Connection V35 Setup Setup | ADTRAN 624, 612, 616, 606, 604 specs

Section 4 User Interface Guide	Total Access 600 Series System Manual

CONNECTION (V35) > SETUP > SETUP

Use these menus to configure the Protocol mapping, DE map, and FECN map for the V.35 PVC connections.

CONNECTION (V35) > SETUP > SETUP > PROTOCOL MAPPING

Network providers have the ability to provision each PVC pair with an encapsulation mode to ensure interoperability between terminal equipment. The choices are TRANSPARENT or TRANSLATION (def). TRANSLATION mode is most common and carries multiple upper layer protocols over Frame Relay and ATM PVCs.

CONNECTION (V35) > SETUP > SETUP > DE MAP

Maps Frame Relay Discard Eligible (DE) bit to the ATM Cell Loss Priority (CLP) bit. The choices are DE = 0, DE = 1, and CONVERT (map DE TO CLP). The factory default setting is DE = 0.

CONNECTION (V35) > SETUP > SETUP > FECN MAP

Allows mapping of Frame Relay FECN (Forward Explicit Congestion Notification) bit to ATM EFCI (Explicit Forward Congestion Indicator) bit. The choices are NO MAP FECN and MAP FECN. The factory default setting is NO MAP FECN.

CONNECTION (V35) > SETUP > DLCI MAPPING

Use these menus to configure the DLCI mapping for the PVC from the T1 network interface to the V.35 interface.

CONNECTION (V35) > SETUP > DLCI MAPPING > MAP

Displays the DLCI Map number and is used as an index for multiple listings. The first map entry listed is 1, the next is 2, etc. All map numbers assigned will be sequential.

CONNECTION (V35) > SETUP > DLCI MAPPING > ACTIVE

Enables FR/ATM mapping and data passing between the V.35 FRFx connection and the ATM PVC on the network interface. If set to NO, data will not pass from the network to the configured V.35 endpoint. By default, this field is set to YES to allow data to pass as soon as the connection is configured.

CONNECTION (V35) > SETUP > SETUP > INTERFACE

The T1 interface is ATM[0.0] which represents the T1 physical and logical ports respectively. This is an identifier for the system to document the T1 network end of the logical link between the network port and the V.35 interface.

106

© 2004 ADTRAN, Inc.

