Number of Icmp Address Mask Reply messages received | ADTRAN 604

Total Access 600 Series System Manual	Section 4 User Interface Guide

ICMP ADDRESS MASK REPLY MSGS RCVD

The number of ICMP Address Mask Reply messages received.

ICMP MESSAGES SENT

The total number of ICMP messages this unit attempted to send. Note that this counter includes all those counted by ICMP PACKET ERRORS.

ICMP PACKET ERRORS

The number of packets the unit did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value.

ICMP DEST. UNREACHABLE MSGS SENT

The number of ICMP Destination Unreachable messages sent.

ICMP TIME EXCEEDED MSGS SENT

The number of ICMP Time Exceeded messages sent.

ICMP PARAMETER PROBLEM MSGS SENT

The number of ICMP Parameter Problem messages sent.

ICMP SOURCE QUENCH MSGS SENT

The number of ICMP Source Quench messages sent.

ICMP REDIRECT MSGS SENT

The number of ICMP Redirect messages sent.

ICMP ECHO REQUEST MSGS SENT

The number of ICMP Echo (request) messages sent.

ICMP ECHO REPLY MSGS SENT

The number of ICMP Echo Reply messages sent.

ICMP TIMESTAMP REQUEST MSGS SENT

The number of ICMP Timestamp (request) messages sent.

ICMP TIMESTAMP REPLY MSGS SENT

The number of ICMP Timestamp Reply messages sent.

61200624L1-1B

© 2004 ADTRAN, Inc.

137

Image 139

ADTRAN 604, 612 Number of Icmp Address Mask Reply messages received, Number of Icmp Destination Unreachable messages sent

