Grizzly G0717 owner manual Safety Instructions for Machinery

Page 8

SECTION 1: SAFETY

For Your Own Safety, Read Instruction Manual Before Operating this Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of impor- tance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

 

 

Indicates an imminently hazardous situation which, if not avoided,

 

 

 

 

WILL result in death or serious injury.

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

COULd result in death or serious injury.

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided,

 

 

 

 

MAY result in minor or moderate injury. It may also be used to alert

 

 

 

 

against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about

proper operation of the machine.

Safety Instructions for Machinery

OWNER’S MANUAL. Read and understand this owner’s manual BEFORE using machine. Untrained users can be seriously hurt.

EYE PROTECTION. Always wear ANSI-approved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are not approved safety glasses.

HAzARdOUS dUST. Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, and always wear a NIOSH-approved respirator to reduce your risk.

WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips which could cause a loss of work- piece control.

HEARING PROTECTION. Always wear hear- ing protection when operating or observiing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss.

MENTAL ALERTNESS. Be mentally alert when running machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted.

-6-

Model G0717 (Mfg. Since 9/10)

Image 8
Contents Model G0717 Page Table of Contents Machine Description IntroductionManual Accuracy Contact Info Identification Machine Data Sheet Other Safety Safety Instructions for MachineryUnattended OPERATION. Never­ leave­ Safety Instructions for Metal Cutting Bandsaws Power Supply AvailabilityFull-Load Current Rating Circuit InformationGrounding Requirements Extension CordsMinimum Gauge Size 12 AWG 50 ftSetup Needed for SetupUnpacking Description QtyInventory Item Figure QtyBasic steps for removing rust preventative CleanupBefore cleaning, gather the following Site Considerations Using Machine Mounts Lifting & PlacingMounting Bolting to Concrete FloorsAssembly To assemble your machineMounting belt cover Model G0717 Mfg. Since 9/10 Disconnecting Power Power ConnectionConnecting Power Controls Blade on Button Starts the blade Test Run Operations Operation OverviewBlade Selection Blade TerminologyBlade Length ModelTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Change To change the blade on the bandsawBlade Tension To tension the blade on the bandsawMost common causes of avoidable blade breakage are Blade TrackingBlade Breakage Blade Care Break-In DownfeedBlade Care Blade Break-InDownfeed Pressure Blade Speed To change blade speedsChip Inspection Chart Blade Speed ChartTo rapidly change the vise jaw gap To adjust the rear blade guide armVise Blade Guide Arms Cutting Fluid HazardCutting Fluid System To use the cutting fluid systemBlade Brush Typical blade brushOperation Tips Accessories H9231-Safe Tap Stick, 13 ozBasic Eye Protection H4978 T20446 H4979Maintenance CleaningSchedule LubricationTo change the gear oil Gear boxMotor & Electrical ServiceTroubleshooting Bandsaw Operations Refer to Feed Rate on Page 29, or Blade SpeedBelt To replace the V-beltWiring Wiring Safety InstructionsWiring Overview SeeWiring Diagram 110 VACElectrical Box 27-1 53-2 66-1 28-1 53-1 72-1 70-1 29-1 52-1 Base Parts List DescriptionPW06M Flat Washer 12MM PB35M Bow ModelSaw Bow Parts List Motor Mount PlatePCAP07M CAP Screw M6-1 X Labels Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns Order Hours a DAY