Woodstock M1054 owner manual Warranty

Page 52

Warranty

Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from work- manship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred.

Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX® machine or machine part which in normal use has proven to be defective, provided that the original owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair facility designated by our Bellingham, WA office, with proof of their purchase of the product within two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through inspection. If it is determined there is no defect, or that the defect resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost of storing and returning the product.

This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this warranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special or consequential damages arising from the use of our products.

Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durabil- ity standards. We reserve the right to change specifications at any time because of our commitment to continuously improve the quality of our products.

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Model M1054 10 x 18 Metal Cutting Bandsaw Manual Insert Copyright October, 2010 by Woodstock INTERNATIONAL, INCMachine Specifications Cutting Capacities Parts Breakdown Model M1054 Mfg. Since 4/10 Parts List DescriptionSAW BOW XPN03M Bandsaw Page Contents Maintenance Introduction SpecificationsWoodstock Technical Support Controls and Features Control Panel M1048 control panelSafety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety Instructions for Bandsaws Electrical 220V OperationExtension Cords GroundingSetup UnpackingInventory Box Inventory Figure QtyMachine Placement Cleaning MachineMounting to Shop Floor Bolting to Concrete FloorsTo setup the workstop do these steps Moving & Placing UnitShipping Bracket WorkstopRecommended Adjustments To adjust the feed stop bolt, do these stepsFactory adjustments that should be verified Chip TrayTest Run To test run the bandsaw, do these stepsOperations GeneralVise To rapidly change the vise jaw gap, do these stepsTo adjust the positive stops, do these steps Squaring vise to blade Rear Vise Jaw StopTo adjust the rear blade guide arm Blade Guide ArmsBlade Selection To select the correct blade TPI do these stepsBlade Speed Feed RateTo change blade speeds, do these steps To set the feed rate, do these stepsCoolant System Coolant system reservoir Cover Coolant Control ValveCutting Fluid Biological and PoisonOperation Tips Bandsaw AccessoriesTips for horizontal cutting Maintenance CleaningLubrication Make Sure that your machineTo change the gear oil, do these steps Gear boxService TroubleshootingBandsaw Operations Blade Change To change the blade on the bandsaw, do these stepsTo adjust the blade tracking on the bandsaw, do these steps Blade Tension & TrackingTo adjust the blade guide roller bearings, do these steps To adjust the blade guide bearings, do these stepsBlade Guide Bearings Squaring Blade to Table To square the blade the to the table, do these stepsLimit switch SQ1 Electrical ComponentsModel M1048 220V Wiring Diagram OFFGuides Blade Guides Parts List PART# DescriptionDrive Wheel Parts Breakdown Drive Wheel Parts List Breakdown Main Parts List XPSB30M CAPSCREWM6-1X45 Label Placement Warranty Warranty Registration CommentsBOX BELLINGHAM, WA
Top Page Image Contents