Appendices T1 ATM Applications, Application Diagram | ADTRAN 616

Total Access 600 Series System Manual	Section 4 User Interface Guide

5.APPENDICES (T1 ATM APPLICATIONS)

The following example is for configuring T1 units with ATM firmware. However, all units using ATM firmware (SDSL, ADSL, SHDSL) may be configured in the same manner. To configure ATM Voice applications with other network types, disregard the T1 Interface Setup Instructions and configure your network interface as needed.

Appendix A. Voice Gateway Quick Start Procedure (Voice Turn Up)

A typical VoATM application (see Figure 7) uses a Total Access 6XX connected to an ATM network. For voice applications, a Voice Gateway is needed to interface with the PSTN. Jetstream, Tollbridge, CopperCom, and LES-CAS are popular Gateway types.

Figure 7. Application Diagram

To configure a Total Access 6XX for use with the Voice Gateway, you need to know the VPI and VCI used on the ATM network to access the Gateway from this Total Access 6XX. You also need to know the format for IDLE CELLS and whether DATA SCRAMBLING is used on this ATM network. The following procedure will help you navigate the Total Access 6XX menus for configuring the necessary elements for VoATM with the Voice Gateway.

Perform the following steps in order to configure the application.

Initial Setup

It is best to configure Total Access 6XX ATM applications by following the order of the top-level menus. For example, first configure the system parameters using the SYSTEM INFO and SYSTEM CONFIG menus. Next, configure the Layer 1 parameters using the INTERFACES menu. Once the Layer 1 information is configured, proceed to the Layer 2 setup using the L2 PROTOCOL menus.

61200624L1-1B

© 2004 ADTRAN, Inc.

169

Image 171

ADTRAN 616, 612, 606, 624, 604 system manual Appendices T1 ATM Applications, Application Diagram

