Woodstock M1054 Setup, Unpacking, Box Inventory Figure Qty, Hardware and Tools Not Shown

Page 20

M1048 10" x 18" Metal Cutting Bandsaw

SETUP

Unpacking

The SHOP FOX® Model M1048 has been carefully pack- aged for safe transporting. If you notice the machine has been damaged, please contact your authorized SHOP FOX® dealer immediately.

If any parts are missing, examine the pack- aging for the missing parts. For any missing parts, find the part number in the back of this manual and contact Woodstock International, Inc. at (360) 734-3482 or at tech-support@shopfox.biz

SETUP

Inventory

The following is a description of the main components shipped with the SHOP FOX® Model M1048. Lay the com- ponents out to inventory them.

Note: Some parts and hardware may already be installed on the machine. Make sure to check the machine when you use this inventory list.

Box Inventory (Figure 4)	Qty
A. Model M1048 Metal Cutting Bandsaw	...................1
Hardware and Tools (Not Shown)
—Chip Tray	1
—Triagle Screw 5⁄16-18 x 3⁄4"	1
—Flat Washer 5⁄16	1
—Hex Nut 5⁄16-18	1
—Hex Bolts M12-1.75 x 50 (Leveling)	4
—Hex Nuts M12-1.75 (Leveling)	4
—Handwheel	1
—Knob	1

SUFFOCATION HAZARD!

Immediately discard all

plastic bags and pack-

ing materials to elimi-

nate choking/suffocation hazards for children and animals.

UNPLUG-power cord before you do any assembly or adjustment tasks! Otherwise, serious personal injury to you or others may occur!

Figure 4. Model M1048 inventory.

-10-

Image 20

Contents Model M1054 10 x 18 Metal Cutting Bandsaw Manual Insert Copyright October, 2010 by Woodstock INTERNATIONAL, INCMachine Specifications Cutting Capacities Parts Breakdown Model M1054 Mfg. Since 4/10 Parts List DescriptionSAW BOW XPN03M Bandsaw Page Contents Maintenance Woodstock Technical Support SpecificationsIntroduction Controls and Features Control Panel M1048 control panelSafety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Electrical 220V OperationExtension Cords GroundingSetup UnpackingInventory Box Inventory Figure QtyMachine Placement Cleaning MachineMounting to Shop Floor Bolting to Concrete FloorsTo setup the workstop do these steps Moving & Placing UnitShipping Bracket WorkstopRecommended Adjustments To adjust the feed stop bolt, do these stepsFactory adjustments that should be verified Chip TrayTest Run To test run the bandsaw, do these stepsOperations GeneralVise To rapidly change the vise jaw gap, do these stepsTo adjust the positive stops, do these steps Squaring vise to blade Rear Vise Jaw StopTo adjust the rear blade guide arm Blade Guide ArmsBlade Selection To select the correct blade TPI do these stepsBlade Speed Feed RateTo change blade speeds, do these steps To set the feed rate, do these stepsCoolant System Coolant system reservoir Cover Coolant Control ValveCutting Fluid Biological and PoisonTips for horizontal cutting Bandsaw AccessoriesOperation Tips Maintenance CleaningLubrication Make Sure that your machineTo change the gear oil, do these steps Gear boxService TroubleshootingBandsaw Operations Blade Change To change the blade on the bandsaw, do these stepsTo adjust the blade tracking on the bandsaw, do these steps Blade Tension & TrackingBlade Guide Bearings To adjust the blade guide bearings, do these stepsTo adjust the blade guide roller bearings, do these steps Squaring Blade to Table To square the blade the to the table, do these stepsLimit switch SQ1 Electrical ComponentsModel M1048 220V Wiring Diagram OFFGuides Blade Guides Parts List PART# DescriptionDrive Wheel Parts Breakdown Drive Wheel Parts List Breakdown Main Parts List XPSB30M CAPSCREWM6-1X45 Label Placement Warranty Warranty Registration CommentsBOX BELLINGHAM, WA