DLP-19 Total Access 600 Series System Manual | ADTRAN 606, 612, 616

Section 5 DLP-19	Total Access 600 Series System Manual

Perform the steps below in the order listed.

The upgrade package may be purchased from ADTRAN. This package includes the EC/ADPCM (P/N 1200613L1) and the ADTRAN installation and test. If this package is ordered, the customer must send the Total Access TDM 612/616/624 unit back to ADTRAN. Once received, the EC/ADPCM module is installed along with the latest VoATM firmware. The upgraded unit is then tested and returned to the customer. Please call ADTRAN CAPs department at 800-9-ADTRAN extension 7722 for this service.

Purchase and Installation of the EC/ADPCM Module by the Customer

An EC/ADPCM module may be purchased separately and installed in the Total Access 612/616/624 T1 TDM unit by the customer.

1.Remove power from the Total Access 612/616/624.

2.Remove the screws from the back of the Total Access 612/616/624, and then remove the cover.

3.Install the EC/ADPCM Module in the Total Access 612/616/624 as shown in the following figure.

Network	Card
Network			Card
		FXS	Card
		FXS
EC/ADPCM Card
(Installed and secured)

4.Remove the two screws from the motherboard, install the two standoffs, and insert the screws through the top the EC/ADPCM board into the standoffs.

5.Replace the cover on the Total Access 612/616/624 and tighten the screws.

6.Restore power to the Total Access 612/616/624.

7.Obtain the latest VoATM firmware from the ADTRAN website (http://www.ADTRAN.com). Select

SUPPORT > POST-SALES TECHNICAL SUPPORT > FIRMWARE UPDATES > 612/616/624 ATM or contact Post-Sales Technical Support at 888-4ADTRAN.

8.Upgrade the Total Access 612/616/624 with the latest VoATM firmware (see Updating the Firmware using TFTP and DLP-8,Updating the Firmware using XMODEM for details on upgrading the firmware).

240

© 2004 ADTRAN, Inc.

61200624L1-1B

Image 242

ADTRAN 606, 612, 616, 624, 604 system manual DLP-19 Total Access 600 Series System Manual