Contents

Total Access 600R Total Access 600 Series Trademarks To the Holder of the ManualAbout this Manual Revision History ConventionsDocument Revision Date Description of Changes Save These Important Safety Instructions Safety Instructions REN/SOC FIC Usoc FCC-Required Information ADTRAN, Inc Affidavit Requirements for Connection to Digital Services FCC Rules and Regulations Canadian Emissions Requirements Industry Canada Compliance Information Pre-Sales Inquiries and Applications Support Repair and Return Installation and Maintenance Support Post-Sale SupportTraining ADTRAN, Inc Table of Contents Table of Contents Total Access 600 Series System Manual System Description Contents System Overview Features and Benefits DTE Interface TestingFrame Relay Support Analog Ports IAD Systems Performance Monitoring Adsl SdslShdsl Tables Equipment DimensionsPower Requirements Reviewing the Front Panel Design At-A-Glance Specifications ADTRAN, Inc Equipment Dimensions Power RequirementsReviewing the Front Panel Design Front Panel LEDs Total Access 604/608 Voice TX/RXLink Data For these LEDs This color light Indicates that Total Access 6XX ATM Front Panel LEDs Total Access 612/616/624 Front Panel Layout Reviewing the Rear Panel Design Total Access 612/616/624 TDM Front Panel LEDs Total Access 604/608 Rear Panel Ntwk Connection Voice Connection PIN Name Description Craft Port Description Connection Battery Backup ConnectionAC Power Connection 10/100BaseT Connection PIN Description Life Line Analog ConnectionDSX-1 Interface Provides the DSX-1 port pinout Lists the unit specifications AT-A-GLANCE Specifications Application Feature Specification Analog Ports Routing EthernetManagement Grounding Instructions Mounting Options Tools Required Unpack and Inspect the System Unpack and Inspect the System This section discusses Total Access 600 Series installationIntroduction Tools Required Grounding Instructions Contents of Adtran Shipments Tools Needed Wallmount InstallationMounting Options Wallmounting the Unit Wallmount Orientation Rackmount Installation Rackmounting the Total Access 612/616/624Supplying Power to the Unit AC Powered Systems User Interface Guide User Interface Guide Total Access 600 Series System Manual Window Panes Navigating the Terminal MenuTerminal Menu Window Menu Path To do this Press this key Right Window Pane NotationThis notation Means that Additional Terminal Menu Window Features Navigating using the Keyboard KeysMoving through the Menus Configuration Keystrokes Session Management KeystrokesTo do this DS0 Maps Getting HelpMain Menu and System Control Selecting the Appropriate Menu Security Levels Menu DescriptionsMenus Submenus SUB-SUBMENUS Read only Displays the registered Clei code for the unit System Info Read only Displays the current bootcode revision System Config Management Craft Port Password Protect System ConfigSystem Config Management System Config Management Craft Port System Config Management Craft Port Parity System Config Management Craft Port Idle TimeSystem Config Management Craft Port Baud Rate System Config Management Craft Port Data Bits System Config Management Telnet Access User List System Config Management Telnet Access AccessSystem Config Management Telnet Access Authen Method System Config Management Telnet Port Displays the TCP port used for this Telnet session Cannot reset the unit or enter terminal modeSystem Config Management Telnet Access Active Sessions Displays the assigned user name System Config Management Snmp Management Trap Delay System Config Management Telnet Access IP Access ListSystem Config Management Snmp Management System Config Management Snmp Management Access System Config Management FDL Management System Config Management Snmp Management Traps System Config Management FDL Management FAR-END IP Address System Config Management FDL Management ModeSystem Config Management FDL Management Link IP Address System Config Management FDL Management IP Netmask System Config Syslog Syslog IP System