Parkside PEXS 270 A1 manual Workplace safety, Electrical safety

Page 7

Introduction / General safety advice for electrical power tools

Sanding plate:

ø 125 mm

Protection class:

 

Noise and vibration data:

Measured values for noise are determined in ac- cordance with EN 60745. The A-weighted noise level of the electrical power tool are typically:

Sound pressure level:

83 dB(A)

Sound power level:

94 dB(A)

Uncertainty K:

3 dB

Wear ear protection!

Vibration total values determined according to EN 60745:

Vibration emission value ah = 5 m / s2, Uncertainty K < 1.5 m / s2.

WARNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vibra- tion levels and in many cases they may exceed the values given in these instructions. It is easy to underes- timate the vibration load if the electrical power tool is used regularly in particular circumstances.

Note: If you wish to make an accurate assessment of the vibration loads experienced during a particular period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actually in use. This can result in a much lower vibration load over the whole of the period of working.

General safety advice for electrical power tools

WARNING! Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury.

Keep all the safety advice and instructions in a safe place for future reference!

The term “electrical tool” used in the safety advice refers to electrical tools powered by mains electrici- ty (by means of a mains lead) and electrical tools powered by rechargeable batteries (without a mains lead).

1. Workplace safety

a)Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents.

b)Do not work with the device

in potentially explosive envi- ronments in which there are

inflammable liquids, gases or dusts. Electrical power tools create sparks, which can ignite dusts or fumes.

c)Keep children and other

people away while you are operating the electrical tool.

Distractions can cause you to lose control of the device.

2. Electrical safety

a)The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock.

b)Avoid touching earthed surfaces such as pipes, radiators, ovens and refrig- erators with any part of your body.

There is an increased risk of electric shock if your body is earthed.

c)Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock.

d)Do not use the mains lead for any purpose for which it was

not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat,

GB/IE

7

Image 7
Contents Random Orbital Sander Pexs 270 A1 GB / IE Page Page Table of contents Intended utilisation Features and FittingsTechnical data IntroductionElectrical safety Workplace safetyPersonal safety General safety advice for electrical power toolsCareful handling and use of electrical power tools Safety advice relating specifically to random orbital sanders Changing sanding sheets Original accessories / toolsSwitching on and off Selecting the Grinding DiscGrinding Surfaces Maintenance and CleaningService centre Warranty Rotary sander is maintenance freeElectrical devices DisposalHans Kompernaß Managing DirectorInhaltsverzeichnis Gebrauch EinleitungAusstattung Lieferumfang BestimmungsgemäßerElektrische Sicherheit Arbeitsplatz-SicherheitZweckentfremden Sie das Kabel nicht, um das Elektro Allgemeine Sicherheitshinweise für ElektrowerkzeugeSicherheit von Personen Verwendung und Behandlung des ElektrowerkzeugsVermeiden Sie eine Überhit Gerätespezifische Sicherheitshinweise für ExzenterschleiferAbtrag und Oberfläche Originalzubehör / -zusatzgeräteSchleifblatt wählen Schleifblatt wechselnFlächen schleifen Vor der Inbetriebnahme / Inbetriebnahme / ArbeitshinweiseStaub- / Späneabsaugung Ein- und ausschaltenGarantie Wartung und Reinigung / Service / Garantie / EntsorgungService Wartung und ReinigungKonformitätserklärung / Hersteller Entsorgung / Konformitätserklärung / HerstellerWerfen Sie Elektrowerkzeuge nicht in den Hausmüll Kompernass Gmbh