Grizzly G0592 owner manual Blade Change, To change the blade on the bandsaw

Page 36

Blade Change

Blades should be changed when they become dull, damaged, or when you are using materials that require a blade of a certain type or tooth count.

To change the blade on the bandsaw:

1.DISCONNECT THE BANDSAW FROM POWER!

2.Raise the bow of the bandsaw to the highest position, close the feed control knob, and remove the wheel access cover.

3.Slide the blade guard all the way down as shown in Figure 41.

Tension Handle

Blade Guard

Figure 41. Tension handle and blade.

4.Remove the blade guard and wire wheel from the front of the bandsaw as shown in Figure 42.

CUTTING HAZARD! Blades are sharp! Wear heavy leather gloves when handling blades to prevent cuts.

-34-

Front Blade Guard

Figure 42. Removing front blade guard.

5.Loosen the blade tension handle in Figure 41 and slip the blade off of the wheels.

6.Install the new blade through both blade guide bearings, as shown in Figure 43, and around the bottom wheel.

Figure 43. Installing the blade.

7.Hold the blade around the bottom wheel with one hand and slip it around the top wheel with the other hand, keeping the blade between the blade guide bearings.

G0592 Metal Cutting Bandsaw

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Model G0592 Page Table of Contents Maintenance Introduction ForewordContact Info Machine Data Sheet Other Identification Control Panel Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Metal Cutting Bandsaws 220V Single-Phase Circuit RequirementsSET UP Set Up SafetyItems Needed for Set Up UnpackingInventory Box 1 Figure QtyHardware Recognition Chart Clean Up Site ConsiderationsMoving & Placing Base Unit Mounting to Shop FloorTo install the workstop Shipping BracketWorkstop To remove the shipping bracketTo adjust the feed stop bolt Chip Trays & Splash GuardFeed Stop Components and Hardware Needed QtyRecommended Adjustments Factory adjustments that should be verifiedTest Run Operation Safety OperationsVise To change vise positionsVise jaw positioning To rapidly change the vise jaw gapCutting Angle To change the angleBlade Selection Blade SpeedTo change blade speeds Feed Rate To set the feed rateTo adjust the rear blade guide Blade GuidesCoolant System To use the coolant systemSpray gun G0592 Metal Cutting Bandsaw Cutting Fluid Operation Tips Tips for horizontal cuttingAccessories H5405-LenoxLube TubeG7897-Machining Fluid H1302-Standard Earmuffs H1302 H4979 H4977H1300 H1298 G7984 H2347 H0736 Maintenance CleaningSchedule LubricationVise leadscrew lubrication area Service TroubleshootingBandsaw Operations Blade Change To change the blade on the bandsawTo adjust the blade tracking on the bandsaw Blade Tension TrackingTo tension the blade on the bandsaw To adjust the blade guide bearings Blade Guide BearingsLimit switch Electrical ComponentsTransformer Contactor Relay Terminal Block Model G0592 220V Wiring Diagram Parts Breakdown Base Parts List DescriptionSwivel Base Swivel Base Parts List Vise Parts Breakdown Vise Parts List Bow Parts Breakdown Bow Parts List Blade Tension Blade Tension & Motor Parts List PB87MBladeGuides Blade Guides Parts List Electrical Parts Electrical Parts List Warranty and Returns Page Page

G0592 specifications

The Grizzly G0592 is a high-performance milling machine designed to meet the demands of both professional and hobbyist woodworkers. Known for its robust construction and precise engineering, this machine combines versatility with durability, making it an essential tool for any woodworking shop.

One of the standout features of the G0592 is its powerful motor, which offers a significant amount of torque, enabling it to handle a variety of materials with ease. The machine is equipped with a 3 HP motor that operates on 220V single-phase power, providing consistent performance for heavy-duty milling tasks. This high power helps to minimize stalling or bogging down during operation, ensuring smooth and efficient cutting.

The G0592 also boasts a generous working table made from precision-ground cast iron, measuring 9” x 49”. This extensive surface area allows for the handling of larger workpieces and offers ample space for stock support. The table is fitted with T-slots, allowing for easy attachment of jigs, fixtures, and clamping tools, enhancing the versatility of the machine.

Another notable characteristic is its adjustable dovetail ways, which provide enhanced stability and precision during operation. This design helps in maintaining alignment and reduces wear on the machine over time. Additionally, the G0592 features a variable speed drive that allows users to adjust the spindle speed from 60 to 4,000 RPM, accommodating various cutting applications ranging from heavy milling to delicate engraving.

The head of the G0592 is also a significant aspect of its design. It can be swiveled up to 90 degrees, facilitating angular cuts and increasing the range of milling operations possible. Moreover, the machine includes a digital readout (DRO) for both the table and spindle positions, providing real-time feedback and enhanced accuracy during operations.

Safety features, such as an emergency stop button and a protective enclosure around the spindle, are integrated into the G0592 to ensure a safe working environment. Overall, the Grizzly G0592 is engineered for those who value precision and performance in their milling tasks, making it a reliable choice in both professional and amateur settings. Its robust build, ample features, and user-friendly design distinguish it as a leading option in the milling machine market.
Top Page Image Contents