Multiquip SP2S13H20A manual Wet Cutting Operation, Turn water source on Figure

Page 30

OPERATION

Cutting

WARNING

The operator MUST wear the appropriate protective

equipment and clothing while engaged in sawing. Failure to do so can result in SERIOUS INJURY.

DANGER

DONOToperate this machine without the Blade Guard or V-belt Guards in place.While the blade is spinning, DO NOT place hands, feet, or other body parts near the blade to avoid SERIOUS INJURY or DEATH.

When cutting, determine the required cutting depth and use an appropriately sized blade. Deep sawing is wasteful to the life of the blade.

The preferred method of sawing is to Step Cut in increments of 2”(51mm). StepCuttingprovidestheoptimumopportunityforthe blade to cut fast and last longest.

Wet Cutting Operation

1.Connect hose from water source (on-board water tank or external water source) to the hose fitting connection (Figure 3) of the saw. The source pressure should be approximately 30-40 psi.

2.Ensure the vinyl water tubes are properly inserted into the blade guard holes and are clear of any obstructions.

3.Turn water source on (Figure 43).

Figure 44.Water System ON/OFFValve

5. Align the saw along the cut line utilizing the front pointer.

CAUTION

ALWAYS saw in a straight line only. SERIOUS DAMAGE to the blade or saw may occur if the saw is twisted or forced to cut radius shapes.

6.Slowlylowerthediamondbladeontothecutlinebycranking the Raise/LowerhandleCLOCKWISE (Figure 37). When the handle can no longer be turned, theblade will be at its full rated depth.

WARNING

If the water supply to your blade is interrupted, STOP cutting immediately to prevent damage to your blade and/or saw.

If the engine stalls for ANY reason during cutting, raise the blade out of the cut before restarting.

7.Follow steps 1-4 of the Traveling During Cutting section.

8.The rotation of the blade creates a tendency for the saw to slightly pull in a particular direction. To ensure a straight line of sawing, apply pressure against the appropriate side of the handle bar as you slowly advance the saw forward.

Figure 43. On-board Water Tank ON/OFF Valve

4.Open the watersystemvalveon the left side of the console bymovingthelevertotheONposition(Figure44)andensure the water is flowing equally to both sides of the diamond blade.

CAUTION

DO NOT force the blade into the cut any faster than its design will allow. This can damage your blade and/or your machine.

Dry Cutting Operation

When dry cutting, follow steps 5-8 of theWetCuttingOperation section.

PAGE 30 — SP2S13H20A SAW — OPERATION AND PARTS MANUAL — REV. #1 (05/17/10)

