Multiquip SP2S13H20A manual Inspection -BLADE, Rotation downcuts with the turn of the shaft

Page 20

INSPECTION -BLADE

WARNING

Failure to thoroughly inspect the diamond blade (Figure 11) for operational safety could result in damage to the blade, the saw, and may cause injury to the user or others in the operating area.

Figure 11. Diamond Blade

1. Drive Pin Hole – A commonly located hole on the diamond blade core that prevents operational blade slippage between the inner & outer blade flanges (collars). Inspect the diameter of the hole to ensure there is no distortion, and that a snug fit develops between the hole and drive pin.

2. Stress Relief Holes (Gullets) – Check the steel core for cracks that may have propagated from the slots and/or gullets. Cracks indicate extreme fatigue failure and if sawing continues, catastrophic failure will occur.

3. Edge Of The Steel Core – Check the diameter edge for discoloration (blue oxidation) indicating an overheating condition caused by insufficient cooling water/air. Overheating of blades may lead to loss of core tension and/or increase the possibility for blade failure. Check to make sure the steel core’s width is uniform about the rim of the blade, and not succumbing to an “under cutting” condition brought about by highly abrasive material or improper under cutting core protection.

4. Directional Arrow – Check to ensure that the blade is oriented properly on the blade shaft for sawing. Reference the directional arrow in the blade and place it so the direction

 

of rotation “downcuts” with the turn of the shaft.

5.

Diamond Segment or Rim – Ensure there are no cracks,

 

dings, or missing portions of the diamond segment/rim.

 

DO NOT use a blade that is missing a segment or a

 

portion of the rim. Damaged and/or missing segments/

 

rims may cause damage to your saw, and injury to the user

 

or others in the operating area.

6.

Specifications – Ensure that the blade specifications, size,

 

and diameter properly match up to the sawing operation.

 

Wet blades must have water to act as a coolant. Utilizing a

 

diamond blade not matched properly to the task may result

 

in poor performance and/or blade damage.

7.

Arbor Hole – It is essential that the arbor hole diameter

 

properly matches the blade, and that it is free from

 

distortions. Correct blade flanges (collars) must be used.

 

The inside face of the flanges must be clean & free of debris.

 

An out of round arbor condition will cause damage to the

 

blade and the saw.

8. MAX RPM – This RPM reference is the maximum safe operating speed for the blade selected. NEVER exceed the max RPM on the diamond blade. Exceeding the MAX RPM is dangerous, and may cause poor performance and may damage the blade.

PAGE 20 — SP2S13H20A SAW — OPERATION AND PARTS MANUAL — REV. #1 (05/17/10)