61200624L1-1B

Image 108

ADTRAN 624, 612, 616, 606, 604 system manual Connection V35 Setup Setup

Contents

Total Access 600 Series Total Access 600R Trademarks To the Holder of the ManualAbout this Manual Revision History ConventionsDocument Revision Date Description of Changes Safety Instructions Save These Important Safety Instructions FCC-Required Information REN/SOC FIC Usoc ADTRAN, Inc Affidavit Requirements for Connection to Digital Services FCC Rules and Regulations Industry Canada Compliance Information Canadian Emissions Requirements Repair and Return Pre-Sales Inquiries and Applications Support Installation and Maintenance Support Post-Sale SupportTraining ADTRAN, Inc Table of Contents Table of Contents Total Access 600 Series System Manual Contents System Description System Overview Features and Benefits Testing Frame Relay SupportAnalog Ports DTE Interface Performance Monitoring IAD Systems Adsl SdslShdsl Equipment Dimensions Power Requirements Reviewing the Front Panel DesignAt-A-Glance Specifications Tables ADTRAN, Inc Equipment Dimensions Power RequirementsReviewing the Front Panel Design Total Access 604/608 Front Panel LEDs TX/RX LinkData Voice Total Access 6XX ATM Front Panel LEDs For these LEDs This color light Indicates that Total Access 612/616/624 Front Panel Layout Total Access 612/616/624 TDM Front Panel LEDs Reviewing the Rear Panel Design Total Access 604/608 Rear Panel Voice Connection Ntwk Connection Craft Port PIN Name Description Description Battery Backup Connection AC Power Connection10/100BaseT Connection Connection Life Line Analog Connection DSX-1 InterfaceProvides the DSX-1 port pinout PIN Description AT-A-GLANCE Specifications Lists the unit specifications Application Feature Specification Analog Ports Routing EthernetManagement Tools Required Unpack and Inspect the System Grounding Instructions Mounting Options This section discusses Total Access 600 Series installation IntroductionTools Required Unpack and Inspect the System Contents of Adtran Shipments Grounding Instructions Wallmount Installation Mounting OptionsWallmounting the Unit Tools Needed Wallmount Orientation Rackmounting the Total Access 612/616/624 Supplying Power to the UnitAC Powered Systems Rackmount Installation User Interface Guide User Interface Guide Total Access 600 Series System Manual Navigating the Terminal Menu Terminal Menu WindowMenu Path Window Panes To do this Press this key Right Window Pane NotationThis notation Means that Additional Terminal Menu Window Features Navigating using the Keyboard KeysMoving through the Menus Configuration Keystrokes Session Management KeystrokesTo do this Getting Help Main Menu and System ControlSelecting the Appropriate Menu DS0 Maps Security Levels Menu DescriptionsMenus Submenus SUB-SUBMENUS System Info Read only Displays the registered Clei code for the unit Read only Displays the current bootcode revision System Config System Config ManagementSystem Config Management Craft Port System Config Management Craft Port Password Protect System Config Management Craft Port Idle Time System Config Management Craft Port Baud RateSystem Config Management Craft Port Data Bits System Config Management Craft Port Parity System Config Management Telnet Access Access System Config Management Telnet Access Authen MethodSystem Config Management Telnet Port System Config Management Telnet Access User List Cannot reset the unit or enter terminal mode System Config Management Telnet Access Active SessionsDisplays the assigned user name Displays the TCP port used for this Telnet session System Config Management Telnet Access IP Access List System Config Management Snmp ManagementSystem Config Management Snmp Management Access System Config Management Snmp Management Trap Delay System Config Management Snmp Management Traps System Config Management FDL Management System Config Management FDL Management Mode System Config Management FDL Management Link IP AddressSystem Config Management FDL Management IP Netmask System Config Management