Contents

Total Access 600 Series Total Access 600R About this Manual TrademarksTo the Holder of the Manual Document Revision Date Description of Changes Revision HistoryConventions Safety Instructions Save These Important Safety Instructions FCC-Required Information REN/SOC FIC Usoc ADTRAN, Inc Affidavit Requirements for Connection to Digital Services FCC Rules and Regulations Industry Canada Compliance Information Canadian Emissions Requirements Repair and Return Pre-Sales Inquiries and Applications Support Training Installation and Maintenance SupportPost-Sale Support ADTRAN, Inc Table of Contents Table of Contents Total Access 600 Series System Manual Contents System Description System Overview Features and Benefits Analog Ports TestingFrame Relay Support DTE Interface Performance Monitoring IAD Systems Shdsl AdslSdsl At-A-Glance Specifications Equipment DimensionsPower Requirements Reviewing the Front Panel Design Tables ADTRAN, Inc Reviewing the Front Panel Design Equipment DimensionsPower Requirements Total Access 604/608 Front Panel LEDs Data TX/RXLink Voice Total Access 6XX ATM Front Panel LEDs For these LEDs This color light Indicates that Total Access 612/616/624 Front Panel Layout Total Access 612/616/624 TDM Front Panel LEDs Reviewing the Rear Panel Design Total Access 604/608 Rear Panel Voice Connection Ntwk Connection Craft Port PIN Name Description Description 10/100BaseT Connection Battery Backup ConnectionAC Power Connection Connection Provides the DSX-1 port pinout Life Line Analog ConnectionDSX-1 Interface PIN Description AT-A-GLANCE Specifications Lists the unit specifications Management Application Feature Specification Analog PortsRouting Ethernet Tools Required Unpack and Inspect the System Grounding Instructions Mounting Options Tools Required This section discusses Total Access 600 Series installationIntroduction Unpack and Inspect the System Contents of Adtran Shipments Grounding Instructions Wallmounting the Unit Wallmount InstallationMounting Options Tools Needed Wallmount Orientation AC Powered Systems Rackmounting the Total Access 612/616/624Supplying Power to the Unit Rackmount Installation User Interface Guide User Interface Guide Total Access 600 Series System Manual Menu Path Navigating the Terminal MenuTerminal Menu Window Window Panes This notation Means that To do this Press this keyRight Window Pane Notation Moving through the Menus Additional Terminal Menu Window FeaturesNavigating using the Keyboard Keys To do this Configuration KeystrokesSession Management Keystrokes Selecting the Appropriate Menu Getting HelpMain Menu and System Control DS0 Maps Menus Submenus SUB-SUBMENUS Security LevelsMenu Descriptions System Info Read only Displays the registered Clei code for the unit Read only Displays the current bootcode revision System Config Management Craft Port System ConfigSystem Config Management System Config Management Craft Port Password Protect System Config Management Craft Port Data Bits System Config Management Craft Port Idle TimeSystem Config Management Craft Port Baud Rate System Config Management Craft Port Parity System Config Management Telnet Port System Config Management Telnet Access AccessSystem Config Management Telnet Access Authen Method System Config Management Telnet Access User List Displays the assigned user name Cannot reset the unit or enter terminal modeSystem Config Management Telnet Access Active Sessions Displays the TCP port used for this Telnet session System Config Management Snmp Management Access System Config Management Telnet Access IP Access ListSystem Config Management Snmp Management System Config Management Snmp Management Trap Delay System Config Management Snmp Management Traps System Config Management FDL Management System Config Management FDL Management IP Netmask System Config Management FDL Management ModeSystem Config Management FDL Management Link IP Address System Config Management FDL Management FAR-END IP Address System Config Syslog Syslog Facility System