Config Syslog Syslog FormatSystem Config Syslog Syslog Facility Syslog using Terminal Mode This parameter is for Adtran internal use only System Config Syslog L1 Level System Config Syslog Tollbrg LevelSystem Config Syslog Cmcp Level System Config Syslog Sdsl Level System Config Syslog Coppercom Level System Config Syslog Pots LevelSystem Config Syslog Lescas Level System Config Syslog ATM Level Minimum required level for sending Filter log messages Factory default is GMT-6 Central System Config Network Time Status System Config Network Time Adjust for Daylight SavingSystem Config Network Time Host Address System Config Network Time Refresh Use this activator to cancel any Tftp transfer in progress Indicates the status of the previous update Indicates the current status of the update View the CPU utilization stats from this menu System Utility System UtilizationSystem Utility System Utilization Performance Percentage loss based on ping returned from host read only Activator to start and cancel a ping testTotal packets sent read only Total packets received read only Activates the traceroute process Example usage ping 10.0.0.5 r 10 si 1500 so eth0 n Interfaces Interfaces T1 ConfigInterfaces T1 Config Timing Mode Interfaces T1 Config Format Displays the T1 performance data Displays current alarms and alarm history for T1 interface Indicates whether a test is in progress Interfaces Shdsl Status NTU/LTU Mode Interfaces Shdsl Config NTU/LTU ModeInterfaces Shdsl Config ITU-T/GSPAN Interfaces Shdsl Config Radsl AUTO/FIXED Internal Adtran use only Interfaces Sdsl Config DslamInterfaces Sdsl Config Dslam Setup Configure the Dslam settings from this menu Interfaces Sdsl Status Sdsl Rate Interfaces Adsl Status SNR dBInterfaces Network Adsl Interfaces DSX Interfaces DSX Status Performance Current and Totals FS Interfaces DSX Status Performance Current and Totals ESInterfaces DSX Status Performance Current and Totals SES Interfaces DSX Status Performance Current and Totals SEF Interfaces DSX Status Alarms Clear History Interfaces DSX Status AlarmsInterfaces DSX Status Alarms Current Alarms Interfaces DSX Status Alarms Alarm History Configure the various Ethernet parameters from this menu Interfaces ETHDisplays the Ethernet status information Interfaces FXS Configure the DTE leads from this menuView the status of the DTE leads from this menu These options are used to loopback tests Indicates the port of the FXS module Choices are given below. Default is Loop StartInterfaces FXS Config Port Interfaces FXS Config Mode Interfaces FXS Config Batt Mode Interfaces FXS Config SVC ModeInterfaces FXS Config Line Z Interfaces FXS Config MSG IND Displays the port number Displays the status of the FXS signal bits Choices are given below. Default is None This option indicates whether a test is in progressInterfaces FXO Indicates the port of the FXO module Displays the status of the FXO signal bits Interfaces FXO Status RA SIG Interfaces FXO Status PortInterfaces FXO Status TA SIG Interfaces FXO Status TB SIG L2 Protocol TDM Firmware L2 Protocol TDM T1 Protocol Hdlc L2 Protocol TDM T1 ProtocolL2 Protocol TDM T1 Protocol PPP L2 Protocol TDM T1 Protocol FRE L2 Protocol TDM-T1-PPP Config PPP MAX Config L2 Protocol T1 TDM-T1-PPP ConfigL2 Protocol TDM-T1-PPP Config Mode L2 Protocol TDM-T1-PPP Config PPP L2 Protocol TDM-T1-PPP Config PPP Force Peer IP Address L2 Protocol TDM-T1-PPP Config PPP MAX Timer SECL2 Protocol TDM-T1-PPP Config PPP MAX Failure L2 Protocol TDM-T1-PPP Config PPP Keepalive Period L2 Protocol TDM-T1-PPP Status RX Bytes L2 Protocol TDM-T1-FRE ConfigL2 Protocol TDM-T1-PPP Status RX Pkts L2 Protocol TDM-T1-PPP Status TX Bytes L2 Protocol TDM-T1-FRE Config Dlci Mapping Active L2 Protocol TDM-T1-FRE Config Polling FrequencyL2 Protocol TDM-T1-FRE Config Dlci Mapping L2 Protocol TDM-T1-FRE Config Dlci Mapping NUM L2 Protocol TDM-T1-FRE Status L2 Protocol TDM-T1-FRE Config Dlci Mapping InterfaceL2 Protocol TDM-T1-FRE Config Dlci Mapping Dlci L2 Protocol TDM-T1-FRE Config