FDL Management FAR-END IP Address System Config Syslog Syslog IP System Config Syslog Syslog FormatSystem Config Syslog Syslog Facility Syslog using Terminal Mode This parameter is for Adtran internal use only System Config Syslog Tollbrg Level System Config Syslog Cmcp LevelSystem Config Syslog Sdsl Level System Config Syslog L1 Level System Config Syslog Pots Level System Config Syslog Lescas LevelSystem Config Syslog ATM Level System Config Syslog Coppercom Level Factory default is GMT-6 Central Minimum required level for sending Filter log messages System Config Network Time Adjust for Daylight Saving System Config Network Time Host AddressSystem Config Network Time Refresh System Config Network Time Status Use this activator to cancel any Tftp transfer in progress Indicates the current status of the update Indicates the status of the previous update View the CPU utilization stats from this menu System Utility System UtilizationSystem Utility System Utilization Performance Activator to start and cancel a ping test Total packets sent read onlyTotal packets received read only Percentage loss based on ping returned from host read only Activates the traceroute process Example usage ping 10.0.0.5 r 10 si 1500 so eth0 n Interfaces T1 Config Interfaces T1 Config Timing ModeInterfaces T1 Config Format Interfaces Displays the T1 performance data Displays current alarms and alarm history for T1 interface Indicates whether a test is in progress Interfaces Shdsl Config NTU/LTU Mode Interfaces Shdsl Config ITU-T/GSPANInterfaces Shdsl Config Radsl AUTO/FIXED Interfaces Shdsl Status NTU/LTU Mode Interfaces Sdsl Config Dslam Interfaces Sdsl Config Dslam SetupConfigure the Dslam settings from this menu Internal Adtran use only Interfaces Sdsl Status Sdsl Rate Interfaces Adsl Status SNR dBInterfaces Network Adsl Interfaces DSX Interfaces DSX Status Performance Current and Totals ES Interfaces DSX Status Performance Current and Totals SESInterfaces DSX Status Performance Current and Totals SEF Interfaces DSX Status Performance Current and Totals FS Interfaces DSX Status Alarms Interfaces DSX Status Alarms Current AlarmsInterfaces DSX Status Alarms Alarm History Interfaces DSX Status Alarms Clear History Configure the various Ethernet parameters from this menu Interfaces ETHDisplays the Ethernet status information Configure the DTE leads from this menu View the status of the DTE leads from this menuThese options are used to loopback tests Interfaces FXS Choices are given below. Default is Loop Start Interfaces FXS Config PortInterfaces FXS Config Mode Indicates the port of the FXS module Interfaces FXS Config SVC Mode Interfaces FXS Config Line ZInterfaces FXS Config MSG IND Interfaces FXS Config Batt Mode Displays the status of the FXS signal bits Displays the port number Choices are given below. Default is None This option indicates whether a test is in progressInterfaces FXO Displays the status of the FXO signal bits Indicates the port of the FXO module Interfaces FXO Status Port Interfaces FXO Status TA SIGInterfaces FXO Status TB SIG Interfaces FXO Status RA SIG L2 Protocol TDM Firmware L2 Protocol TDM T1 Protocol L2 Protocol TDM T1 Protocol PPPL2 Protocol TDM T1 Protocol FRE L2 Protocol TDM T1 Protocol Hdlc L2 Protocol T1 TDM-T1-PPP Config L2 Protocol TDM-T1-PPP Config ModeL2 Protocol TDM-T1-PPP Config PPP L2 Protocol TDM-T1-PPP Config PPP MAX Config L2 Protocol TDM-T1-PPP Config PPP MAX Timer SEC L2 Protocol TDM-T1-PPP Config PPP MAX FailureL2 Protocol TDM-T1-PPP Config PPP Keepalive Period L2 Protocol TDM-T1-PPP Config PPP Force Peer IP Address L2 Protocol TDM-T1-FRE Config L2 Protocol TDM-T1-PPP Status RX PktsL2 Protocol TDM-T1-PPP Status TX Bytes L2 Protocol TDM-T1-PPP Status RX Bytes L2 Protocol TDM-T1-FRE Config Polling Frequency L2 Protocol TDM-T1-FRE Config Dlci MappingL2 Protocol TDM-T1-FRE Config Dlci Mapping NUM L2 Protocol TDM-T1-FRE Config Dlci Mapping Active L2 Protocol TDM-T1-FRE Config Dlci Mapping Interface L2 Protocol TDM-T1-FRE Config Dlci Mapping DlciL2 