Grizzly G5959Z instruction manual Blade Alignment

Page 26

Blade Alignment

If the blade contacts the table insert when raised or tilted, the blade must be aligned. The easiest way is to move the table. If moving the table does not work, adjust the trunnion assembly. If that does not work, move the arbor bracket.

To adjust the blade by moving the table:

1.Disconnect the table saw from the power source.

2.Loosen the four table mounting bolts and adjust the table until the blade does not con- tact the insert. Tighten all the mounting bolts.

3.Make sure the blade does not contact the table insert when raised or tilted. Recheck splitter alignment and parallelism of the blade to the miter slot. Adjust as necessary.

To adjust the blade by moving the trunnion:

1.Disconnect the table saw from the power source.

2.Get assistance to remove the table and wings and set them to one side.

3.Loosen the four trunnion mounting bolts as shown in Figure 30, and adjust the trunnion.

Figure 30. Trunnion mounting bolts.

4.Reattach the table and make sure the blade does not contact the table insert when raised or tilted.

-24-

5.Tighten all the table mounting bolts. Recheck splitter alignment and parallelism of the blade to the miter slot. Adjust as necessary.

To adjust the blade by moving the arbor bracket:

1.Disconnect the table saw from the power source.

2.Get assistance to remove the table and wings and set them to one side.

Blade Adjustment Cap Screw

Arbor Bracket

Figure 31. Adjusting arbor bracket.

2.Loosen the blade adjustment cap screw shown in Figure 31.

3.To adjust the arbor bracket, loosen the cap screw and the setscrew. Slowly slide the arbor bracket towards the end of the shaft.

4.Moving the arbor bracket moves the V-belts and pulleys out of alignment, so adjustment of the motor pulley is required. Loosen the setscrew and slowly slide the pulley towards the end of the motor shaft. Once the V-belts are back into alignment, tighten the setscrew securely.

5.Reattach the table and tighten all the mount- ing bolts.

6.Make sure the blade does not contact the table insert when raised or tilted. Recheck splitter alignment and parallelism of the blade to the miter slot. Adjust as necessary.

G5959Z 12" Left-Tilting Table Saw

Image 26
Contents HEAVY-DUTY LEFT-TILTING Table SAW Page Table Of Contents Safety Safety Instructions For Power ToolsAMP Rating Additional Safety Instructions For Table Saws Push Sticks Zero Clearance Table InsertsPush Paddles FeatherboardCommon Definitions, Terms and Phrases 220V Single-Phase Circuit RequirementsWiring Diagram Grounding Extension CordsIntroduction CommentaryUnpacking Piece InventoryClean Up Site Considerations Extension Wings AssemblyBeginning Assembly Wings represent aGuard Support Shaft Attaching guard support shaftFence Rails Motor BracketInstalling Saw Blade Table InsertBlade Guard/Splitter Improper splitter/blade alignmentAdjusted Rear Blade Tilt AdjustmentsBlade Height Miter Slot to Blade ¡ blade parallelism Blade tilted to 45û #1#3 Front #2#4 Miter Gauge Rip Fence SquareClamping Pressure Blade Alignment Test Run OperationsPre-Run Check Blade Selection Plywood blade G5959Z 12 Left-Tilting Table SawTo make a crosscut using the miter gauge CrosscuttingRipping Dado OperationsDisconnect the table saw from the power source Rabbet Operations Rabbet cutting G5959Z 12 Left-Tilting Table SawG5959Z 12 Left-Tilting Table Saw Belt MaintenanceGeneral To replace the V-belts To adjust V-belt tensionLubrication Closure Aftermarket AccessoriesReplacement Blades Model Super Heavy-Duty Shop Fox Mobile Base Model G7315Machine Data Sheet HP Magnetic Switch -NHD Type 1L1 3L2 5L3 no 2T1 4T2 6T3 no401 403 411 Page G5959Z 12 Left-Tilting Table Saw 7472 7778 41A 45A G5959Z 53 45A Left-Tilting Table Saw Page Description Line Cord Short Troubleshooting Guide CUT Here to Push 1⁄4 Wood CUT Here to Push 1⁄2 Wood Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WACall Today For a Free Full Color Catalog