Config Syslog Syslog IPSystem Config Syslog Syslog Format Syslog using Terminal Mode This parameter is for Adtran internal use only System Config Syslog Sdsl Level System Config Syslog Tollbrg LevelSystem Config Syslog Cmcp Level System Config Syslog L1 Level System Config Syslog ATM Level System Config Syslog Pots LevelSystem Config Syslog Lescas Level System Config Syslog Coppercom Level Factory default is GMT-6 Central Minimum required level for sending Filter log messages System Config Network Time Refresh System Config Network Time Adjust for Daylight SavingSystem Config Network Time Host Address System Config Network Time Status Use this activator to cancel any Tftp transfer in progress Indicates the current status of the update Indicates the status of the previous update System Utility System Utilization Performance View the CPU utilization stats from this menuSystem Utility System Utilization Total packets received read only Activator to start and cancel a ping testTotal packets sent read only Percentage loss based on ping returned from host read only Activates the traceroute process Example usage ping 10.0.0.5 r 10 si 1500 so eth0 n Interfaces T1 Config Format Interfaces T1 ConfigInterfaces T1 Config Timing Mode Interfaces Displays the T1 performance data Displays current alarms and alarm history for T1 interface Indicates whether a test is in progress Interfaces Shdsl Config Radsl AUTO/FIXED Interfaces Shdsl Config NTU/LTU ModeInterfaces Shdsl Config ITU-T/GSPAN Interfaces Shdsl Status NTU/LTU Mode Configure the Dslam settings from this menu Interfaces Sdsl Config DslamInterfaces Sdsl Config Dslam Setup Internal Adtran use only Interfaces Network Adsl Interfaces Sdsl Status Sdsl RateInterfaces Adsl Status SNR dB Interfaces DSX Interfaces DSX Status Performance Current and Totals SEF Interfaces DSX Status Performance Current and Totals ESInterfaces DSX Status Performance Current and Totals SES Interfaces DSX Status Performance Current and Totals FS Interfaces DSX Status Alarms Alarm History Interfaces DSX Status AlarmsInterfaces DSX Status Alarms Current Alarms Interfaces DSX Status Alarms Clear History Displays the Ethernet status information Configure the various Ethernet parameters from this menuInterfaces ETH These options are used to loopback tests Configure the DTE leads from this menuView the status of the DTE leads from this menu Interfaces FXS Interfaces FXS Config Mode Choices are given below. Default is Loop StartInterfaces FXS Config Port Indicates the port of the FXS module Interfaces FXS Config MSG IND Interfaces FXS Config SVC ModeInterfaces FXS Config Line Z Interfaces FXS Config Batt Mode Displays the status of the FXS signal bits Displays the port number Interfaces FXO Choices are given below. Default is NoneThis option indicates whether a test is in progress Displays the status of the FXO signal bits Indicates the port of the FXO module Interfaces FXO Status TB SIG Interfaces FXO Status PortInterfaces FXO Status TA SIG Interfaces FXO Status RA SIG L2 Protocol TDM Firmware L2 Protocol TDM T1 Protocol FRE L2 Protocol TDM T1 ProtocolL2 Protocol TDM T1 Protocol PPP L2 Protocol TDM T1 Protocol Hdlc L2 Protocol TDM-T1-PPP Config PPP L2 Protocol T1 TDM-T1-PPP ConfigL2 Protocol TDM-T1-PPP Config Mode L2 Protocol TDM-T1-PPP Config PPP MAX Config L2 Protocol TDM-T1-PPP Config PPP Keepalive Period L2 Protocol TDM-T1-PPP Config PPP MAX Timer SECL2 Protocol TDM-T1-PPP Config PPP MAX Failure L2 Protocol TDM-T1-PPP Config PPP Force Peer IP Address L2 Protocol TDM-T1-PPP Status TX Bytes L2 Protocol TDM-T1-FRE ConfigL2 Protocol TDM-T1-PPP Status RX Pkts L2 Protocol TDM-T1-PPP Status RX Bytes L2 Protocol TDM-T1-FRE Config Dlci Mapping NUM L2 Protocol TDM-T1-FRE Config Polling FrequencyL2 Protocol TDM-T1-FRE Config Dlci Mapping L2 Protocol TDM-T1-FRE Config Dlci Mapping Active L2 Protocol TDM-T1-FRE Config Dlci Mapping Mode L2 Protocol TDM-T1-FRE Config Dlci Mapping InterfaceL2 Protocol TDM-T1-FRE Config Dlci Mapping Dlci L2 Protocol