Protocol TDM-T1-FRE Config Dlci Mapping Mode L2 Protocol TDM-T1-FRE Status L2 Protocol TDM-T1-FRE Status Port Current Util % L2 Protocol TDM-T1-FRE Status Port Average Util %L2 Protocol TDM-T1-FRE Status Port Drop Unknown Dlci L2 Protocol TDM-T1-FRE Status Port Drop Invalid Dlci L2 Protocol TDM-T1-FRE Status Pvcs State L2 Protocol TDM-T1-FRE Status Pvcs TX FramesL2 Protocol TDM-T1-FRE Status Pvcs RX Frames L2 Protocol TDM-T1-FRE Status Pvcs TX Bytes L2 Protocol TDM-T1-HDLC Status L2 Protocol TDM-T1-HDLC Status TX PktsL2 Protocol TDM-T1-HDLC Status RX Pkts L2 Protocol TDM-T1-HDLC Status TX Bytes L2 Protocol TDM-T1-AUTO Status L2 Protocol TDM-T1-AUTO Status StateL2 Protocol TDM-T1-AUTO Status TX Pkts L2 Protocol TDM-T1-AUTO Status RX Pkts L2 Protocol ATM Firmware L2 Protocol ATM-NET-ATM Config L2 Protocol ATM-NET-ATM Config ATM ConfigL2 Protocol ATM-NET-ATM Config ATM Config Idle Cells L2 Protocol ATM NET Protocol L2 Protocol ATM-NET-ATM Config ATM Config HEC Coset L2 Protocol ATM-NET-ATM Config PVC ConfigL2 Protocol ATM-NET-ATM Config PVC Config NUM L2 Protocol ATM-NET-ATM Config PVC Config Active L2 Protocol ATM-NET-ATM Config PVC Config VCI L2 Protocol ATM-NET-ATM Config PVC Config ConnectionL2 Protocol ATM-NET-ATM Config PVC Config Setup Router EAP only PPP L2 Protocol ATM-NET-ATM Config PVC Config Setup Connection V35 Setup Setup L2 Protocol ATM-NET-ATM Config PVC Config Setup Voice L2 Protocol ATM-NET-ATM Config PVC Config QOSConnection V35 Setup Setup UNI Dlci Connection Voice Setup LES-CAS GW SIM L2 Protocol ATM-NET-ATM Status L2 Protocol ATM-NET-ATM Status ATM StatusL2 Protocol ATM-NET-ATM Status ATM Status Clear Stats L2 Protocol ATM-NET-ATM Status PVC Status L2 Protocol ATM-NET-ATM Status PVC Status NUML2 Protocol ATM-NET-ATM Status PVC Status SUB-INTERFACE L2 Protocol ATM-NET-ATM Status PVC Status AAL Stats CRC Errors RX AAL2 HEC ErrorsL2 Protocol T1 ATM-T1-ATM Status PVC Status Protocol Status Indicates an EOC cell was received with a voice designation L2 Protocol ATM-NET-CUMTN Config Clears all recorded statistics and returns all counters toL2 Protocol ATM Firmware Network Interface Cumtn FRE Pots Stats L2 Protocol ATM-NET-CUMTN Config NUM L2 Protocol ATM-NET-CUMTN Config ActiveL2 Protocol ATM-NET-CUMTN Config Interface L2 Protocol ATM-NET-CUMTN Config Dlci L2 Protocol ATM V35 Config L2 Protocol ATM V35 Config UNI Maint ProtocolL2 Protocol ATM V35 Config UNI Poll Timeout T392 L2 Protocol ATM-NET-CUMTN Status Dlci State L2 Protocol ATM V35 Status Port L2 Protocol V352-ATM Status Pvcs L2 Protocol ATM DSX Config Interfaces ATM DSX Config TX OAMInterfaces ATM DSX Config RX OAM Configures the voice parameters for the interface L2 Protocol ALL-ETH-802.3 Config L2 Protocol ALL-ETH-802.3 Config ModeL2 Protocol ALL-ETH-802.3 Status TX Errors L2 Protocol ALL-ETH-802.3 Protocol L2 Protocol ALL-ETH-802.3 Status RX Errors L2 Protocol ALL-ETH-802.3 Status CrcsL2 Protocol ALL-ETH-802.3 Status RX Collisions L2 Protocol ALL-ETH-802.3 Status NON-ALIGNED Configure the Ethernet Bridging parameters from this menu Configure the bridge table parameters from this menuView the bridging statistics from this menu View the bridge table status from this menu Router Use this menu to enable RIP on the LAN interface Router Config Interfaces ETH SUB-INTERFACERouter Config Interfaces ETH Setup Only routes not learned from this circuit are advertised This is the mask for the network. Default is Enter the secret used by RIP version 2 hereDisplays the index number in the secondary IP list This Selection enables IP on this PVC MTU NAT Icmp Doom Private IP address of the active translation Public IP address of the active translationServer IP address of the public device Type of protocol active on the translation Number of inbound packets using this translation Number of outbound packets using this translationUse this menu to enable RIP on this interface Napt Address Use this menu to set up the Dhcp server Use this menu to enter static routes to other networksDisplays the index number in the