Grizzly G0460, G0461 Fence Scale Alignment, To align the rip fence scale with the blade

Page 32
Dust Collection
Components and Hardware Needed: Qty Blade Guard Dust Hood .....................................1
Flat Washer 8mm ...............................................1
Adjustable Handle M8-1.25 x 28 ........................1
5" Dust Hose (not included) ...............................1
5" Hose Clamp (not included) ............................2
2½" Dust Hose (not included) ............................1
2½" Hose Clamp (not included) .........................2
Dust Collection System (not included) ...............1
To connect the dust ports to a dust collector:
1. Run a 5" hose from the dust collector to the dust port located under the saw table (Figure 47) and secure it with hose clamps.
5" Dust
Port
2½" Dust
Port
Figure 47. Dust port locations.
2. Install the blade guard/dust hood on the riv- ing knife with the adjustable handle and flat washer as shown in Figure 47.
3. Run a 2½" hose from the dust collector to the blade guard port (Figure 47) and secure it with hose clamps.
G0460/G0461 12" Sliding Table Saw

3.Thread the knobs onto the T-bolts to secure the crosscut fence.

4.Unlock the fence extension and slide the flip stops into the fence as shown in Figure 46.

Figure 46. Stop block installation.

Fence Scale

Alignment

Before operation, align the 0" mark on the rip fence scale with the right side of the blade to ensure accurate measurements.

To align the rip fence scale with the blade:

1.Move the blade tilt to 0° (blade 90° to table), and raise the main blade all the way up.

2.Remove the stop screw from the round rail and move the rip fence against the blade.

3.Loosen the cap screws securing the scale.

4.Slide the fence scale to line up the first mark on the scale with the left edge of the rip fence and tighten the cap screws.

5.Slide the fence away from the blade and replace the stop screw.

-30-

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Sliding Table SAW Page Table of Contents Contact Info IntroductionForeword Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Tips to reduce the likelihood of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Circuit Requirements Rewiring to GroundingMagnetic switch Setup Setup Safety UnpackingItems Needed for Setup Description QtyClean Up Inventory Inventory QtyHardware and Tools Lock Washers 8mm Small Wing/TableHardware Recognition Chart Placement Site ConsiderationsMoving & Placing Base Unit Floor LoadMounting to Shop Floor Bolting to Concrete FloorsComponents and Hardware Needed Qty To install the extension tablesExtension Tables To install the blade Main BladeTo install the rip fence Rip Fence and ScalePage To install the riving knife Riving KnifeSet screws for adjusting riving knife To install the scoring blade Scoring BladeTo install the crosscut table Aligning BladesCrosscut Table To align the blades and riving knifeTo install the crosscut fence Crosscut FenceFence Scale Alignment To align the rip fence scale with the bladeTest Run Operation Safety OperationsOperation Tips Please follow these tips Every time you use your sawChanging Blades To change the bladesRip Cutting Rip cutting with the sliding tableRip cutting with the rip fence Crosscutting Crosscutting smaller panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting full size panels Miter Cutting To perform a miter cutAccessories H3308-SHOP FOX Push StickG3445-Precision Saw Tool H3771-Blade LocH1300 H1298 G7984 H2347 H0736 H6460-12 Tooth Scoring Blade SetMaintenance CleaningSchedule Unpainted Cast IronLubrication See FigureService TroubleshootingSymptom Possible Cause Possible Solution Motor & ElectricalCutting Operations To change the scoring blade arbor flat belt Replacing BeltsTo change the main blade arbor V-belt Blade Tilt To calibrate the blade tiltSquaring Crosscut Fence to Blade To square the crosscut fence with the bladeTo adjust the sliding table parallel with the main blade Sliding Table ParallelismG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Parts Main BodyMain Body Parts List DescriptionPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly Motor Assembly PK42MArbor Assembly Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WA

G0461, G0460 specifications

The Grizzly G0460 and G0461 are renowned woodworking machines in the arena of jointers and planers, designed specifically to meet the needs of both amateur woodworkers and professional craftsmen. These machines are celebrated for their engineering excellence, offering robust features and advanced technologies that facilitate precision in woodworking projects.

The Grizzly G0460 is a 6-inch jointer that is engineered for efficiency and accuracy, boasting a powerful 1 HP motor. This model is particularly suitable for achieving flat surfaces on wooden boards, with its precision-machined cast iron table providing an exceptionally smooth finish. The G0460's adjustable infeed and outfeed tables ensure optimal alignment, enabling users to handle both narrow and wide stock with ease. The jointer also features a convenient fence system that can be locked at a 90-degree angle or angled up to 45 degrees for bevel cuts, making it a versatile addition to any workshop.

In contrast, the Grizzly G0461 is an 8-inch version of its counterpart, offering increased capacity and capabilities for larger projects. With a similar 1 HP motor, the G0461 allows users to joint wider boards, making it ideal for serious woodworkers who demand higher performance levels. The machine's heavy-duty construction features a cast iron base and table, which not only add stability but also minimize vibrations during operation for enhanced accuracy.

Both models utilize helical cutter heads, which significantly improve the cutting experience. This technology employs multiple small, indexed carbide inserts that provide a smoother cut, reduce noise, and prolong the life of the cutter. The ease of changing the inserts enhances usability, making maintenance less cumbersome for users.

Moreover, safety features such as the blade guard are incorporated into both models, ensuring operator protection. The adjustable depth of cut allows for customized finishes, giving users control over the smoothing process.

In summary, the Grizzly G0460 and G0461 are exceptional tools that combine power, precision, and innovative design. Their capabilities cater to a wide range of woodworking applications, making them reliable choices for anyone serious about crafting fine wood items. Users will appreciate the blend of performance, ease of use, and durability that these machines bring to their woodworking endeavors. Whether tackling small projects or large production runs, the G0460 and G0461 stand as testament to Grizzly's commitment to quality in the woodworking machinery market.
Top Page Image Contents