Contents

Total Access 600R Total Access 600 Series To the Holder of the Manual TrademarksAbout this Manual Conventions Revision HistoryDocument Revision Date Description of Changes Save These Important Safety Instructions Safety Instructions REN/SOC FIC Usoc FCC-Required Information ADTRAN, Inc Affidavit Requirements for Connection to Digital Services FCC Rules and Regulations Canadian Emissions Requirements Industry Canada Compliance Information Pre-Sales Inquiries and Applications Support Repair and Return Post-Sale Support Installation and Maintenance SupportTraining ADTRAN, Inc Table of Contents Table of Contents Total Access 600 Series System Manual System Description Contents System Overview Features and Benefits DTE Interface TestingFrame Relay Support Analog Ports IAD Systems Performance Monitoring Sdsl AdslShdsl Tables Equipment DimensionsPower Requirements Reviewing the Front Panel Design At-A-Glance Specifications ADTRAN, Inc Power Requirements Equipment DimensionsReviewing the Front Panel Design Front Panel LEDs Total Access 604/608 Voice TX/RXLink Data For these LEDs This color light Indicates that Total Access 6XX ATM Front Panel LEDs Total Access 612/616/624 Front Panel Layout Reviewing the Rear Panel Design Total Access 612/616/624 TDM Front Panel LEDs Total Access 604/608 Rear Panel Ntwk Connection Voice Connection PIN Name Description Craft Port Description Connection Battery Backup ConnectionAC Power Connection 10/100BaseT Connection PIN Description Life Line Analog ConnectionDSX-1 Interface Provides the DSX-1 port pinout Lists the unit specifications AT-A-GLANCE Specifications Routing Ethernet Application Feature Specification Analog PortsManagement Grounding Instructions Mounting Options Tools Required Unpack and Inspect the System Unpack and Inspect the System This section discusses Total Access 600 Series installationIntroduction Tools Required Grounding Instructions Contents of Adtran Shipments Tools Needed Wallmount InstallationMounting Options Wallmounting the Unit Wallmount Orientation Rackmount Installation Rackmounting the Total Access 612/616/624Supplying Power to the Unit AC Powered Systems User Interface Guide User Interface Guide Total Access 600 Series System Manual Window Panes Navigating the Terminal MenuTerminal Menu Window Menu Path Right Window Pane Notation To do this Press this keyThis notation Means that Navigating using the Keyboard Keys Additional Terminal Menu Window FeaturesMoving through the Menus Session Management Keystrokes Configuration KeystrokesTo do this DS0 Maps Getting HelpMain Menu and System Control Selecting the Appropriate Menu Menu Descriptions Security LevelsMenus Submenus SUB-SUBMENUS Read only Displays the registered Clei code for the unit System Info Read only Displays the current bootcode revision System Config Management Craft Port Password Protect System ConfigSystem Config Management System Config Management Craft Port System Config Management Craft Port Parity System Config Management Craft Port Idle TimeSystem Config Management Craft Port Baud Rate System Config Management Craft Port Data Bits System Config Management Telnet Access User List System Config Management Telnet Access AccessSystem Config Management Telnet Access Authen Method System Config Management Telnet Port Displays the TCP port used for this Telnet session Cannot reset the unit or enter terminal modeSystem Config Management Telnet Access Active Sessions Displays the assigned user name System Config Management Snmp Management Trap Delay System Config Management Telnet Access IP Access ListSystem Config Management Snmp Management System Config Management Snmp Management Access System Config Management FDL Management System Config Management Snmp Management Traps System Config Management FDL Management FAR-END IP Address System Config Management FDL Management ModeSystem Config Management FDL Management Link IP Address System Config Management FDL Management IP Netmask System Config Syslog Syslog Format System