static route table Use this menu to enable the Dhcp server on or OFF Router Config Dhcp Server Dhcp ServerRouter Config Dhcp Server Dhcp Address Pools DNS Server PRI DNS Server SECNbns Server PRI Nbns Server SEC Router Config Dhcp Server Exclusion Ranges Router Config Dhcp Server Global Server OptionsRouter Config UDP Relay Router Config UDP Relay Mode This lists the contents of the unit’s IP route table Network or host destination addressNetwork mask applied to the destination address Host or router to receive this packet View the IP statistics from this menu IP packets from the units IP stack Setting this activator clears the IP Statistics Number of IP datagrams successfully reassembledPacket the unit couldnt route Number of Icmp Parameter Problem messages received Number of Icmp Destination Unreachable messages receivedNumber of Icmp Time Exceeded messages received Number of Icmp Source Quench messages received Number of Icmp Parameter Problem messages sent Number of Icmp Address Mask Reply messages receivedNumber of Icmp Destination Unreachable messages sent Number of Icmp Time Exceeded messages sent Number of Icmp Address Mask Request messages sent Number of Icmp Address Mask Reply messages sentSelecting this activator will clear the Icmp statistics View the UDP statistics from this menu View the TCP statistics from this menu Router Status IP Stats TCP Selecting this activator clears the TCP statistics Local IP address of the TCP connectionLocal port of the TCP connection Remote IP address of the TCP connection Ethernet address resolved 0=no resolution Configure the filter characteristics from this menuIP address used for resolving MAC address Minutes since entry was first entered into the ARP cache Indicates the entry number in the MAC Filter Defines table Security Filters Filter DefinesSecurity Filters Filter Defines MAC Filter Defines Indicates the entry number in the IP Filter Defines table Security Filters Filter Defines Pattern Filter DefinesSecurity Filters Filter Defines IP Filter Defines 0.0 TCP Estab Security Filters InterfacesSecurity Filters Interfaces SUB-INTERFACE Turns this entry active when set to YES. Default is no Selects the filter define list to reference default is MACSecurity Filters Interfaces SET-UP MAC Last filter to combination Logically and this filter with the next filter in the listLogically or this filter with the next filter in the list Security Radius Server Security Radius Server ServerSecurity Radius Server UDP Port Security Radius Server Secret Security Radius Server Retry Count DS0 Maps Menu DS0 Maps EDIT/VIEW MAP 1 DS0 Displays the network T1 time slot to be assigned DS0 Maps EDIT/VIEW MAP 1 RBS Appendix A. Configuring the Unit for Routing Initial SetupSetting up the Interfaces T1 Interface Setup Instructions Step Action Configuring the Layer 2 Protocol Ethernet Interface Setup InstructionsLayer 2 Protocol FRE Configuration T1 Interface Step Action Layer 2 Protocol FRE Configuration T1 Interface Layer 2 Protocol PPP Configuration T1 Interface Step Action Setting the Router Options Layer 2 Protocol Configuration Ethernet InterfaceRouter Options Ethernet Interface For the entry to delete and press the D key Router Options Setting the Default Gateway Step Action Mapping the DS0s 61200624L1-1B ADTRAN, Inc 157 Appendix B. Configuring the Unit for Bridging 61200624L1-1B ADTRAN, Inc 159 160 ADTRAN, Inc Verifying the Bridge Options Bridge Options Step ActionDS0 Mapping Instructions Step Action 162 ADTRAN, Inc Appendix C. Configuring the Unit for Voice Applications Network T1 menus beginning on FXS menus beginning on FXS Interface Setup Instructions Step Action FXS Interface Setup Instructions Appendix D. Configuring the Unit for DSX-1 Applications Network T1 menus beginning on DSX-1 menus beginning on T1 Interface Setup Instructions DSX-1 Interface Setup Instructions Step Action 168 ADTRAN, Inc Application Diagram Appendices T1 ATM Applications 170 ADTRAN, Inc SWITCH, Layer 2 Protocol Configuration T1 Interface Enter the I DLE C Ells