Dlci Mapping Mode L2 Protocol TDM-T1-FRE Status Port Drop Invalid Dlci L2 Protocol TDM-T1-FRE Status Port Current Util %L2 Protocol TDM-T1-FRE Status Port Average Util % L2 Protocol TDM-T1-FRE Status Port Drop Unknown Dlci L2 Protocol TDM-T1-FRE Status Pvcs TX Bytes L2 Protocol TDM-T1-FRE Status Pvcs StateL2 Protocol TDM-T1-FRE Status Pvcs TX Frames L2 Protocol TDM-T1-FRE Status Pvcs RX Frames L2 Protocol TDM-T1-HDLC Status TX Bytes L2 Protocol TDM-T1-HDLC StatusL2 Protocol TDM-T1-HDLC Status TX Pkts L2 Protocol TDM-T1-HDLC Status RX Pkts L2 Protocol TDM-T1-AUTO Status RX Pkts L2 Protocol TDM-T1-AUTO StatusL2 Protocol TDM-T1-AUTO Status State L2 Protocol TDM-T1-AUTO Status TX Pkts L2 Protocol ATM Firmware L2 Protocol ATM NET Protocol L2 Protocol ATM-NET-ATM ConfigL2 Protocol ATM-NET-ATM Config ATM Config L2 Protocol ATM-NET-ATM Config ATM Config Idle Cells L2 Protocol ATM-NET-ATM Config PVC Config Active L2 Protocol ATM-NET-ATM Config ATM Config HEC CosetL2 Protocol ATM-NET-ATM Config PVC Config L2 Protocol ATM-NET-ATM Config PVC Config NUM L2 Protocol ATM-NET-ATM Config PVC Config VCI L2 Protocol ATM-NET-ATM Config PVC Config ConnectionL2 Protocol ATM-NET-ATM Config PVC Config Setup Router PPP EAP only L2 Protocol ATM-NET-ATM Config PVC Config Setup Connection V35 Setup Setup Connection Voice Setup LES-CAS GW SIM L2 Protocol ATM-NET-ATM Config PVC Config Setup VoiceL2 Protocol ATM-NET-ATM Config PVC Config QOS Connection V35 Setup Setup UNI Dlci L2 Protocol ATM-NET-ATM Status L2 Protocol ATM-NET-ATM Status ATM StatusL2 Protocol ATM-NET-ATM Status ATM Status Clear Stats L2 Protocol ATM-NET-ATM Status PVC Status AAL Stats L2 Protocol ATM-NET-ATM Status PVC StatusL2 Protocol ATM-NET-ATM Status PVC Status NUM L2 Protocol ATM-NET-ATM Status PVC Status SUB-INTERFACE Indicates an EOC cell was received with a voice designation CRC ErrorsRX AAL2 HEC Errors L2 Protocol T1 ATM-T1-ATM Status PVC Status Protocol Status Pots Stats L2 Protocol ATM-NET-CUMTN ConfigClears all recorded statistics and returns all counters to L2 Protocol ATM Firmware Network Interface Cumtn FRE L2 Protocol ATM-NET-CUMTN Config Dlci L2 Protocol ATM-NET-CUMTN Config NUML2 Protocol ATM-NET-CUMTN Config Active L2 Protocol ATM-NET-CUMTN Config Interface L2 Protocol ATM-NET-CUMTN Status Dlci State L2 Protocol ATM V35 ConfigL2 Protocol ATM V35 Config UNI Maint Protocol L2 Protocol ATM V35 Config UNI Poll Timeout T392 L2 Protocol V352-ATM Status Pvcs L2 Protocol ATM V35 Status Port Configures the voice parameters for the interface L2 Protocol ATM DSX ConfigInterfaces ATM DSX Config TX OAM Interfaces ATM DSX Config RX OAM L2 Protocol ALL-ETH-802.3 Protocol L2 Protocol ALL-ETH-802.3 ConfigL2 Protocol ALL-ETH-802.3 Config Mode L2 Protocol ALL-ETH-802.3 Status TX Errors L2 Protocol ALL-ETH-802.3 Status NON-ALIGNED L2 Protocol ALL-ETH-802.3 Status RX ErrorsL2 Protocol ALL-ETH-802.3 Status Crcs L2 Protocol ALL-ETH-802.3 Status RX Collisions View the bridge table status from this menu Configure the Ethernet Bridging parameters from this menuConfigure the bridge table parameters from this menu View the bridging statistics from this menu Router Only routes not learned from this circuit are advertised Use this menu to enable RIP on the LAN interfaceRouter Config Interfaces ETH SUB-INTERFACE Router Config Interfaces ETH Setup This is the mask for the network. Default is Enter the secret used by RIP version 2 hereDisplays the index number in the secondary IP list This Selection enables IP on this PVC NAT MTU Icmp Doom Type of protocol active on the translation Private IP address of the active translationPublic IP address of the active translation Server IP address of the public device Napt Address Number of inbound packets using this translationNumber of outbound packets using this translation Use this menu to enable RIP on this interface Use this menu to set up the Dhcp server Use this menu to enter static routes to other networksDisplays the index number in the static route table Use this menu to