Handling Energized Products

General Safety Practices

Do not touch or tamper with the power supply when the power cord is connected. Line voltages may be present inside certain products even when the power switch (if installed) is in the OFF position or a fuse is blown. For DC-powered products, although the voltages levels are usually not hazardous, energy hazards may still exist.

Before working on equipment connected to power lines or telecommunication lines, remove jewelry or any other metallic object that may come into contact with energized parts.

Unless otherwise specified, all products are intended to be grounded during normal use. Grounding is provided by connecting the mains plug to a wall socket with a protective earth terminal. If an earth lug is provided on the product, it should be connected to the protective earth at all times, by a wire with a diameter of 18 AWG or wider. Rack-mounted equipment should be mounted only in earthed racks and cabinets.

Always make the ground connection first and disconnect it last. Do not connect telecommunication cables to ungrounded equipment. Make sure that all other cables are disconnected before disconnecting the ground.

Connection of AC Mains

Make sure that the electrical installation complies with local codes. Always connect the AC plug to a wall socket with a protective ground.

The maximum permissible current capability of the branch distribution circuit that supplies power to the product is 16A. The circuit breaker in the building installation should have high breaking capacity and must operate at short-circuit current exceeding 35A.

Always connect the power cord first to the equipment and then to the wall socket. If a power switch is provided in the equipment, set it to the OFF position. If the power cord cannot be readily disconnected in case of emergency, make sure that a readily accessible circuit breaker or emergency switch is installed in the building installation.

Connection of DC Mains

Unless otherwise specified in the manual, the DC input to the equipment is floating in reference to the ground. Any single pole can be externally grounded.

Due to the high current capability of DC mains systems, care should be taken when connecting the DC supply to avoid short-circuits and fire hazards.

DC units should be installed in a restricted access area, i.e. an area where access is authorized only to qualified service and maintenance personnel.

Make sure that the DC supply is electrically isolated from any AC source and that the installation complies with the local codes.

The maximum permissible current capability of the branch distribution circuit that supplies power to the product is 16A. The circuit breaker in the building installation should have high breaking capacity and must operate at short-circuit current exceeding 35A.

Before connecting the DC supply wires, ensure that power is removed form the DC circuit. Locate the circuit breaker of the panel board that services the equipment and switch it to the OFF position. When connecting the DC supply wires, first connect the ground wire to the corresponding terminal, then the positive pole and last the negative pole. Switch the circuit breaker back to the ON position.

A readily accessible disconnect device that is suitably rated and approved should be incorporated in the building installation.

Page 6
Image 6
RAD Data comm T1, E1 operation manual General Safety Practices, Connection of AC Mains, Connection of DC Mains

T1, E1 specifications

RAD Data Communication specializes in providing advanced networking solutions, particularly for E1 and T1 lines. These digital transmission systems are pivotal in telecommunications, allowing for efficient data transfer, voice communication, and multimedia services.

E1 and T1 lines are standardized digital circuits offering capacity for multiple channels. A T1 line, commonly used in North America, accommodates data transmission at a rate of 1.544 Mbps, while an E1 line, predominantly used in Europe and other parts of the world, supports a rate of 2.048 Mbps. Each line can carry multiple voice channels—up to 24 for T1 and 32 for E1—making them suitable for both voice and data services.

One of the main features of RAD's E1 and T1 solutions is their versatility. These lines can be utilized in various applications, including traditional telephony, private branch exchanges (PBXs), and modern Voice over IP (VoIP) networks. RAD's solutions enable users to seamlessly migrate from older systems to more integrated and efficient digital networks without sacrificing performance.

RAD Data Communication focuses on ensuring reliability and robustness in their E1 and T1 offerings. With built-in error detection mechanisms, such as cyclic redundancy check (CRC), these systems maintain high levels of data integrity. In addition, RAD’s devices often incorporate advanced features like Adaptive Rate Control, allowing for dynamic adjustments to accommodate varying network conditions.

Technology-wise, RAD integrates advanced protocols and features, such as Frame Relay and Multiprotocol Label Switching (MPLS), into their E1 and T1 equipment. This flexibility supports the transmission of diverse data types, ensuring users can transition smoothly between legacy systems and modern technologies.

Another characteristic that sets RAD's products apart is their management capabilities. Many devices come equipped with SNMP (Simple Network Management Protocol) support, enabling remote monitoring and management. This feature is essential for network administrators seeking to maintain optimal performance and quickly address potential issues.

Moreover, RAD's E1 and T1 solutions are designed for easy integration into existing network infrastructures. Their compact and modular design allows for straightforward installation and scalability, accommodating future growth and technology advancements without major overhauls.

In summary, RAD Data Communication’s E1 and T1 solutions are characterized by their reliability, versatility, and advanced management features. Designed to meet the evolving needs of communication networks, they ensure that users can take full advantage of both traditional and modern telecommunications technologies.