TDM-T1-FRE Status L2 Protocol TDM-T1-FRE Status Port Drop Unknown Dlci L2 Protocol TDM-T1-FRE Status Port Current Util %L2 Protocol TDM-T1-FRE Status Port Average Util % L2 Protocol TDM-T1-FRE Status Port Drop Invalid Dlci L2 Protocol TDM-T1-FRE Status Pvcs RX Frames L2 Protocol TDM-T1-FRE Status Pvcs StateL2 Protocol TDM-T1-FRE Status Pvcs TX Frames L2 Protocol TDM-T1-FRE Status Pvcs TX Bytes L2 Protocol TDM-T1-HDLC Status RX Pkts L2 Protocol TDM-T1-HDLC StatusL2 Protocol TDM-T1-HDLC Status TX Pkts L2 Protocol TDM-T1-HDLC Status TX Bytes L2 Protocol TDM-T1-AUTO Status TX Pkts L2 Protocol TDM-T1-AUTO StatusL2 Protocol TDM-T1-AUTO Status State L2 Protocol TDM-T1-AUTO Status RX Pkts L2 Protocol ATM Firmware L2 Protocol ATM-NET-ATM Config ATM Config Idle Cells L2 Protocol ATM-NET-ATM ConfigL2 Protocol ATM-NET-ATM Config ATM Config L2 Protocol ATM NET Protocol L2 Protocol ATM-NET-ATM Config PVC Config NUM L2 Protocol ATM-NET-ATM Config ATM Config HEC CosetL2 Protocol ATM-NET-ATM Config PVC Config L2 Protocol ATM-NET-ATM Config PVC Config Active L2 Protocol ATM-NET-ATM Config PVC Config Setup Router L2 Protocol ATM-NET-ATM Config PVC Config VCIL2 Protocol ATM-NET-ATM Config PVC Config Connection EAP only PPP L2 Protocol ATM-NET-ATM Config PVC Config Setup Connection V35 Setup Setup Connection V35 Setup Setup UNI Dlci L2 Protocol ATM-NET-ATM Config PVC Config Setup VoiceL2 Protocol ATM-NET-ATM Config PVC Config QOS Connection Voice Setup LES-CAS GW SIM L2 Protocol ATM-NET-ATM Status ATM Status Clear Stats L2 Protocol ATM-NET-ATM StatusL2 Protocol ATM-NET-ATM Status ATM Status L2 Protocol ATM-NET-ATM Status PVC Status SUB-INTERFACE L2 Protocol ATM-NET-ATM Status PVC StatusL2 Protocol ATM-NET-ATM Status PVC Status NUM L2 Protocol ATM-NET-ATM Status PVC Status AAL Stats L2 Protocol T1 ATM-T1-ATM Status PVC Status Protocol Status CRC ErrorsRX AAL2 HEC Errors Indicates an EOC cell was received with a voice designation L2 Protocol ATM Firmware Network Interface Cumtn FRE L2 Protocol ATM-NET-CUMTN ConfigClears all recorded statistics and returns all counters to Pots Stats L2 Protocol ATM-NET-CUMTN Config Interface L2 Protocol ATM-NET-CUMTN Config NUML2 Protocol ATM-NET-CUMTN Config Active L2 Protocol ATM-NET-CUMTN Config Dlci L2 Protocol ATM V35 Config UNI Poll Timeout T392 L2 Protocol ATM V35 ConfigL2 Protocol ATM V35 Config UNI Maint Protocol L2 Protocol ATM-NET-CUMTN Status Dlci State L2 Protocol ATM V35 Status Port L2 Protocol V352-ATM Status Pvcs Interfaces ATM DSX Config RX OAM L2 Protocol ATM DSX ConfigInterfaces ATM DSX Config TX OAM Configures the voice parameters for the interface L2 Protocol ALL-ETH-802.3 Status TX Errors L2 Protocol ALL-ETH-802.3 ConfigL2 Protocol ALL-ETH-802.3 Config Mode L2 Protocol ALL-ETH-802.3 Protocol L2 Protocol ALL-ETH-802.3 Status RX Collisions L2 Protocol ALL-ETH-802.3 Status RX ErrorsL2 Protocol ALL-ETH-802.3 Status Crcs L2 Protocol ALL-ETH-802.3 Status NON-ALIGNED View the bridging statistics from this menu Configure the Ethernet Bridging parameters from this menuConfigure the bridge table parameters from this menu View the bridge table status from this menu Router Router Config Interfaces ETH Setup Use this menu to enable RIP on the LAN interfaceRouter Config Interfaces ETH SUB-INTERFACE Only routes not learned from this circuit are advertised Displays the index number in the secondary IP list This is the mask for the network. Default isEnter the secret used by RIP version 2 here This Selection enables IP on this PVC MTU NAT Icmp Doom Server IP address of the public device Private IP address of the active translationPublic IP address of the active translation Type of protocol active on the translation Use this menu to enable RIP on this interface Number of inbound packets using this translationNumber of outbound packets using this translation Napt Address Displays the index number in the static route table Use this menu to set up the Dhcp serverUse this menu to enter static routes to other networks Router Config