Multiquip MT85HS operation manual Fuel and OIL Lines

Page 17

MAINTENANCE

2.Removetheboltsthatsecuretheoiltanktothefueltank,and drain all oil from the tank.

3.Remove cock holder, then clean strainer and cock holder in a kerosene solution.

4.Make sure every part is clean and dry, then reassemble oil tank. Fill oil tank with 2-stroke outboard motor oil (FB class) to the "H" level.

FUEL AND OIL LINES

■Check the fuel and oil lines regularly for damage and ensure that there are no leaks.

■Replace fuel and oil lines every 2 years to maintain performance.

■When replacing the oil hose perform the following procedure:

1.Replaceoilhosewithmanufacturessuggestedtypehoseor equivalent.

2.If necessary, fill oil tank with 2-stroke outboard motor oil.

3.Fill fuel tank with 25:1 fuel mix ratio.

4.Operaterammerwith25:1fuelmixtureuntilallairisbledfrom oil injection line.

5.Once it is certain that all air has been purged from the oil injection line, regular unleaded gasoline may be used.

CAUTION:

It is normal for a new 2-stroke engine to emit excess smoke, until moving parts have been seatedtotheirnormaloperatingspecifications. Thisexcesssmokenormallystopsafteronefull tank of fuel.

■The air cleaner (Figure 12) on the engine side will hardly be contaminated, if it is, however after cleaning the element with kerosene, dip it in mixed oil consisting of 3 parts of gasoline and 1 part of engine oil.Then tightly squeeze outer primary element (sponge) and shake off well the inner secondary element before installing them.

CLEANINGTHERAMMER

■If using a high pressure spray washer, be careful not to splash water directly on the air cleaner, carburetor, muffler, fuel and oil tank caps. Excessive amounts of water may cause severe engine damage.

Yearly

■Check the fuel line and the oil line regularly for damage and to ensure that there are no leaks.

■Replace the oil and fuel lines every two years to maintain the performance and flexibility lines.

Long Term Storage

■Drain fuel from fuel tank, fuel line and carburetor.

■Remove spark plug and pour a few drops of motor oil into cylinder. Crank engine 3 to 4 times so that oil reaches all internal parts.

■Clean exterior of rammer with an oil-moistened cloth.

■Store unit covered with plastic sheet in moisture free and dust free location out of direct sunlight

200 - 300 HOURS (Oil Bath)

■Drain oil reservoir on foot housing (Figure 13). Refill with approximately 1.7 pt. (800cc) of 10W-30 motor oil. Oil should be midway in sight glass. Break in oil should be changed after first 50 hours.

Figure 13. Oil Drain Plug

Figure 12. Air Cleaner

MT85HS RAMMER — OPERATION AND PARTS MANUAL — REV. #9 (01/16/12) — PAGE 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model MT85HS Proposition 65 Warning MT85HS Rammer Operation and Parts Manual REV. #9 01/16/12 MT85HS Rammer Robin EC12HS Engine Table of ContentsOrdering parts has never been easier Parts Ordering ProceduresSafety Messages Safety InformationGeneral Safety Engine Safety Transporting Safety Definition of Tamping Rammer General InformationSpecifications MT-85HS Rammer SpecificationsMT-85HS Rammer ComponentsRammer Gearbox and Spring Cylinder Oil Bath Operation14 MT85HS Rammer Operation and Parts Manual REV. #9 01/16/12 Normal Shutdown Daily MaintenanceFuel and OIL Lines Engine Troubleshooting Symptom Possible Problem Solution TroubleshootingSymptom Possible Problem Solution Explanation of Codes in the Remarks Column Sample Parts ListTo 3 Units To 5 Units Suggested Spare PartsMikasa Nameplate and DecalsDecal PRE Cleaner Decal PRE-CLEANERDecal Switch ON-OFF Decal Switch onCrankcase and Engine Assy Throttle Wire Connecting RODBODY/W-CLEANER Crank CaseGuide Cylinder and Foot Assy Stop Ring R-15 Piston PINPiston ROD Piston ENDTank and Handle Assy Handle Roller Wire CPFuel Tank FILTER, Tank30 MT85HS Rammer Operation and Parts Manual REV. #9 01/16/12 Well NUT M5 STRAP, OIL TankWASHER, PW M5 GUARD, OIL HoseRobin EC12HS Engine Crankcase Assy OIL Seal VC OIL Seal EC13Ball Bearing 6205C3 Dowel PINRobin EC12HS Engine Crankshaft and Piston Assy Spacer 0.IT Crank Shaft AssySpacer 0.3T Spring WasherRobin EC12HS Engine Governor Assy Governor Lever Wire BracketGovernor Shaft Governor RODRobin EC12HS Engine MUFFLER/AIR Cleaner Assy Bracket Cleaner Gasket AIR CleanerMuffler Compl Muffler BracketRobin EC12HS Engine Carburetor Assy Throttle Valve AdjusterPilot JET SpringRobin EC12HS Engine Recoil Starter Assy Labelengine Name Cylinder BaffleTapping Bolt Spiral SpringRobin EC12HS Engine Electric Device Assy Flywheel Compl Wire 22 CPGROMMET, High Plug TerminalRobin EC12HS Engine Loose Parts Switch Float CP Freight Policy Terms and Condition of Sale PartsMT85HS Rammer Operation and Parts Manual REV. #9 01/16/12 HERE’S HOW to GET Help
Top Page Image Contents