enable the Dhcp server on or OFF Router Config Dhcp Server Dhcp ServerRouter Config Dhcp Server Dhcp Address Pools Nbns Server SEC DNS Server PRIDNS Server SEC Nbns Server PRI Router Config UDP Relay Mode Router Config Dhcp Server Exclusion RangesRouter Config Dhcp Server Global Server Options Router Config UDP Relay Host or router to receive this packet This lists the contents of the unit’s IP route tableNetwork or host destination address Network mask applied to the destination address View the IP statistics from this menu IP packets from the units IP stack Setting this activator clears the IP Statistics Number of IP datagrams successfully reassembledPacket the unit couldnt route Number of Icmp Source Quench messages received Number of Icmp Parameter Problem messages receivedNumber of Icmp Destination Unreachable messages received Number of Icmp Time Exceeded messages received Number of Icmp Time Exceeded messages sent Number of Icmp Parameter Problem messages sentNumber of Icmp Address Mask Reply messages received Number of Icmp Destination Unreachable messages sent View the UDP statistics from this menu Number of Icmp Address Mask Request messages sentNumber of Icmp Address Mask Reply messages sent Selecting this activator will clear the Icmp statistics Router Status IP Stats TCP View the TCP statistics from this menu Remote IP address of the TCP connection Selecting this activator clears the TCP statisticsLocal IP address of the TCP connection Local port of the TCP connection Minutes since entry was first entered into the ARP cache Ethernet address resolved 0=no resolutionConfigure the filter characteristics from this menu IP address used for resolving MAC address Indicates the entry number in the MAC Filter Defines table Security Filters Filter DefinesSecurity Filters Filter Defines MAC Filter Defines Indicates the entry number in the IP Filter Defines table Security Filters Filter Defines Pattern Filter DefinesSecurity Filters Filter Defines IP Filter Defines 0.0 TCP Estab Security Filters InterfacesSecurity Filters Interfaces SUB-INTERFACE MAC Turns this entry active when set to YES. Default is noSelects the filter define list to reference default is MAC Security Filters Interfaces SET-UP Last filter to combination Logically and this filter with the next filter in the listLogically or this filter with the next filter in the list Security Radius Server Secret Security Radius ServerSecurity Radius Server Server Security Radius Server UDP Port DS0 Maps Menu Security Radius Server Retry Count Displays the network T1 time slot to be assigned DS0 Maps EDIT/VIEW MAP 1 DS0 DS0 Maps EDIT/VIEW MAP 1 RBS T1 Interface Setup Instructions Step Action Appendix A. Configuring the Unit for RoutingInitial Setup Setting up the Interfaces Configuring the Layer 2 Protocol Ethernet Interface Setup InstructionsLayer 2 Protocol FRE Configuration T1 Interface Step Action Layer 2 Protocol PPP Configuration T1 Interface Step Action Layer 2 Protocol FRE Configuration T1 Interface For the entry to delete and press the D key Setting the Router OptionsLayer 2 Protocol Configuration Ethernet Interface Router Options Ethernet Interface Mapping the DS0s Router Options Setting the Default Gateway Step Action 61200624L1-1B ADTRAN, Inc 157 Appendix B. Configuring the Unit for Bridging 61200624L1-1B ADTRAN, Inc 159 160 ADTRAN, Inc Verifying the Bridge Options Bridge Options Step ActionDS0 Mapping Instructions Step Action 162 ADTRAN, Inc Network T1 menus beginning on FXS menus beginning on Appendix C. Configuring the Unit for Voice Applications FXS Interface Setup Instructions Step Action FXS Interface Setup Instructions Network T1 menus beginning on DSX-1 menus beginning on Appendix D. Configuring the Unit for DSX-1 Applications DSX-1 Interface Setup Instructions Step Action T1 Interface Setup Instructions 168 ADTRAN, Inc Appendices T1 ATM Applications Application Diagram 170 ADTRAN, Inc SWITCH, Entered by selecting V Oice under the C Onnection field Layer 2 Protocol