Grizzly G0668 owner manual Adjusting Table Tilt, To adjust the table tilt

Page 29

5.Slide the blade support (see Figure 23) up to, but not touching, the back of the blade, then re-tighten the blade support cap screw.

Blade Guide

Cap Screws

Air Nozzle

Blade Support

Figure 23. Blade guide assembly (upper assembly shown without blade for clarity).

6.Rotate the upper wheel by hand so that the blade weld is between the blade guides.

7.Use a 4mm hex wrench to loosen the blade guide cap screws (see Figure 23).

8.Fold a crisp dollar bill in half and place it over the blade (between the blade guides and the blade), as shown in Figure 24.

Figure 24. Using a dollar bill to set blade guide

spacing.

G0668 20" Vertical Metal-Cutting Bandsaw

9.Lightly pinch the dollar bill against the blade with the blade guides, re-position the air nozzle if necessary, then re-tighten the blade guide cap screws.

Note: The goal is to position the blade guides as close as possible to the blade without touching it during operation.

Adjusting Table Tilt

To perform beveled cuts, the bandsaw table tilts 15° to the left and 45° to the right.

To adjust the table tilt:

1.DISCONNECT BANDSAW FROM POWER!

2.Use a 23mm wrench to loosen the hex nut underneath the rear of the table (see Figure 25).

Table Tilt Scale

Hex Nut

Figure 25. Table tilt scale and hex nut.

3.Using the table tilt scale, adjust the angle of the table for your operation, then re-tighten the hex nut.

-27-

Image 29

Contents Model G0668 Vertical METAL-CUTTING Bandsaw Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0668 20 Vertical Metal-Cutting Bandsaw Identification Control Panel Identification Safety Instructions for Machinery G0668 20 Vertical Metal-Cutting Bandsaw Safety Instructions for Metal Cutting Bandsaws Circuit Requirements 220V 3-Phase OperationSetup Safety SetupItems Needed for Setup UnpackingPlacement Location Clean UpG2544-Solvent Cleaner & Degreaser Site ConsiderationsBolting to Concrete Floors Mounting to Shop FloorMoving & Placing To test run the bandsaw Test RunFactory adjustments that should be verified Recommended AdjustmentsOperations Operation Safety Cutting OverviewWorkpiece Inspection Cutting TipsElectrical controls Basic ControlsBlade Terminology Blade SelectionBlade Length Blade WidthTooth Type Tooth SetTo select the correct blade pitch Blade Pitch TPIBlade Care Break-In Blade BreakageBlade Care Blade Break-InChip Inspection Chart Blade Changes Disconnect Bandsaw from PowerGuide Post Blade TensioningTo correctly tension the blade To properly position the guide postUpper blade guides and bracket Adjusting Blade Guides & SupportsTo adjust the table tilt Adjusting Table TiltBlade Welding Using the grinder to square up Blade endBlade clamping pressure chart Blade Width Pressure SettingCorrect blade weld bend for strength Flexibility T20448T20452 T20501 T20456 H0736 AccessoriesCleaning MaintenanceSchedule DailyTo redress the rubber tires Redressing Rubber TiresLubrication Motor & Electrical ServiceTroubleshooting Pages 36 Cutting OperationsTensioning V-Belts Lower Wheel Pulley AlignmentTools Needed Qty To check/tension/replace the V-beltsTo adjust the wheel brush Adjusting Wheel BrushReplacing V-Belts To replace the motor V-beltsTo check if your wheels are parallel and copla- nar Wheel AlignmentMaterials Needed Qty To adjust the lower wheel To adjust the upper wheelAligning Table to Blade To adjust the table square to the bladeBlade Guides See on Electrical & Control Wiring DiagramDigital Inverter Wiring DiagramElectrical Components Control panel wiring see wiringSee Motor Wiring DiagramWelding station wiring To Electrical Panel Welding Station Wiring DiagramCabinet PartsTable & Lower Guide Motor & Lower Wheel Station Welding Station Parts List PSB02M Upper Wheel Labels Page Page Warranty and Returns