Grizzly G0717 owner manual Site Considerations

Page 16

Site Considerations

Weight Load

Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is placed will bear the weight of the machine, additional equipment that may be installed on the machine, and the heaviest work- piece that will be used. Additionally, consider the weight of the operator and any dynamic loading that may occur when operating the machine.

Space Allocation

Consider the largest size of workpiece that will be processed through this machine and provide enough space around the machine for adequate operator material handling or the installation of auxiliary equipment. With permanent installations, leave enough space around the machine to open or remove doors/covers as required by the main- tenance and service described in this manual.

See below for required space allocation.

Children or untrained people may be seriously injured by this machine. Only install in an access restricted location.

Physical Environment

The physical environment where your machine is operated is important for safe operation and the longevity of its components. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous chemi- cals, airborne abrasives, or extreme conditions. Extreme conditions for this type of machinery are generally those where the ambient temperature range exceeds 41°–104°F; the relative humidity range exceeds 20–95% (non-condensing); or the environment is subject to vibration, shocks, or bumps.

Electrical Installation

Place this machine near an existing power source. Make sure all power cords are protected from traffic, material handling, moisture, chemicals, or other hazards. Make sure to leave access to a means of disconnecting the power source or engaging a lockout/tagout device.

Lighting

Lighting around the machine must be adequate enough that operations can be performed safely. Shadows, glare, or strobe effects that may distract or impede the operator must be eliminated.

 

Wall

 

 

30" Minimum

 

15"

 

 

 

29"

Wall

 

 

18.5"

 

 

 

6"

 

64"

30" Minimum

 

 

 

Figure 7. Minimum working clearances.

-14-

Model G0717 (Mfg. Since 9/10)

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Model G0717 Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description Identification Machine Data Sheet Other Safety Safety Instructions for MachineryUnattended OPERATION. Never­ leave­ Safety Instructions for Metal Cutting Bandsaws Power Supply AvailabilityFull-Load Current Rating Circuit InformationGrounding Requirements Extension CordsMinimum Gauge Size 12 AWG 50 ftSetup Needed for SetupUnpacking Description QtyInventory Item Figure QtyBefore cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Using Machine Mounts Lifting & PlacingMounting Bolting to Concrete FloorsAssembly To assemble your machineMounting belt cover Model G0717 Mfg. Since 9/10 Connecting Power Power ConnectionDisconnecting Power Controls Blade on Button Starts the blade Test Run Operations Operation OverviewBlade Selection Blade TerminologyBlade Length ModelTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Change To change the blade on the bandsawBlade Tension To tension the blade on the bandsawBlade Breakage Blade TrackingMost common causes of avoidable blade breakage are Blade Care Break-In DownfeedBlade Care Blade Break-InDownfeed Pressure Blade Speed To change blade speedsChip Inspection Chart Blade Speed ChartVise Blade Guide Arms To adjust the rear blade guide armTo rapidly change the vise jaw gap Cutting Fluid HazardCutting Fluid System To use the cutting fluid systemBlade Brush Typical blade brushOperation Tips Accessories H9231-Safe Tap Stick, 13 ozBasic Eye Protection H4978 T20446 H4979Maintenance CleaningSchedule LubricationTo change the gear oil Gear boxTroubleshooting ServiceMotor & Electrical Bandsaw Operations Refer to Feed Rate on Page 29, or Blade SpeedBelt To replace the V-beltWiring Wiring Safety InstructionsWiring Overview SeeWiring Diagram 110 VACElectrical Box 27-1 53-2 66-1 28-1 53-1 72-1 70-1 29-1 52-1 Base Parts List DescriptionPW06M Flat Washer 12MM PB35M Bow ModelSaw Bow Parts List Motor Mount PlatePCAP07M CAP Screw M6-1 X Labels Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WAWarranty & Returns Order Hours a DAY
Top Page Image Contents