Grizzly G0668 owner manual Labels

Page 56

Labels

��

��

��

��

��

��

��

��

REF	PART #	DESCRIPTION

401	P0668401	MODEL # LABEL
402	P0668402	BLADE SPECIFICATION LABEL
403	P0668403	POWER DISCONNECT LABEL VERT S
404	P0668404	EYE/LUNG HAZARD LABEL VERT L
405	PLABEL-12	READ MANUAL LABEL VERT L
406	G8588	GRIZZLY NAMEPLATE 9-1/2" X 4-1/2"

REF	PART #	DESCRIPTION

407	P0668407	MACHINE ID LABEL
408	P0668408	BLADE HAZARD LABEL VERT L
409	P0668409	DOOR INJURY HAZARD LABEL VERT S
410	PPAINT-11	GRIZZLY PUTTY TOUCH UP PAINT
412	P0668412	STABLE WORKPIECE LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-54-	G0668 20" Vertical Metal-Cutting Bandsaw

Image 56

Contents Model G0668 Vertical METAL-CUTTING Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0668 20 Vertical Metal-Cutting Bandsaw Identification Control Panel Identification Safety Instructions for Machinery G0668 20 Vertical Metal-Cutting Bandsaw Safety Instructions for Metal Cutting Bandsaws 220V 3-Phase Operation Circuit RequirementsSetup Setup SafetyItems Needed for Setup UnpackingClean Up Placement LocationG2544-Solvent Cleaner & Degreaser Site ConsiderationsBolting to Concrete Floors Mounting to Shop FloorMoving & Placing Test Run To test run the bandsawRecommended Adjustments Factory adjustments that should be verifiedOperation Safety Cutting Overview OperationsCutting Tips Workpiece InspectionBasic Controls Electrical controlsBlade Selection Blade TerminologyBlade Length Blade WidthTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Breakage Blade Care Break-InBlade Care Blade Break-InChip Inspection Chart Disconnect Bandsaw from Power Blade ChangesBlade Tensioning Guide PostTo correctly tension the blade To properly position the guide postAdjusting Blade Guides & Supports Upper blade guides and bracketAdjusting Table Tilt To adjust the table tiltUsing the grinder to square up Blade end Blade WeldingBlade Width Pressure Setting Blade clamping pressure chartCorrect blade weld bend for strength Flexibility Accessories T20448T20452 T20501 T20456 H0736Maintenance CleaningSchedule DailyTo redress the rubber tires Redressing Rubber TiresLubrication Motor & Electrical ServiceTroubleshooting Cutting Operations Pages 36Lower Wheel Pulley Alignment Tensioning V-BeltsTools Needed Qty To check/tension/replace the V-beltsAdjusting Wheel Brush To adjust the wheel brushReplacing V-Belts To replace the motor V-beltsTo check if your wheels are parallel and copla- nar Wheel AlignmentMaterials Needed Qty To adjust the upper wheel To adjust the lower wheelTo adjust the table square to the blade Aligning Table to BladeBlade Guides Electrical & Control Wiring Diagram See onInverter Wiring Diagram DigitalControl panel wiring see wiring Electrical ComponentsMotor Wiring Diagram SeeWelding Station Wiring Diagram Welding station wiring To Electrical PanelParts CabinetTable & Lower Guide Motor & Lower Wheel Station Welding Station Parts List PSB02M Upper Wheel Labels Page Page Warranty and Returns