Image 30
Contents Model SP2S13H20A Proposition 65 Warning SILICOSIS/RESPIRATORY Warnings Silicosis Warning Respiratory HazardsTable of Contents Parts Ordering Procedures Best Deal! Order via Internet Dealers OnlyOrder via Fax Dealers Only Specifications SpecificationsDimensions SP2S13H20A DimensionsSafety Message Alert Symbols If you do not follow these directionsAlways wear approved respiratory protection Always wear approved eye and hearing protectionRules for Safe Operation Rules for Safe OperationGeneral Safety Diamond Blade SafetyEmergencies Maintenance SafetySaw Transportation Safety  Always know the location of the nearest first aid kitSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Major Components SP2S13H20A Saw Major ComponentsSmoothly Cannister to gain access to filter element13HP Honda Engine Components Flow of fuelGeneral Information SP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Engine Oil Check InspectionBefore Starting Honda 13 HP engine shownAdditionally, when connecting the positive Hydrostatic TransmissionUse only distilled water Or others in the operating area Inspection -BLADERotation downcuts with the turn of the shaft Poor performance and/or blade damageFlange Inspection Blade PlacementSet the engine ON/OFF switch to the OFF position Inner flange collarInstitute Ansi B7.1 and B7.5 Inspection -GUARDS, Covers & BeltsGuards and Covers Check Belts Alignment and TensioningReplacement part numbers Inspection Belts & Water TankWater Tank Manual START-UP Fuel Valve LeverAssociate with a loose guard and/or covers Started repeat steps 1 throughBlade operating speeds  do not pull the starter rope all the way to the endSHUT-DOWN Procedures Stopping the Engine 13 HP Honda EnginePlace the fuel valve lever to the OFF position SP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 When moving the saw around Adjusting the Handle BarsAdjusting the Blade Height OperationTraveling During Cutting Place the travel lever in the Neutral positionEngage Position Turn water source on Figure CuttingWet Cutting Operation Follow steps 1-4 of the Traveling During Cutting sectionFinishing a Cut Extreme heat Diamond BladesBlade Speed Maintenance Transmission Reservoir Cup Retighten the adjustment nutGeneral Transmission Care Spline GearWheelsAdjustV-Belt Alignment/Replacement Pulleys DriveV-Belt CheckLoosen the 4 1-1/2 HHC screws Engine Mount Assy., item Blade Shaft Bearing Replacement Reference & for stepsBattery Maintenance Battery Electrolyte Levels13HP Engine Wiring Diagram Recoil Start HP Honda Engine Wiring DiagramTroubleshooting Engine Engine TroubleshootingEngine Troubleshooting Troubleshooting Blade Blade TroubleshootingSP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 Explanation of Code in Remarks Column Xxxxx only Not Used onSuggested Spare Parts DescriptionName Plate and Decals Name Plate and DecalsDECAL, SP2S13H20A DECAL, Recommended MaintenanceDECAL, Multiquip DECAL, FORWARD/REVERSE LeverUnder Carriage Assy Under Carriage AssyWASHER, Flat SAE 3/4 AXLE, Rear & FrontFRAME, Undercarriagee Assy Bearing PlainBlade Shaft Assy Blade Shaft AssyKEY, Woodruff #15 SPINDLE, BladeFLANGE, Blade Inside 4.0OD X 1.0ID NUT, HEX JAM LH 1-14 PlatedLifting Bale Assy Lifting Bale AssyBRACE, 13HP Bail 13HP, Lift Bale Assy20HP, Lift Bail Assy BRACE, 20HP BailConsole Assy Console AssyGRIP, 1 ID Housing ASSY. REDHandle Assy WASHER, Lock 3/8 MED13HP Honda Engine Mount Assy 13HP Honda Engine Mount AssyNUT, HEX Finish 1/2-13 Engine Base AssyEngine Assy Engine Assy See Blade Shaft Assy See Hydrostatic Drive AssyEngine Assy Part Name QTY. RemarksPointers and Covers Assy Pointers and Covers AssySpanner Bushing CSI Pointer and Covers AssyBlade Guide Weldment PointerWater System Assy Water System AssyBolt W/NUTS FITTING, Plastic 90 1/2MP X 1/2BARBFITTING, Nipple 1/2MP X 2 Galv FITTING, Brass 1/2 Barb X 3/4 GrdnBlade Guard Assy Blade Guard AssyGUARD, Splash Blade Connector 3/8Blade Guard W/A RED Spring TENSION, Guard BladeManual Raise and Lower Assy Manual Raise and Lower AssyJackscrew Jack Screw Assy BladeJackpost Assy BEARING, FlangeBattery Assy Battery AssySTRAP, Ground Bracket BatteryBattery Hold Down KIT NUT, HEX Finish 5/16-18Transmission Engage Lever Assy Transmission Engage Lever AssyHYD. Transmission Engage Lever Assy WASHER, Flat SAE 3/8Hydrostatic Transmission Assy Hydrostatic TransmissionHydrostatic Transmission Assy Hydrostatic Drive Assy Hydrostatic Drive AssyCHAIN, Roller .375 Pitch X Honda GX390K1QWT2 Engine AIR Cleaner Assy AIR Cleaner AssyCOLLAR, AIR Cleaner SEAL, AIR Cleaner CoverGROMMET, AIR Cleaner Collar B, AIR CleanerHonda GX390K1QWT2 Engine Camshaft Assy Camshaft AssyARM, Valve Rocker SPRING, Weight ReturnROD, Push LIFTER, ValveHonda GX390K1QWT2 Engine Carburetor Assy Carburetor AssyValve SET, Float PLATE, Lever SettingGasket SET Float SETHonda GX390K1QWT2 Engine Control Assy Control AssySPRING, Governor ARM, GovernorROD, Governor SPRING, Throttle ReturnHonda GX390K1QWT2 Engine Crankcase Assy Crankcase Cover AssyPIN, Governor Weight WEIGHT, GovernorHOLDER, Governor Weight GASKET, Case CoverHonda GX390K1QWT2 Engine Crankshaft Assy Crankshaft AssyWEIGHT, Balancer Honda GX390K1QWT2 Engine Cylinder Barrel Assy Cylinder Barrel AssyBOLT, Drain Plug Switch ASSY., OIL LevelSHAFT, Governor ARM OIL SealHonda GX390K1QWT2 Engine Cylinder Head Assy Cylinder Head AssyGASKET, Cylinder Head GUIDE, Valve OS OptionalCLIP, Valve Guide COVER, HeadHonda GX390K1QWT2 Engine FAN Cover Assy FAN Cover AssyCOVER, FAN *NH1* Black Switch ASSY., Engine StopCLIP, Tube ShroudHonda GX390K1QWT2 Engine Flywheel Assy Flywheel AssyFAN, Cooling FlywheelNUT, Special 16MM Honda GX390K1QWT2 Engine Fuel Tank Assy Fuel Tank AssyTANK, Fuel *NH1* Black RUBBER, Supporter 107MMJOINT, Fuel Tank GASKET, Fuel Filler CAPHonda GX390K1QWT2 Engine Ignition Coil Assy Ignition Coil AssyCLIP, Wire Harness GROMMET, WireWIRE, Stop Switch 430MM Coil ASSY., IgnitionHonda GX390K1QWT2 Engine Muffler Assy Muffler 1 AssyPIPE, EX MufflerPROTECTOR, Muffler CAP, MufflerHonda GX390K1QWT2 Engine Piston Assy Piston AssyRing SET, Piston 0.75 Nippon BOLT, Connecting RODRing SET, Piston STD Piston STDHonda GX390K1QWT2 Engine Recoil Stater Assy Recoil Starter AssySPRING, Friction PULLEY, Recoil StarterRATCHET, Starter SPRING, Starter ReturnHonda GX390K1QWT2 Engine Labels Assy Labels AssyEmblem LABEL, AIR Cleaner CautionMARK, AIR Cleaner Sales Point LABEL, CautionTerms and Conditions of Sale Parts Freight PolicySP2S13H20A SAW Operation and Parts Manual REV. #1 05/17/10 HERE’S HOW to GET Help