Config Syslog Syslog IPSystem Config Syslog Syslog Facility Syslog using Terminal Mode This parameter is for Adtran internal use only System Config Syslog L1 Level System Config Syslog Tollbrg LevelSystem Config Syslog Cmcp Level System Config Syslog Sdsl Level System Config Syslog Coppercom Level System Config Syslog Pots LevelSystem Config Syslog Lescas Level System Config Syslog ATM Level Minimum required level for sending Filter log messages Factory default is GMT-6 Central System Config Network Time Status System Config Network Time Adjust for Daylight SavingSystem Config Network Time Host Address System Config Network Time Refresh Use this activator to cancel any Tftp transfer in progress Indicates the status of the previous update Indicates the current status of the update System Utility System Utilization View the CPU utilization stats from this menuSystem Utility System Utilization Performance Percentage loss based on ping returned from host read only Activator to start and cancel a ping testTotal packets sent read only Total packets received read only Activates the traceroute process Example usage ping 10.0.0.5 r 10 si 1500 so eth0 n Interfaces Interfaces T1 ConfigInterfaces T1 Config Timing Mode Interfaces T1 Config Format Displays the T1 performance data Displays current alarms and alarm history for T1 interface Indicates whether a test is in progress Interfaces Shdsl Status NTU/LTU Mode Interfaces Shdsl Config NTU/LTU ModeInterfaces Shdsl Config ITU-T/GSPAN Interfaces Shdsl Config Radsl AUTO/FIXED Internal Adtran use only Interfaces Sdsl Config DslamInterfaces Sdsl Config Dslam Setup Configure the Dslam settings from this menu Interfaces Adsl Status SNR dB Interfaces Sdsl Status Sdsl RateInterfaces Network Adsl Interfaces DSX Interfaces DSX Status Performance Current and Totals FS Interfaces DSX Status Performance Current and Totals ESInterfaces DSX Status Performance Current and Totals SES Interfaces DSX Status Performance Current and Totals SEF Interfaces DSX Status Alarms Clear History Interfaces DSX Status AlarmsInterfaces DSX Status Alarms Current Alarms Interfaces DSX Status Alarms Alarm History Interfaces ETH Configure the various Ethernet parameters from this menuDisplays the Ethernet status information Interfaces FXS Configure the DTE leads from this menuView the status of the DTE leads from this menu These options are used to loopback tests Indicates the port of the FXS module Choices are given below. Default is Loop StartInterfaces FXS Config Port Interfaces FXS Config Mode Interfaces FXS Config Batt Mode Interfaces FXS Config SVC ModeInterfaces FXS Config Line Z Interfaces FXS Config MSG IND Displays the port number Displays the status of the FXS signal bits This option indicates whether a test is in progress Choices are given below. Default is NoneInterfaces FXO Indicates the port of the FXO module Displays the status of the FXO signal bits Interfaces FXO Status RA SIG Interfaces FXO Status PortInterfaces FXO Status TA SIG Interfaces FXO Status TB SIG L2 Protocol TDM Firmware L2 Protocol TDM T1 Protocol Hdlc L2 Protocol TDM T1 ProtocolL2 Protocol TDM T1 Protocol PPP L2 Protocol TDM T1 Protocol FRE L2 Protocol TDM-T1-PPP Config PPP MAX Config L2 Protocol T1 TDM-T1-PPP ConfigL2 Protocol TDM-T1-PPP Config Mode L2 Protocol TDM-T1-PPP Config PPP L2 Protocol TDM-T1-PPP Config PPP Force Peer IP Address L2 Protocol TDM-T1-PPP Config PPP MAX Timer SECL2 Protocol TDM-T1-PPP Config PPP MAX Failure L2 Protocol TDM-T1-PPP Config PPP Keepalive Period L2 Protocol TDM-T1-PPP Status RX Bytes L2 Protocol TDM-T1-FRE ConfigL2 Protocol TDM-T1-PPP Status RX Pkts L2 Protocol TDM-T1-PPP Status TX Bytes L2 Protocol TDM-T1-FRE Config Dlci Mapping Active L2 Protocol TDM-T1-FRE Config Polling FrequencyL2 Protocol TDM-T1-FRE Config Dlci Mapping L2 Protocol TDM-T1-FRE Config Dlci Mapping NUM L2 Protocol TDM-T1-FRE Status L2 Protocol TDM-T1-FRE Config Dlci Mapping InterfaceL2 Protocol TDM-T1-FRE Config Dlci Mapping Dlci L2 Protocol TDM-T1-FRE Config