Parkside PSTK 730 A1 manual General safety advice for electrical power tools, Electrical safety

Page 9

General safety advice for electrical power tools

2. Electrical safety

a)The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock.

b)Avoid touching earthed surfaces such as pipes, radiators, ovens and refrig- erators with any part of your body.

There is an increased risk of electric shock if your body is earthed.

c)Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock.

d)Do not use the mains lead for any purpose for which it was

not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device. Damaged or tangled mains leads increase the risk of electric shock.

e)When working outdoors with an electrical power tool always use ex- tension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock.

f)Use a residual current device (RCD) for protection if operating the electri- cal power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock.

3. Personal safety

a)Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury.

b)Wear personal protective equipment and always wear

safety glasses. The wearing of personal protective equipment such as dust masks, non-slip safety shoes, safety helmets or ear protectors, appropriate to the type of elec- trical power tool used and work undertaken, reduces the risk of injury.

c)Avoid unintentional operation of the device. Check that the electrical power tool is switched off before you connect it to the mains, pick it up or carry it. Accidents can happen if you carry the device with your finger on the ON / OFF switch or with the device switched on.

d)Remove any setting tools or spanners before you switch the device on. A tool or spanner left attached to a rotating part of a device can lead to injury.

e)Avoid placing your body in an unnat- ural position. Keep proper footing and balance at all times. By doing this you will be in a better position to control the device in unforeseen circumstances.

f)Wear suitable clothing. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves clear of mov- ing parts. Loose clothing, jewellery or long hair can become trapped in moving parts.

g)If vacuum dust extraction and collection devices are fitted do not forget to check that they are properly connected and correctly used. The use of these devices reduces the hazard presented by dust.

4.Careful handling and use of electrical power tools

a)Do not overload the device. Always use an electrical power tool that is intended for the task you are under- taking. By using the right electrical power tool for the job you will work more safely and achieve a better result.

b)Do not use an electrical power tool if its switch is defective. An electrical power

8

GB/IE

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Jigsaw Pstk 730 A1 GB / IE 13 12 10 9 10 mm 260 mm 70 mm 65 mm 30 mm 205 mm 110 mm 150 mm 10 mm 395 mm x 185 mm x 10 mm 395 mm x 120 mm x 10 mm Table of contents Introduction Features and equipmentJigsaw Pstk 730 A1 Proper useWorkplace safety Included itemsTechnical information Electrical safety General safety advice for electrical power toolsPersonal safety Careful handling and use of electrical power toolsDo not work on moistened materials or damp surfaces Safety advice relating specifically to this deviceInformation about saw blades Original accessories / attachmentsMounting / replacing saw blades Attaching the chip guardPreparing for use / Operation Cleaning MaintenanceService centre Warranty DisposalDisposal / Declaration of Conformity / Manufacturer Page Inhaltsverzeichnis Pendelhubstichsäge Pstk 730 A1 EinleitungAusstattung Bestimmungsgemäßer GebrauchLieferumfang Technische DatenArbeitsplatz-Sicherheit Elektrische Sicherheit Allgemeine Sicherheitshinweise für ElektrowerkzeugeSicherheit von Personen Zweckentfremden Sie das Kabel nicht, um das ElektroGerätespezifische Sicherheitshinweise für Pendelhubstichsägen Verwendung und Behandlung des ElektrowerkzeugsOriginalzubehör / -zusatzgeräte Informationen zu SägeblätternSägeblatt montieren / wechseln Sägeblattyp Für Pstk Ungeeignet A1 geeignetInbetriebnahme / Bedienung Einschalten / Ausschalten Bedienung / Wartung und Reinigung / Service / GarantieWartung ReinigungEntsorgung Entsorgung / Konformitätserklärung / HerstellerKonformitätserklärung Hersteller Werfen Sie Elektrowerkzeuge nicht in den HausmüllKompernass Gmbh

PSTK 730 A1 specifications

The Parkside PSTK 730 A1 is a versatile tool that has been designed to cater to various DIY enthusiasts and professionals. This multifunctional power tool stands out for its exceptional performance and a range of modern features that enhance its usability and efficiency.

One of the main features of the PSTK 730 A1 is its powerful motor, which delivers robust performance. With a power output of 730 Watts, this tool provides ample energy for a variety of tasks, including cutting, sanding, and polishing. The motor is complemented by an adjustable speed control, allowing users to select the optimal speed setting according to the material they are working with. This flexibility is crucial for achieving precise results, whether you are working with wood, metal, or plastic.

The tool is equipped with a quick-change system that allows for easy swapping of accessories without the need for additional tools. This feature significantly saves time and enhances workflow, particularly when changing tasks frequently. The PSTK 730 A1 comes with a range of accessories, including saw blades and sanding sheets, making it a truly multifunctional device ideal for various applications.

Another noteworthy characteristic of the Parkside PSTK 730 A1 is its ergonomic design. The tool is lightweight, which minimizes user fatigue during extended use. Its soft-grip handle ensures a comfortable grip, providing better control and maneuverability while operating. The design incorporates safety features such as a protective guard, ensuring that users can work with confidence.

In terms of technology, the PSTK 730 A1 utilizes advanced oscillation technology. This allows users to achieve precise cuts and clean finishes, even in tight spaces. The oscillating motion minimizes splintering and ensures a smooth surface, especially when working with delicate materials.

Furthermore, the tool features an integrated dust extraction system that helps keep the work area clean by effectively removing debris and dust generated during operation. This not only provides a clearer view of the work surface but also reduces the risk of inhalation hazards.

In conclusion, the Parkside PSTK 730 A1 is a dependable and adaptable tool that brings power, efficiency, and convenience to a range of DIY projects. Its array of features, from adjustable speed and quick accessory changes to its ergonomic design and built-in dust extraction, makes it an essential addition to any workshop or home toolkit for both professionals and hobbyists alike.
Top Page Image Contents