Grizzly G0460, G0461 owner manual H1300 H1298 G7984 H2347 H0736, H6460-12 Tooth Scoring Blade Set

Page 42

G7984—Face Shield

H1298—Dust Sealed Safety Glasses

H1300—UV Blocking, Clear Safety Glasses

H2347—Uvex®Spitfire Safety Glasses

H0736—Shop Fox® Safety Glasses

Safety Glasses are essential to every shop. If you already have a pair, buy extras for visitors or employees. You can't be too careful when it comes to shop safety!

H1300

H1298

G7984

H2347

H0736

Figure 70. Our most popular safety glasses.

G5562—SLIPIT®1 Qt. Gel G5563—SLIPIT®12 oz Spray G2871—Boeshield®T-9 12 oz Spray G2870—Boeshield®T-9 4 oz Spray H3788—G96®Gun Treatment 12 oz Spray H3789—G96®Gun Treatment 4.5 oz Spray

Figure 71. Recommended products for protect- ing unpainted cast iron/steel part on machinery.

-40-

Carbide-Tipped Saw Blades (ATB) G4808—12" Ripping, 40T G4809—12" General Purpose, 60T G4810—12" Fine Finishing/Cabinet Work, 80T These ATB blades are manufactured to close tol- erances and are fully balanced before leaving the factory. All the carbide-tipped teeth are precisely ground to give a smooth cut every time. The pat- tern of the teeth is alternate top bevel and the saw kerf is approx. 1⁄8". These blades have proven themselves in thousands of cabinet shops around the country. Manufactured for heavy-duty use.

Figure 72. Carbide-tipped saw blades.

H6460—12 Tooth Scoring Blade Set

The scoring blade set consists of an inner and outer blade and four internal shims. Two shims are 0.008" thick and two are 0.004". The shims are provided so the scoring blade set can match the kerf thickness of the main blade.

Figure 73. H6460 Scoring Blade Set.

G0460/G0461 12" Sliding Table Saw

Image 42

Contents

Sliding Table SAW Page Table of Contents Introduction ForewordContact Info Machine Data Sheet G0460/G0461 12 Sliding Table Saw Identification Page Safety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Sliding Table Saws Preventing Kickback Protecting Yourself From KickbackTips to reduce the likelihood of kickback Glossary of Terms Circuit Requirements Rewiring to GroundingMagnetic switch Items Needed for Setup SetupSetup Safety Unpacking Description QtyClean Up Inventory Inventory QtyHardware and Tools Lock Washers 8mm Small Wing/TableHardware Recognition Chart Moving & Placing Base Unit PlacementSite Considerations Floor LoadMounting to Shop Floor Bolting to Concrete FloorsTo install the extension tables Extension TablesComponents and Hardware Needed Qty To install the blade Main BladeTo install the rip fence Rip Fence and ScalePage To install the riving knife Riving KnifeSet screws for adjusting riving knife To install the scoring blade Scoring BladeCrosscut Table To install the crosscut tableAligning Blades To align the blades and riving knifeTo install the crosscut fence Crosscut FenceFence Scale Alignment To align the rip fence scale with the bladeTest Run Operation Tips Operation SafetyOperations Please follow these tips Every time you use your sawChanging Blades To change the bladesRip Cutting Rip cutting with the sliding tableRip cutting with the rip fence Crosscutting Crosscutting using the rip fence as a cut-off gauge Crosscutting full size panelsCrosscutting smaller panels Miter Cutting To perform a miter cutG3445-Precision Saw Tool AccessoriesH3308-SHOP FOX Push Stick H3771-Blade LocH1300 H1298 G7984 H2347 H0736 H6460-12 Tooth Scoring Blade SetSchedule MaintenanceCleaning Unpainted Cast IronLubrication See FigureSymptom Possible Cause Possible Solution ServiceTroubleshooting Motor & ElectricalCutting Operations Replacing Belts To change the main blade arbor V-beltTo change the scoring blade arbor flat belt Blade Tilt To calibrate the blade tiltSquaring Crosscut Fence to Blade To square the crosscut fence with the bladeTo adjust the sliding table parallel with the main blade Sliding Table ParallelismG0460 Electrical Components G0460 Wiring Diagram G0461 Electrical Components G0461 Wiring Diagram at G0461 Wiring Diagram at Parts Main BodyMain Body Parts List DescriptionPW01M Flat Washer 8MM Sliding Table Sliding Table Parts List Crosscut Table Crosscut Table Parts List Description Rip Fence Tilt Assembly Motor Assembly PK42MArbor Assembly Warranty and Returns Warranty Card CommentsGrizzly INDUSTRIAL, INC BOX BELLINGHAM, WA