Dlci Mapping Mode L2 Protocol TDM-T1-FRE Status Port Drop Invalid Dlci L2 Protocol TDM-T1-FRE Status Port Current Util %L2 Protocol TDM-T1-FRE Status Port Average Util % L2 Protocol TDM-T1-FRE Status Port Drop Unknown Dlci L2 Protocol TDM-T1-FRE Status Pvcs TX Bytes L2 Protocol TDM-T1-FRE Status Pvcs StateL2 Protocol TDM-T1-FRE Status Pvcs TX Frames L2 Protocol TDM-T1-FRE Status Pvcs RX Frames L2 Protocol TDM-T1-HDLC Status TX Bytes L2 Protocol TDM-T1-HDLC StatusL2 Protocol TDM-T1-HDLC Status TX Pkts L2 Protocol TDM-T1-HDLC Status RX Pkts L2 Protocol TDM-T1-AUTO Status RX Pkts L2 Protocol TDM-T1-AUTO StatusL2 Protocol TDM-T1-AUTO Status State L2 Protocol TDM-T1-AUTO Status TX Pkts L2 Protocol ATM Firmware L2 Protocol ATM NET Protocol L2 Protocol ATM-NET-ATM ConfigL2 Protocol ATM-NET-ATM Config ATM Config L2 Protocol ATM-NET-ATM Config ATM Config Idle Cells L2 Protocol ATM-NET-ATM Config PVC Config Active L2 Protocol ATM-NET-ATM Config ATM Config HEC CosetL2 Protocol ATM-NET-ATM Config PVC Config L2 Protocol ATM-NET-ATM Config PVC Config NUM L2 Protocol ATM-NET-ATM Config PVC Config Connection L2 Protocol ATM-NET-ATM Config PVC Config VCIL2 Protocol ATM-NET-ATM Config PVC Config Setup Router PPP EAP only L2 Protocol ATM-NET-ATM Config PVC Config Setup Connection V35 Setup Setup Connection Voice Setup LES-CAS GW SIM L2 Protocol ATM-NET-ATM Config PVC Config Setup VoiceL2 Protocol ATM-NET-ATM Config PVC Config QOS Connection V35 Setup Setup UNI Dlci L2 Protocol ATM-NET-ATM Status ATM Status L2 Protocol ATM-NET-ATM StatusL2 Protocol ATM-NET-ATM Status ATM Status Clear Stats L2 Protocol ATM-NET-ATM Status PVC Status AAL Stats L2 Protocol ATM-NET-ATM Status PVC StatusL2 Protocol ATM-NET-ATM Status PVC Status NUM L2 Protocol ATM-NET-ATM Status PVC Status SUB-INTERFACE Indicates an EOC cell was received with a voice designation CRC ErrorsRX AAL2 HEC Errors L2 Protocol T1 ATM-T1-ATM Status PVC Status Protocol Status Pots Stats L2 Protocol ATM-NET-CUMTN ConfigClears all recorded statistics and returns all counters to L2 Protocol ATM Firmware Network Interface Cumtn FRE L2 Protocol ATM-NET-CUMTN Config Dlci L2 Protocol ATM-NET-CUMTN Config NUML2 Protocol ATM-NET-CUMTN Config Active L2 Protocol ATM-NET-CUMTN Config Interface L2 Protocol ATM-NET-CUMTN Status Dlci State L2 Protocol ATM V35 ConfigL2 Protocol ATM V35 Config UNI Maint Protocol L2 Protocol ATM V35 Config UNI Poll Timeout T392 L2 Protocol V352-ATM Status Pvcs L2 Protocol ATM V35 Status Port Configures the voice parameters for the interface L2 Protocol ATM DSX ConfigInterfaces ATM DSX Config TX OAM Interfaces ATM DSX Config RX OAM L2 Protocol ALL-ETH-802.3 Protocol L2 Protocol ALL-ETH-802.3 ConfigL2 Protocol ALL-ETH-802.3 Config Mode L2 Protocol ALL-ETH-802.3 Status TX Errors L2 Protocol ALL-ETH-802.3 Status NON-ALIGNED L2 Protocol ALL-ETH-802.3 Status RX ErrorsL2 Protocol ALL-ETH-802.3 Status Crcs L2 Protocol ALL-ETH-802.3 Status RX Collisions View the bridge table status from this menu Configure the Ethernet Bridging parameters from this menuConfigure the bridge table parameters from this menu View the bridging statistics from this menu Router Only routes not learned from this circuit are advertised Use this menu to enable RIP on the LAN interfaceRouter Config Interfaces ETH SUB-INTERFACE Router Config Interfaces ETH Setup Enter the secret used by RIP version 2 here This is the mask for the network. Default isDisplays the index number in the secondary IP list This Selection enables IP on this PVC NAT MTU Icmp Doom Type of protocol active on the translation Private IP address of the active translationPublic IP address of the active translation Server IP address of the public device Napt Address Number of inbound packets using this translationNumber of outbound packets using this translation Use this menu to enable RIP on this interface Use this menu to enter static routes to other networks Use this menu to set up the Dhcp serverDisplays the index number in the static route table Router Config