Dhcp Server Dhcp Address Pools Use this menu to enable the Dhcp server on or OFFRouter Config Dhcp Server Dhcp Server Nbns Server PRI DNS Server PRIDNS Server SEC Nbns Server SEC Router Config UDP Relay Router Config Dhcp Server Exclusion RangesRouter Config Dhcp Server Global Server Options Router Config UDP Relay Mode Network mask applied to the destination address This lists the contents of the unit’s IP route tableNetwork or host destination address Host or router to receive this packet View the IP statistics from this menu IP packets from the units IP stack Packet the unit couldnt route Setting this activator clears the IP StatisticsNumber of IP datagrams successfully reassembled Number of Icmp Time Exceeded messages received Number of Icmp Parameter Problem messages receivedNumber of Icmp Destination Unreachable messages received Number of Icmp Source Quench messages received Number of Icmp Destination Unreachable messages sent Number of Icmp Parameter Problem messages sentNumber of Icmp Address Mask Reply messages received Number of Icmp Time Exceeded messages sent Selecting this activator will clear the Icmp statistics Number of Icmp Address Mask Request messages sentNumber of Icmp Address Mask Reply messages sent View the UDP statistics from this menu View the TCP statistics from this menu Router Status IP Stats TCP Local port of the TCP connection Selecting this activator clears the TCP statisticsLocal IP address of the TCP connection Remote IP address of the TCP connection IP address used for resolving MAC address Ethernet address resolved 0=no resolutionConfigure the filter characteristics from this menu Minutes since entry was first entered into the ARP cache Security Filters Filter Defines MAC Filter Defines Indicates the entry number in the MAC Filter Defines tableSecurity Filters Filter Defines Security Filters Filter Defines IP Filter Defines Indicates the entry number in the IP Filter Defines tableSecurity Filters Filter Defines Pattern Filter Defines 0.0 Security Filters Interfaces SUB-INTERFACE TCP EstabSecurity Filters Interfaces Security Filters Interfaces SET-UP Turns this entry active when set to YES. Default is noSelects the filter define list to reference default is MAC MAC Logically or this filter with the next filter in the list Last filter to combinationLogically and this filter with the next filter in the list Security Radius Server UDP Port Security Radius ServerSecurity Radius Server Server Security Radius Server Secret Security Radius Server Retry Count DS0 Maps Menu DS0 Maps EDIT/VIEW MAP 1 DS0 Displays the network T1 time slot to be assigned DS0 Maps EDIT/VIEW MAP 1 RBS Setting up the Interfaces Appendix A. Configuring the Unit for RoutingInitial Setup T1 Interface Setup Instructions Step Action Layer 2 Protocol FRE Configuration T1 Interface Step Action Configuring the Layer 2 ProtocolEthernet Interface Setup Instructions Layer 2 Protocol FRE Configuration T1 Interface Layer 2 Protocol PPP Configuration T1 Interface Step Action Router Options Ethernet Interface Setting the Router OptionsLayer 2 Protocol Configuration Ethernet Interface For the entry to delete and press the D key Router Options Setting the Default Gateway Step Action Mapping the DS0s 61200624L1-1B ADTRAN, Inc 157 Appendix B. Configuring the Unit for Bridging 61200624L1-1B ADTRAN, Inc 159 160 ADTRAN, Inc DS0 Mapping Instructions Step Action Verifying the Bridge OptionsBridge Options Step Action 162 ADTRAN, Inc Appendix C. Configuring the Unit for Voice Applications Network T1 menus beginning on FXS menus beginning on FXS Interface Setup Instructions Step Action FXS Interface Setup Instructions Appendix D. Configuring the Unit for DSX-1 Applications Network T1 menus beginning on DSX-1 menus beginning on T1 Interface Setup Instructions DSX-1 Interface Setup Instructions Step Action 168 ADTRAN, Inc Application Diagram Appendices T1 ATM Applications 170 ADTRAN, Inc SWITCH, Set D ATA S Crambling appropriately for your network Layer 2 Protocol Configuration