgnition Coil Assy Honda GX390K1QWT2 Engine Ignition Coil AssyWIRE, Stop Switch 430MM GROMMET, WireCLIP, Wire Harness Coil ASSY., IgnitionMuffler 1 Assy Honda GX390K1QWT2 Engine Muffler AssyPROTECTOR, Muffler MufflerPIPE, EX CAP, MufflerPiston Assy Honda GX390K1QWT2 Engine Piston AssyRing SET, Piston STD BOLT, Connecting RODRing SET, Piston 0.75 Nippon Piston STDRecoil Starter Assy Honda GX390K1QWT2 Engine Recoil Stater AssyRATCHET, Starter PULLEY, Recoil StarterSPRING, Friction SPRING, Starter ReturnLabels Assy Honda GX390K1QWT2 Engine Labels AssyMARK, AIR Cleaner Sales Point LABEL, AIR Cleaner CautionEmblem LABEL, CautionFreight Policy Terms and Conditions of Sale PartsSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 HERE’S HOW to GET Help