Dhcp Server Dhcp Server Use this menu to enable the Dhcp server on or OFFRouter Config Dhcp Server Dhcp Address Pools Nbns Server SEC DNS Server PRIDNS Server SEC Nbns Server PRI Router Config UDP Relay Mode Router Config Dhcp Server Exclusion RangesRouter Config Dhcp Server Global Server Options Router Config UDP Relay Host or router to receive this packet This lists the contents of the unit’s IP route tableNetwork or host destination address Network mask applied to the destination address View the IP statistics from this menu IP packets from the units IP stack Number of IP datagrams successfully reassembled Setting this activator clears the IP StatisticsPacket the unit couldnt route Number of Icmp Source Quench messages received Number of Icmp Parameter Problem messages receivedNumber of Icmp Destination Unreachable messages received Number of Icmp Time Exceeded messages received Number of Icmp Time Exceeded messages sent Number of Icmp Parameter Problem messages sentNumber of Icmp Address Mask Reply messages received Number of Icmp Destination Unreachable messages sent View the UDP statistics from this menu Number of Icmp Address Mask Request messages sentNumber of Icmp Address Mask Reply messages sent Selecting this activator will clear the Icmp statistics Router Status IP Stats TCP View the TCP statistics from this menu Remote IP address of the TCP connection Selecting this activator clears the TCP statisticsLocal IP address of the TCP connection Local port of the TCP connection Minutes since entry was first entered into the ARP cache Ethernet address resolved 0=no resolutionConfigure the filter characteristics from this menu IP address used for resolving MAC address Security Filters Filter Defines Indicates the entry number in the MAC Filter Defines tableSecurity Filters Filter Defines MAC Filter Defines Security Filters Filter Defines Pattern Filter Defines Indicates the entry number in the IP Filter Defines tableSecurity Filters Filter Defines IP Filter Defines 0.0 Security Filters Interfaces TCP EstabSecurity Filters Interfaces SUB-INTERFACE MAC Turns this entry active when set to YES. Default is noSelects the filter define list to reference default is MAC Security Filters Interfaces SET-UP Logically and this filter with the next filter in the list Last filter to combinationLogically or this filter with the next filter in the list Security Radius Server Secret Security Radius ServerSecurity Radius Server Server Security Radius Server UDP Port DS0 Maps Menu Security Radius Server Retry Count Displays the network T1 time slot to be assigned DS0 Maps EDIT/VIEW MAP 1 DS0 DS0 Maps EDIT/VIEW MAP 1 RBS T1 Interface Setup Instructions Step Action Appendix A. Configuring the Unit for RoutingInitial Setup Setting up the Interfaces Ethernet Interface Setup Instructions Configuring the Layer 2 ProtocolLayer 2 Protocol FRE Configuration T1 Interface Step Action Layer 2 Protocol PPP Configuration T1 Interface Step Action Layer 2 Protocol FRE Configuration T1 Interface For the entry to delete and press the D key Setting the Router OptionsLayer 2 Protocol Configuration Ethernet Interface Router Options Ethernet Interface Mapping the DS0s Router Options Setting the Default Gateway Step Action 61200624L1-1B ADTRAN, Inc 157 Appendix B. Configuring the Unit for Bridging 61200624L1-1B ADTRAN, Inc 159 160 ADTRAN, Inc Bridge Options Step Action Verifying the Bridge OptionsDS0 Mapping Instructions Step Action 162 ADTRAN, Inc Network T1 menus beginning on FXS menus beginning on Appendix C. Configuring the Unit for Voice Applications FXS Interface Setup Instructions Step Action FXS Interface Setup Instructions Network T1 menus beginning on DSX-1 menus beginning on Appendix D. Configuring the Unit for DSX-1 Applications DSX-1 Interface Setup Instructions Step Action T1 Interface Setup Instructions 168 ADTRAN, Inc Appendices T1 ATM Applications Application Diagram 170 ADTRAN, Inc SWITCH, Entered by selecting V Oice under the C Onnection field Layer 2 Protocol