T1 InterfaceEnter the I DLE C Ells format for your network Entered by selecting V Oice under the C Onnection field 61200624L1-1B ADTRAN, Inc 173 Appendix B. RFC1483 Quick Start IP Routing 61200624L1-1B ADTRAN, Inc 175 Layer 2 Protocol ATM Configuration T1 Interface ATM-NET-ATM Config PVC Config Setup Router on page 103 for Router Options Ethernet Interface Step Action Router Options T1 Interface L2 Protocol = ATM Step Action Router Options T1 Interface L2 Protocol = ATM Appendix C. RFC1483 Quick Start IP Routing with NAT IP Routing with NAT Appendix D. RFC 1483 Quick Start Bridging PVC Config Setup Router on page 103 for more details Bridge menus beginning on Detail Level Procedures 184 ADTRAN, Inc Introduction DLP-1 Connecting a VT100 Terminal or PC to the Craft PortPrerequisite Procedures Tools and Materials Required Perform the steps below in the order listed DLP-2 Logging in to the System DLP-2 Total Access 600 Series System Manual DLP-3 Setting IP Parameters IP Address Subnet Mask User guest Password password DLP-3 Total Access 600 Series System Manual Access to a PC or other computer connected to the LAN DLP-4 Verifying Communications Over an IP LAN DLP-4 Total Access 600 Series System Manual Total Access 600 Series System Manual DLP-4 194 ADTRAN, Inc DLP-5 Connecting to the Unit Using Telnet DLP-5 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 197 198 ADTRAN, Inc 61200624L1-1B ADTRAN, Inc 199 Enter Have read-only permission for all menu items minimum rights 202 ADTRAN, Inc DLP-7 Updating the Firmware using Tftp DLP-7 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 205 206 ADTRAN, Inc DLP-8 Updating the Firmware using Xmodem Updating Firmware via the Console Menus DLP-9 Saving the Current Configuration Using Tftp DLP-9 Total Access 600 Series System Manual DLP-10 Loading a Configuration Using Tftp DLP-10 Total Access 600 Series System Manual Xmodem Perform the following steps in the order listed DLP-12 Loading a Configuration Using Xmodem DLP-12 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 217 Saving the Total Access 6XX configuration Do not enter further key commands until completing Step Loading a configuration into the Total Access Entering commands at the command prompt 220 ADTRAN, Inc DLP-14 A.03 to A.04 Firmware Upgrade Upgrade From A.03 to A.03.92 Transition Build to A.04 Upgrade From A.03 to A.04 Directly DLP-15 Using the Adtran Utility Syslog Setting up the Total Access 6XX to use Syslog Setting Up the Syslog Host Additional Syslog Features 226 ADTRAN, Inc DLP-16 Executing Terminal Mode Commands Fstimer start x x is in seconds or fstimer stop Example usage ping 10.0.0.5 r 10 si 1500 so eth0 n Example usage trace 10.0.0.5 h 20 t 1 r 1 so eth0 Telnet hostname/address port 230 ADTRAN, Inc DLP-17 Configuring Dual T1 Maps Dual T1 Map Primary T1 Map DSX Map can be mapped to the FXS and FXO access modules only DLP-18 Unit Installation Using the Auto-Config Feature DLP-18 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 237 238 ADTRAN, Inc DLP-19 TDM to ATM Upgrade Purchase the EC/ADPCM P/N 1200613L1 DLP-19 Total Access 600 Series System Manual System Info Firmware Revision field does not display Error 242 ADTRAN, Inc Tftp Server Telnet UtilityVT100 Utility Status Field Meter Field Log Field Telnet Utility Telnet Menu Tree Establishes the Telnet session Session MenuClick on Session to open the Telnet session Connect Capture Menu Edit MenuOptions Menu VT100 Utility Provides online help for using the Adtran UtilitiesHelp Menu Opens the online help Port Menu Opens online help Tftp ServerIdentical to the Telnet Capture Menu see Capture Menu on Server Menu Print Log Meter Field HelpStatus Field LOG Field 252 ADTRAN, Inc Mibs Enterprise MIBs Mibs Supported by TDM UnitsStandard RFC MIBs MIB Compilation Order for TDM Units Traps Supported by TDM Units MIB Variables Supported by TDM Units Mibs Supported by ATM Units Tcp Udp Egp Dsx1 61200624L1-1B ADTRAN, Inc 259 Snmp Atm 61200624L1-1B ADTRAN, Inc 261 262 ADTRAN, Inc