Configuration T1 InterfaceEnter the I DLE C Ells format for your network Set D ATA S Crambling appropriately for your network 61200624L1-1B ADTRAN, Inc 173 Appendix B. RFC1483 Quick Start IP Routing 61200624L1-1B ADTRAN, Inc 175 ATM-NET-ATM Config PVC Config Setup Router on page 103 for Layer 2 Protocol ATM Configuration T1 Interface Router Options T1 Interface L2 Protocol = ATM Step Action Router Options Ethernet Interface Step Action Router Options T1 Interface L2 Protocol = ATM IP Routing with NAT Appendix C. RFC1483 Quick Start IP Routing with NAT Appendix D. RFC 1483 Quick Start Bridging PVC Config Setup Router on page 103 for more details Bridge menus beginning on Detail Level Procedures 184 ADTRAN, Inc Tools and Materials Required DLP-1 Connecting a VT100 Terminal or PC to the Craft PortPrerequisite Procedures Introduction Perform the steps below in the order listed DLP-2 Logging in to the System DLP-2 Total Access 600 Series System Manual IP Address Subnet Mask User guest Password password DLP-3 Setting IP Parameters DLP-3 Total Access 600 Series System Manual DLP-4 Verifying Communications Over an IP LAN Access to a PC or other computer connected to the LAN DLP-4 Total Access 600 Series System Manual Total Access 600 Series System Manual DLP-4 194 ADTRAN, Inc DLP-5 Connecting to the Unit Using Telnet DLP-5 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 197 198 ADTRAN, Inc 61200624L1-1B ADTRAN, Inc 199 Enter Have read-only permission for all menu items minimum rights 202 ADTRAN, Inc DLP-7 Updating the Firmware using Tftp DLP-7 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 205 206 ADTRAN, Inc DLP-8 Updating the Firmware using Xmodem Updating Firmware via the Console Menus DLP-9 Saving the Current Configuration Using Tftp DLP-9 Total Access 600 Series System Manual DLP-10 Loading a Configuration Using Tftp DLP-10 Total Access 600 Series System Manual Xmodem Perform the following steps in the order listed DLP-12 Loading a Configuration Using Xmodem DLP-12 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 217 Do not enter further key commands until completing Step Saving the Total Access 6XX configuration Entering commands at the command prompt Loading a configuration into the Total Access 220 ADTRAN, Inc DLP-14 A.03 to A.04 Firmware Upgrade Upgrade From A.03 to A.04 Directly Upgrade From A.03 to A.03.92 Transition Build to A.04 DLP-15 Using the Adtran Utility Syslog Setting Up the Syslog Host Setting up the Total Access 6XX to use Syslog Additional Syslog Features 226 ADTRAN, Inc DLP-16 Executing Terminal Mode Commands Example usage ping 10.0.0.5 r 10 si 1500 so eth0 n Fstimer start x x is in seconds or fstimer stop Telnet hostname/address port Example usage trace 10.0.0.5 h 20 t 1 r 1 so eth0 230 ADTRAN, Inc DLP-17 Configuring Dual T1 Maps Dual T1 Map Primary T1 Map DSX Map can be mapped to the FXS and FXO access modules only DLP-18 Unit Installation Using the Auto-Config Feature DLP-18 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 237 238 ADTRAN, Inc Purchase the EC/ADPCM P/N 1200613L1 DLP-19 TDM to ATM Upgrade DLP-19 Total Access 600 Series System Manual System Info Firmware Revision field does not display Error 242 ADTRAN, Inc Status Field Meter Field Log Field Telnet UtilityVT100 Utility Tftp Server Telnet Menu Tree Telnet Utility Connect Session MenuClick on Session to open the Telnet session Establishes the Telnet session Edit Menu Options MenuCapture Menu Opens the online help Provides online help for using the Adtran UtilitiesHelp Menu VT100 Utility Port Menu Tftp Server Identical to the Telnet Capture Menu see Capture Menu onOpens online help Print Log Server Menu LOG Field HelpStatus Field Meter Field 252 ADTRAN, Inc Mibs Mibs Supported by TDM Units Standard RFC MIBsEnterprise MIBs Traps Supported by TDM Units MIB Compilation Order for TDM Units Mibs Supported by ATM Units MIB Variables Supported by TDM Units Udp Tcp Dsx1 Egp 61200624L1-1B ADTRAN, Inc 259 Atm Snmp 61200624L1-1B ADTRAN, Inc 261 262 ADTRAN, Inc