Configuration T1 InterfaceEnter the I DLE C Ells format for your network Set D ATA S Crambling appropriately for your network 61200624L1-1B ADTRAN, Inc 173 Appendix B. RFC1483 Quick Start IP Routing 61200624L1-1B ADTRAN, Inc 175 ATM-NET-ATM Config PVC Config Setup Router on page 103 for Layer 2 Protocol ATM Configuration T1 Interface Router Options T1 Interface L2 Protocol = ATM Step Action Router Options Ethernet Interface Step Action Router Options T1 Interface L2 Protocol = ATM IP Routing with NAT Appendix C. RFC1483 Quick Start IP Routing with NAT Appendix D. RFC 1483 Quick Start Bridging PVC Config Setup Router on page 103 for more details Bridge menus beginning on Detail Level Procedures 184 ADTRAN, Inc Tools and Materials Required DLP-1 Connecting a VT100 Terminal or PC to the Craft PortPrerequisite Procedures Introduction Perform the steps below in the order listed DLP-2 Logging in to the System DLP-2 Total Access 600 Series System Manual IP Address Subnet Mask User guest Password password DLP-3 Setting IP Parameters DLP-3 Total Access 600 Series System Manual DLP-4 Verifying Communications Over an IP LAN Access to a PC or other computer connected to the LAN DLP-4 Total Access 600 Series System Manual Total Access 600 Series System Manual DLP-4 194 ADTRAN, Inc DLP-5 Connecting to the Unit Using Telnet DLP-5 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 197 198 ADTRAN, Inc 61200624L1-1B ADTRAN, Inc 199 Enter Have read-only permission for all menu items minimum rights 202 ADTRAN, Inc DLP-7 Updating the Firmware using Tftp DLP-7 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 205 206 ADTRAN, Inc DLP-8 Updating the Firmware using Xmodem Updating Firmware via the Console Menus DLP-9 Saving the Current Configuration Using Tftp DLP-9 Total Access 600 Series System Manual DLP-10 Loading a Configuration Using Tftp DLP-10 Total Access 600 Series System Manual Xmodem Perform the following steps in the order listed DLP-12 Loading a Configuration Using Xmodem DLP-12 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 217 Do not enter further key commands until completing Step Saving the Total Access 6XX configuration Entering commands at the command prompt Loading a configuration into the Total Access 220 ADTRAN, Inc DLP-14 A.03 to A.04 Firmware Upgrade Upgrade From A.03 to A.04 Directly Upgrade From A.03 to A.03.92 Transition Build to A.04 DLP-15 Using the Adtran Utility Syslog Setting Up the Syslog Host Setting up the Total Access 6XX to use Syslog Additional Syslog Features 226 ADTRAN, Inc DLP-16 Executing Terminal Mode Commands Example usage ping 10.0.0.5 r 10 si 1500 so eth0 n Fstimer start x x is in seconds or fstimer stop Telnet hostname/address port Example usage trace 10.0.0.5 h 20 t 1 r 1 so eth0 230 ADTRAN, Inc DLP-17 Configuring Dual T1 Maps Dual T1 Map Primary T1 Map DSX Map can be mapped to the FXS and FXO access modules only DLP-18 Unit Installation Using the Auto-Config Feature DLP-18 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 237 238 ADTRAN, Inc Purchase the EC/ADPCM P/N 1200613L1 DLP-19 TDM to ATM Upgrade DLP-19 Total Access 600 Series System Manual System Info Firmware Revision field does not display Error 242 ADTRAN, Inc Status Field Meter Field Log Field Telnet UtilityVT100 Utility Tftp Server Telnet Menu Tree Telnet Utility Connect Session MenuClick on Session to open the Telnet session Establishes the Telnet session Options Menu Edit MenuCapture Menu Opens the online help Provides online help for using the Adtran UtilitiesHelp Menu VT100 Utility Port Menu Identical to the Telnet Capture Menu see Capture Menu on Tftp ServerOpens online help Print Log Server Menu LOG Field HelpStatus Field Meter Field 252 ADTRAN, Inc Mibs Standard RFC MIBs Mibs Supported by TDM UnitsEnterprise MIBs Traps Supported by TDM Units MIB Compilation Order for TDM Units Mibs Supported by ATM Units MIB Variables Supported by TDM Units Udp Tcp Dsx1 Egp 61200624L1-1B ADTRAN, Inc 259 Atm Snmp 61200624L1-1B ADTRAN, Inc 261 262 ADTRAN, Inc