format for your networkSet D ATA S Crambling appropriately for your network Entered by selecting V Oice under the C Onnection field 61200624L1-1B ADTRAN, Inc 173 Appendix B. RFC1483 Quick Start IP Routing 61200624L1-1B ADTRAN, Inc 175 Layer 2 Protocol ATM Configuration T1 Interface ATM-NET-ATM Config PVC Config Setup Router on page 103 for Router Options Ethernet Interface Step Action Router Options T1 Interface L2 Protocol = ATM Step Action Router Options T1 Interface L2 Protocol = ATM Appendix C. RFC1483 Quick Start IP Routing with NAT IP Routing with NAT Appendix D. RFC 1483 Quick Start Bridging PVC Config Setup Router on page 103 for more details Bridge menus beginning on Detail Level Procedures 184 ADTRAN, Inc DLP-1 Connecting a VT100 Terminal or PC to the Craft Port Prerequisite ProceduresIntroduction Tools and Materials Required Perform the steps below in the order listed DLP-2 Logging in to the System DLP-2 Total Access 600 Series System Manual DLP-3 Setting IP Parameters IP Address Subnet Mask User guest Password password DLP-3 Total Access 600 Series System Manual Access to a PC or other computer connected to the LAN DLP-4 Verifying Communications Over an IP LAN DLP-4 Total Access 600 Series System Manual Total Access 600 Series System Manual DLP-4 194 ADTRAN, Inc DLP-5 Connecting to the Unit Using Telnet DLP-5 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 197 198 ADTRAN, Inc 61200624L1-1B ADTRAN, Inc 199 Enter Have read-only permission for all menu items minimum rights 202 ADTRAN, Inc DLP-7 Updating the Firmware using Tftp DLP-7 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 205 206 ADTRAN, Inc DLP-8 Updating the Firmware using Xmodem Updating Firmware via the Console Menus DLP-9 Saving the Current Configuration Using Tftp DLP-9 Total Access 600 Series System Manual DLP-10 Loading a Configuration Using Tftp DLP-10 Total Access 600 Series System Manual Xmodem Perform the following steps in the order listed DLP-12 Loading a Configuration Using Xmodem DLP-12 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 217 Saving the Total Access 6XX configuration Do not enter further key commands until completing Step Loading a configuration into the Total Access Entering commands at the command prompt 220 ADTRAN, Inc DLP-14 A.03 to A.04 Firmware Upgrade Upgrade From A.03 to A.03.92 Transition Build to A.04 Upgrade From A.03 to A.04 Directly DLP-15 Using the Adtran Utility Syslog Setting up the Total Access 6XX to use Syslog Setting Up the Syslog Host Additional Syslog Features 226 ADTRAN, Inc DLP-16 Executing Terminal Mode Commands Fstimer start x x is in seconds or fstimer stop Example usage ping 10.0.0.5 r 10 si 1500 so eth0 n Example usage trace 10.0.0.5 h 20 t 1 r 1 so eth0 Telnet hostname/address port 230 ADTRAN, Inc DLP-17 Configuring Dual T1 Maps Dual T1 Map Primary T1 Map DSX Map can be mapped to the FXS and FXO access modules only DLP-18 Unit Installation Using the Auto-Config Feature DLP-18 Total Access 600 Series System Manual 61200624L1-1B ADTRAN, Inc 237 238 ADTRAN, Inc DLP-19 TDM to ATM Upgrade Purchase the EC/ADPCM P/N 1200613L1 DLP-19 Total Access 600 Series System Manual System Info Firmware Revision field does not display Error 242 ADTRAN, Inc Telnet Utility VT100 UtilityTftp Server Status Field Meter Field Log Field Telnet Utility Telnet Menu Tree Session Menu Click on Session to open the Telnet sessionEstablishes the Telnet session Connect Edit Menu Options MenuCapture Menu Provides online help for using the Adtran Utilities Help MenuVT100 Utility Opens the online help Port Menu Tftp Server Identical to the Telnet Capture Menu see Capture Menu onOpens online help Server Menu Print Log Help Status FieldMeter Field LOG Field 252 ADTRAN, Inc Mibs Mibs Supported by TDM Units Standard RFC MIBsEnterprise MIBs MIB Compilation Order for TDM Units Traps Supported by TDM Units MIB Variables Supported by TDM Units Mibs Supported by ATM Units Tcp Udp Egp Dsx1 61200624L1-1B ADTRAN, Inc 259 Snmp Atm 61200624L1-1B ADTRAN, Inc 261 262 ADTRAN, Inc