Image 20
Contents Model SP2S13H20A Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents Order via Fax Dealers Only Parts Ordering ProceduresBest Deal! Order via Internet Dealers Only Specifications SpecificationsDimensions SP2S13H20A DimensionsSafety Message Alert Symbols If you do not follow these directionsAlways wear approved respiratory protection Always wear approved eye and hearing protectionRules for Safe Operation Rules for Safe OperationGeneral Safety Diamond Blade SafetyMaintenance Safety Saw Transportation SafetyEmergencies  Always know the location of the nearest first aid kitSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Major Components SP2S13H20A Saw Major ComponentsCannister to gain access to filter element 13HP Honda Engine ComponentsSmoothly Flow of fuelGeneral Information SP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Inspection Before StartingEngine Oil Check Honda 13 HP engine shownUse only distilled water Additionally, when connecting the positiveHydrostatic Transmission Inspection -BLADE Rotation downcuts with the turn of the shaftOr others in the operating area Poor performance and/or blade damageInspection Blade Placement Set the engine ON/OFF switch to the OFF positionFlange Inner flange collarInspection -GUARDS, Covers & Belts Guards and Covers CheckInstitute Ansi B7.1 and B7.5 Belts Alignment and TensioningWater Tank Replacement part numbersInspection Belts & Water Tank Manual START-UP Fuel Valve LeverStarted repeat steps 1 through Blade operating speedsAssociate with a loose guard and/or covers  do not pull the starter rope all the way to the endPlace the fuel valve lever to the OFF position SHUT-DOWN ProceduresStopping the Engine 13 HP Honda Engine SP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Adjusting the Handle Bars Adjusting the Blade HeightWhen moving the saw around OperationEngage Position Traveling During CuttingPlace the travel lever in the Neutral position Cutting Wet Cutting OperationTurn water source on Figure Follow steps 1-4 of the Traveling During Cutting sectionBlade Speed Finishing a CutExtreme heat Diamond Blades Maintenance Retighten the adjustment nut General Transmission CareTransmission Reservoir Cup Spline GearWheelsLoosen the 4 1-1/2 HHC screws Engine Mount Assy., item AdjustV-Belt Alignment/Replacement PulleysDriveV-Belt Check Blade Shaft Bearing Replacement Reference & for stepsBattery Maintenance Battery Electrolyte Levels13HP Engine Wiring Diagram Recoil Start HP Honda Engine Wiring DiagramTroubleshooting Engine Engine TroubleshootingEngine Troubleshooting Troubleshooting Blade Blade TroubleshootingSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Explanation of Code in Remarks Column Xxxxx only Not Used onSuggested Spare Parts DescriptionName Plate and Decals Name Plate and DecalsDECAL, Recommended Maintenance DECAL, MultiquipDECAL, SP2S13H20A DECAL, FORWARD/REVERSE LeverUnder Carriage Assy Under Carriage AssyAXLE, Rear & Front FRAME, Undercarriagee AssyWASHER, Flat SAE 3/4 Bearing PlainBlade Shaft Assy Blade Shaft AssySPINDLE, Blade FLANGE, Blade Inside 4.0OD X 1.0IDKEY, Woodruff #15 NUT, HEX JAM LH 1-14 PlatedLifting Bale Assy Lifting Bale Assy13HP, Lift Bale Assy 20HP, Lift Bail AssyBRACE, 13HP Bail BRACE, 20HP BailConsole Assy Console AssyHousing ASSY. RED Handle AssyGRIP, 1 ID WASHER, Lock 3/8 MED13HP Honda Engine Mount Assy 13HP Honda Engine Mount AssyNUT, HEX Finish 1/2-13 Engine Base AssyEngine Assy Engine Assy See Blade Shaft Assy See Hydrostatic Drive AssyEngine Assy Part Name QTY. RemarksPointers and Covers Assy Pointers and Covers AssyPointer and Covers Assy Blade Guide WeldmentSpanner Bushing CSI PointerWater System Assy Water System AssyFITTING, Plastic 90 1/2MP X 1/2BARB FITTING, Nipple 1/2MP X 2 GalvBolt W/NUTS FITTING, Brass 1/2 Barb X 3/4 GrdnBlade Guard Assy Blade Guard AssyConnector 3/8 Blade Guard W/A REDGUARD, Splash Blade Spring TENSION, Guard BladeManual Raise and Lower Assy Manual Raise and Lower AssyJack Screw Assy Blade Jackpost AssyJackscrew BEARING, FlangeBattery Assy Battery AssyBracket Battery Battery Hold Down KITSTRAP, Ground NUT, HEX Finish 5/16-18Transmission Engage Lever Assy Transmission Engage Lever AssyHYD. Transmission Engage Lever Assy WASHER, Flat SAE 3/8Hydrostatic Transmission Assy Hydrostatic TransmissionHydrostatic Transmission Assy Hydrostatic Drive Assy Hydrostatic Drive AssyCHAIN, Roller .375 Pitch X Honda GX390K1QWT2 Engine AIR Cleaner Assy AIR Cleaner AssySEAL, AIR Cleaner Cover GROMMET, AIR CleanerCOLLAR, AIR Cleaner Collar B, AIR CleanerHonda GX390K1QWT2 Engine Camshaft Assy Camshaft AssySPRING, Weight Return ROD, PushARM, Valve Rocker LIFTER, ValveHonda GX390K1QWT2 Engine Carburetor Assy Carburetor AssyPLATE, Lever Setting Gasket SETValve SET, Float Float SETHonda GX390K1QWT2 Engine Control Assy Control AssyARM, Governor ROD, GovernorSPRING, Governor SPRING, Throttle ReturnHonda GX390K1QWT2 Engine Crankcase Assy Crankcase Cover AssyWEIGHT, Governor HOLDER, Governor WeightPIN, Governor Weight GASKET, Case CoverHonda GX390K1QWT2 Engine Crankshaft Assy Crankshaft AssyWEIGHT, Balancer Honda GX390K1QWT2 Engine Cylinder Barrel Assy Cylinder Barrel AssySwitch ASSY., OIL Level SHAFT, Governor ARMBOLT, Drain Plug OIL SealHonda GX390K1QWT2 Engine Cylinder Head Assy Cylinder Head AssyGUIDE, Valve OS Optional CLIP, Valve GuideGASKET, Cylinder Head COVER, HeadHonda GX390K1QWT2 Engine FAN Cover Assy FAN Cover AssySwitch ASSY., Engine Stop CLIP, TubeCOVER, FAN *NH1* Black ShroudHonda GX390K1QWT2 Engine Flywheel Assy Flywheel AssyNUT, Special 16MM FAN, CoolingFlywheel Honda GX390K1QWT2 Engine Fuel Tank Assy Fuel Tank AssyRUBBER, Supporter 107MM JOINT, Fuel TankTANK, Fuel *NH1* Black GASKET, Fuel Filler CAPHonda GX390K1QWT2 Engine Ignition Coil Assy Ignition Coil AssyGROMMET, Wire WIRE, Stop Switch 430MMCLIP, Wire Harness Coil ASSY., IgnitionHonda GX390K1QWT2 Engine Muffler Assy Muffler 1 AssyMuffler PROTECTOR, MufflerPIPE, EX CAP, MufflerHonda GX390K1QWT2 Engine Piston Assy Piston AssyBOLT, Connecting ROD Ring SET, Piston STDRing SET, Piston 0.75 Nippon Piston STDHonda GX390K1QWT2 Engine Recoil Stater Assy Recoil Starter AssyPULLEY, Recoil Starter RATCHET, StarterSPRING, Friction SPRING, Starter ReturnHonda GX390K1QWT2 Engine Labels Assy Labels AssyLABEL, AIR Cleaner Caution MARK, AIR Cleaner Sales PointEmblem LABEL, CautionTerms and Conditions of Sale Parts Freight PolicySP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 HERE’S HOW to GET Help