Grizzly G0460, G0461 owner manual Operations, Operation Safety, Operation Tips

Page 34

SECTION 4: OPERATIONS

Operation Safety

Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine.

Loose hair and cloth-

ing could get caught in

machinery and cause seri-

ous personal injury. Keep

loose clothing and long

hair away from moving machinery.

NOTICE

If you have never used this type of machine or equipment before, WE STRONGLY REC- OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training.

-32-

Operation Tips

Your safety is important. The tips below are intended to supplement SECTION 1: SAFETY. But remember, no safety list can be comprehen- sive of every situation. The operator is ultimately responsible for their own safety, as well as the safety of bystanders. Every cutting operation is uniquely different and may require safety equip- ment or safety procedures not mentioned in this manual.

Please follow these tips EVERY time you use your saw:

•Stand to the left of the blade line-of-cut when operating the saw to reduce your risk of injury if a kickback occurs.

•Turn OFF the saw and allow the blade to come to a complete stop before removing the cut-off piece.

•Make sure that the riving knife is always aligned with the main blade before cutting.

•Always position the blade guard to the correct height above the workpiece.

•Carefully plan each cutting operation to avoid injuries.

•When you release the sliding table lock, make sure that the knob is positioned so that it will not lock the table during a cut.

G0460/G0461 12" Sliding Table Saw

Page 33 Page 35
Image 34
Page 33 Page 35
Contents
Sliding Table SAW Page Table of Contents Foreword IntroductionContact Info Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Protecting Yourself From Kickback Preventing KickbackTips to reduce the likelihood of kickback Glossary of Terms Circuit Requirements Rewiring to GroundingMagnetic switch Items Needed for Setup SetupSetup Safety Unpacking Description QtyClean Up Inventory Inventory QtyHardware and Tools Lock Washers 8mm Small Wing/TableHardware Recognition Chart Moving & Placing Base Unit PlacementSite Considerations Floor LoadMounting to Shop Floor Bolting to Concrete FloorsExtension Tables To install the extension tablesComponents and Hardware Needed Qty To install the blade Main BladeTo install the rip fence Rip Fence and ScalePage To install the riving knife Riving KnifeSet screws for adjusting riving knife To install the scoring blade Scoring Blade Crosscut Table To install the crosscut table Aligning Blades To align the blades and riving knifeTo install the crosscut fence Crosscut FenceFence Scale Alignment To align the rip fence scale with the bladeTest Run Operation Tips Operation SafetyOperations Please follow these tips Every time you use your sawChanging Blades To change the bladesRip Cutting Rip cutting with the sliding tableRip cutting with the rip fence Crosscutting Crosscutting full size panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting smaller panels Miter Cutting To perform a miter cutG3445-Precision Saw Tool AccessoriesH3308-SHOP FOX Push Stick H3771-Blade LocH1300 H1298 G7984 H2347 H0736 H6460-12 Tooth Scoring Blade SetSchedule MaintenanceCleaning Unpainted Cast IronLubrication See FigureSymptom Possible Cause Possible Solution ServiceTroubleshooting Motor & ElectricalCutting Operations To change the main blade arbor V-belt Replacing BeltsTo change the scoring blade arbor flat belt Blade Tilt To calibrate the blade tiltSquaring Crosscut Fence to Blade To square the crosscut fence with the bladeTo adjust the sliding table parallel with the main blade Sliding Table ParallelismG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Parts Main BodyMain Body Parts List DescriptionPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly Motor Assembly PK42MArbor Assembly Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WA
Top Page Image Contents