Grizzly G0592 owner manual Blade Guide Bearings, To adjust the blade guide bearings

Page 38

Blade Guide

Bearings

The blade guide bearings are adjusted at the fac- tory but may need adjustment depending on the use of your bandsaw. Use Figures 46 & 47 to

guide you through the following steps.

Guide Bearings

Cap Screws

Backing Bearing

Eccentric Bushing

Carbide Blade Guide

Figure 46. Blade guide adjustments.

To adjust the blade guide bearings:

1.Before making adjustments, make sure the blade is tensioned and tracking correctly.

2.DISCONNECT THE BANDSAW FROM POWER!

3.Lower the bow until it makes contact with the horizontal stop.

4.Remove the blade guides.

5.The back of the blade should make light con- tact with the backing bearing.

—If it does not, loosen the two cap screws shown in Figure 46. Lower the blade guide until the back of the blade makes light con- tact with the backing bearing. Then tighten the two cap screws.

6.Loosen the set screw in Figure 47 to allow the eccentric bushing to turn.

7.Turn the hex nut on the eccentric shaft to adjust the distance of the guide bearing. The guide bearings and blade should make light contact or have a maximum clearance of 0.002".

8.Adjust the other eccentric blade guide bear- ing in the same manner.

9.

Adjust the carbide blade guides so they make

 

the same contact with the blade as the bear-

 

ings.

Set Screw

Hex Nut

Figure 47. More blade guide adjustments.

-36-

G0592 Metal Cutting Bandsaw

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Model G0592 Page Table of Contents Maintenance Contact Info IntroductionForeword Machine Data Sheet Other Identification Control Panel Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Metal Cutting Bandsaws 220V Single-Phase Circuit RequirementsItems Needed for Set Up SET UPSet Up Safety UnpackingInventory Box 1 Figure QtyHardware Recognition Chart Clean Up Site ConsiderationsMoving & Placing Base Unit Mounting to Shop FloorWorkstop To install the workstopShipping Bracket To remove the shipping bracketFeed Stop To adjust the feed stop boltChip Trays & Splash Guard Components and Hardware Needed QtyTest Run Recommended AdjustmentsFactory adjustments that should be verified Vise Operation SafetyOperations To change vise positionsVise jaw positioning To rapidly change the vise jaw gapCutting Angle To change the angleTo change blade speeds Blade SelectionBlade Speed Feed Rate To set the feed rateCoolant System To adjust the rear blade guideBlade Guides To use the coolant systemSpray gun G0592 Metal Cutting Bandsaw Cutting Fluid Operation Tips Tips for horizontal cuttingG7897-Machining Fluid AccessoriesH5405-LenoxLube Tube H1300 H1298 G7984 H2347 H0736 H1302-Standard EarmuffsH1302 H4979 H4977 Schedule MaintenanceCleaning LubricationVise leadscrew lubrication area Service TroubleshootingBandsaw Operations Blade Change To change the blade on the bandsawTo tension the blade on the bandsaw To adjust the blade tracking on the bandsawBlade Tension Tracking To adjust the blade guide bearings Blade Guide BearingsLimit switch Electrical ComponentsTransformer Contactor Relay Terminal Block Model G0592 220V Wiring Diagram Parts Breakdown Base Parts List DescriptionSwivel Base Swivel Base Parts List Vise Parts Breakdown Vise Parts List Bow Parts Breakdown Bow Parts List Blade Tension Blade Tension & Motor Parts List PB87MBladeGuides Blade Guides Parts List Electrical Parts Electrical Parts List Warranty and Returns Page Page

G0592 specifications

The Grizzly G0592 is a high-performance milling machine designed to meet the demands of both professional and hobbyist woodworkers. Known for its robust construction and precise engineering, this machine combines versatility with durability, making it an essential tool for any woodworking shop.

One of the standout features of the G0592 is its powerful motor, which offers a significant amount of torque, enabling it to handle a variety of materials with ease. The machine is equipped with a 3 HP motor that operates on 220V single-phase power, providing consistent performance for heavy-duty milling tasks. This high power helps to minimize stalling or bogging down during operation, ensuring smooth and efficient cutting.

The G0592 also boasts a generous working table made from precision-ground cast iron, measuring 9” x 49”. This extensive surface area allows for the handling of larger workpieces and offers ample space for stock support. The table is fitted with T-slots, allowing for easy attachment of jigs, fixtures, and clamping tools, enhancing the versatility of the machine.

Another notable characteristic is its adjustable dovetail ways, which provide enhanced stability and precision during operation. This design helps in maintaining alignment and reduces wear on the machine over time. Additionally, the G0592 features a variable speed drive that allows users to adjust the spindle speed from 60 to 4,000 RPM, accommodating various cutting applications ranging from heavy milling to delicate engraving.

The head of the G0592 is also a significant aspect of its design. It can be swiveled up to 90 degrees, facilitating angular cuts and increasing the range of milling operations possible. Moreover, the machine includes a digital readout (DRO) for both the table and spindle positions, providing real-time feedback and enhanced accuracy during operations.

Safety features, such as an emergency stop button and a protective enclosure around the spindle, are integrated into the G0592 to ensure a safe working environment. Overall, the Grizzly G0592 is engineered for those who value precision and performance in their milling tasks, making it a reliable choice in both professional and amateur settings. Its robust build, ample features, and user-friendly design distinguish it as a leading option in the milling machine market.
Top Page Image Contents