Grizzly G1023ZX3 instruction manual Service Adjustments, 45˚ & 90˚ Stops

Page 44

SECTION 8: SERVICE ADJUSTMENTS

!

Disconnect power to the

machine when perform-

ing

any

maintenance,

 

assembly

or

adjust-

 

ments. Failure to do this

 

may

result in

serious

 

personal injury.

 

Keep loose clothing rolled up and out of the way of machinery and keep hair pulled back.

Wear safety glasses during the entire adjust- ment process. Failure to comply may result in serious personal injury.

45˚ & 90˚ Stops

1.Set your blade angle at zero as shown on the angle indicator on the front of the saw and raise the blade several inches above the table.

2.Place a machinistÕs square flat on the table and slide it alongside the blade. The square should contact the blade evenly from bottom to top. Make sure that a blade tooth does not obstruct the movement of the square.

3.Adjust the handwheel until the square is flush with the blade. Loosen the tilt indicator arrow, set to zero, and retighten. Loosen and adjust the stop bolt on the left side of the front trunnion to allow a 90¡ stop point. See Figure 40 for details.

4.Turn the blade angle handwheel until the angle indicator points at the desired angle.

5.Tighten the handwheel locking knob.

6.Repeat Steps 1-6for setting the blade to 45¡ and adjust the 45¡ stop bolt on the right side of the front trunnion. Use the 45¡ side of a combo square or a bevel gauge set at 45¡.

45û Stop Bolt

90û Stop Bolt

Figure 40. Geared trunnion.

-42-

G1023Z Series Heavy-Duty 10'' Table Saw

Page 43 Page 45
Image 44
Page 43 Page 45
Contents HEAVY-DUTY Table SAW Model G1023Z, ZX & ZX3Page Table of Contents Safety Safety Instructions For Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions For Table Saws Avoiding Kickback Safety Accessories Following can help minimize kickbacksFeatherboards Zero Clearance Table InsertsPush Paddles Introduction CommentaryCircuit Requirements G1023ZG1023ZX G1023ZX3 Grounding Extension Cord Machine Features Terms & DefinitionsMain Features SET UP Unpacking Piece InventoryG1023Z Series component layout Hardware Recognition Chart Clean Up Site ConsiderationsFloor Load Working ClearanceBeginning Assembly Extension Wings Switch To mount the switchDisconnect the machine from the power source Fence & RailsTo mount the dust hood and cleanout door Dust Hood Motor CoverMotor Brace Guard BracketHandwheel Table InsertSaw Blade Blade Guard/SplitterFront Support Blade Adjustment Bolt To adjust the miter gauge Miter GaugeStarting the machine Recommended adjustment checklistStart Up Recommended Operations Blade SelectionPage Crosscutting Cross-cut operation G1023Z Series Heavy-Duty 10 Table SawRipping Ripping operationDado Cutting Single-blade dado cutIf the cut is satisfactory, repeat with your fin- ish stock Rabbet Cutting Sacrificial fence G1023Z Series Heavy-Duty 10 Table SawCutting rabbets with the dado blade Rabbet cutting G1023Z Series Heavy-Duty 10 Table SawCutting rabbets with the standard blade Rabbet cutting G1023Z Series Heavy-Duty 10 Table Saw Maintenance GeneralLubricate the areas indicated below every 12 months LubricationTableBelt Belt deflection Date Approximate Hours Of Use Maintenance Performed Service Adjustments 45˚ & 90˚ StopsBlade Parallelism Page Blade Alignment Trunnion mounting boltsPage G1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Page Closure Machine Data Sheet G1023Z / G1023ZX / G1023ZX3G1023Z Series Heavy-Duty 10 Table Saw Cabinet Complete Miter Gauge Troubleshooting Guide Symptom Possible Cause Corrective ActionG1023Z Series Heavy-Duty 10 Table Saw G1023Z Series Heavy-Duty 10 Table Saw Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog

G1023ZX, G1023Z, G1023ZX3 specifications

The Grizzly G1023ZX3, G1023Z, and G1023ZX are standout options in the world of table saws, known for their precision, durability, and powerful performance. Each model offers unique features and specifications that cater to the needs of both amateur woodworkers and seasoned professionals alike.

The G1023ZX3 is particularly notable for its innovative design and advanced technology. It features a 3 HP motor that ensures consistent and high-quality cuts through even the densest hardwoods. This model is equipped with a 30-inch extension table, providing ample workspace for large projects. Its heavy-duty cast iron construction not only enhances stability but also minimizes vibrations, promoting accuracy during operation. The G1023ZX3 also includes a precision-ground table and a clear polycarbonate blade guard, which offers visibility and safety while cutting.

The G1023Z is a slightly more compact and affordable version, though it does not compromise on performance. It still features a robust 3 HP motor, ensuring reliable power for various woodworking tasks. This model is designed with a 27-inch table and integrates a quick-release blade guard, making it easy to install and remove when necessary. The G1023Z's easy-to-use handwheel for raising and lowering the blade simplifies adjustments, making this model particularly user-friendly.

The G1023ZX is a versatile model that bridges the gap between the G1023ZX3 and G1023Z. It offers an impressive 3 HP motor and boasts a 30-inch table, just like the ZX3. The G1023ZX is equipped with a built-in mobile base that allows for easy maneuverability, which is a great advantage in workshops with limited space. This model also features a high-quality T-square style fence system that ensures precise measurements and straight cuts, catering to the needs of both novice and expert woodworkers.

All models incorporate high-quality safety features such as riving knives and anti-kickback pawls, ensuring user protection during operation. Furthermore, the durable construction and thoughtful design of these table saws allow for prolonged use, making them a worthwhile investment for anyone serious about woodworking. In conclusion, the Grizzly G1023 series, including the G1023ZX3, G1023Z, and G1023ZX, stands out for their exceptional engineering, versatility, and commitment to safety, making them ideal for achieving accurate and efficient results in woodworking projects.
Top Page Image Contents