Global Machinery Company LS236LS instruction manual Additional safety rules for circular saws

Page 6

Additional safety rules for circular saws

DANGER

a)Keep hands away from cutting area and the blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade.

b)Do not reach underneath the workpiece. The guard cannot protect you from the blade below the workpiece.

c)Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.

d)Never hold piece being cut in your hands or across your leg. Secure the workpiece to a stable platform. It is important to support the work properly to minimize body exposure, blade binding, or loss of control.

e)Hold power tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and shock the operator.

f)When ripping always use a rip fence or straight edge guide. This improves the accuracy of cut and reduces the chance of blade binding.

g)Always use blades with correct size and shape (diamond versus round) of arbour holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.

h)Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially designed for your saw, for optimum performance and safety of operation.

Causes and operator prevention of kickback:

Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator;

When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator;

If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

a)Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces. Position your body to either side of the blade, but not in line with the blade. Kickback could cause the saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions are taken.

b)When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade

is in motion or kickback may occur. Investigate and take corrective actions to eliminate the cause of blade binding.

c)When restarting a saw in the workpiece, centre the saw blade in the kerf and check that saw teeth are not engaged into the material. If saw blade is binding, it may walk up or kickback from the workpiece as the saw is restarted.

d)Support large panels to minimise the risk of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel.

6

Image 6
Contents 2300W 235mm 9-1/4 Circular Saw Contents Dear Customer Description of symbolsSpecifications IntroductionPower tool use and care General safety rulesPersonal safety Work areaAdditional safety rules for laser lights ServiceAdditional safety rules for circular saws Causes and operator prevention of kickbackPage Laser light assembly Laser aperture Trigger switch Know your product12 16 14 21 Adjusting the cutting depth AccessoriesAssembly UnpackingEnsure power is disconnected from the mains socket Adjusting the bevel settingAdjusting the bevel angle Lock the screw with the lock nutMaking a cut Adjusting the angle pointerSwitching on and off Mark the line of cut on the work pieceUsing the parallel fence guide Using the Redeye systemDust extraction Changing the blade Align the beam with the line on the work piecePlace saw on its side on a flat surface Maintenance General inspectionRepairs Save this Manual for future reference