Woodstock W1770 To install the resaw fence, do these steps, Enough to slide on the resaw fence

Page 32

4. Tighten the fence lock knob to lock the fence assem- bly in place.

-30-

Installing Resaw Fence

W1770 21" Bandsaw w/Foot Brake

To install the resaw fence, do these steps:		Resaw Lock	Resaw Fence
		Resaw Lock	Resaw Fence
1.	Install the resaw fence lock handle (with the washer	Handle
	and moving plate) onto the fence, then slide the
	resaw fence over the moving plate, as shown in
	Figure 43.
	Note: Leave the moving plate and lock handle loose
	enough to slide on the resaw fence.
2.	Tighten the resaw lock handle.
3.	Loosen the fence lock knob and place the fence		Moving Plate
3.	Loosen the fence lock knob and place the fence
	assembly on the rail, as shown in Figure 44.

Figure 43. Attaching resaw fence to

standard fence.

SETUP

Figure 44. Resaw fence installed.

Image 32

Contents OWNERS MANUAL Page Contents Woodstock Technical Support Functional OverviewMachine Specifications W1770 21 Bandsaw w/Foot Brake Controls and Features Safety Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Use push blocks when necessary Use push sticks whenever possibleExtension Cords Electrical Specifications220V Operation Description Qty Items Needed for SetupUnpacking Hardware and Tools InventoryBox Inventory Figure Qty Machine Placement Cleaning MachineLifting & Moving Lifting the bandsaw 2x4Mounting to Shop Floor Bolting to Concrete FloorsGuide Post Handwheel To install the fence, do these stepsFence Changes in the blade tension may change the blade tracking Blade TrackingTo center track the blade, do these steps Positive Stop To set the positive stop, do these stepsDust Collection To connect the dust collection hoses, do these stepsTest Run To test run the machine, do these stepsResetting the switch To tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings onTensioning Blade Adjusting Blade Guide Bearings To adjust the upper blade guides, do these stepsAdjusting Support Bearings To adjust the upper support bearing, do these stepsBlade aligned 0.016 away from Bearing edge To adjust the lower support bearing, do these steps Lower support bearing controlsAligning Table Cap screws securing table to TrunnionAligning Fence Cap screws securing rail toCalibrating Fence Pointer Calibrating Miter GaugeTo calibrate the pointer, do these steps To calibrate the miter gauge, do these stepsTo install the resaw fence, do these steps Enough to slide on the resaw fenceControl Panel GeneralBasic Controls Front Controls Figure Rear Controls FigureWorkpiece Inspection Cutting wood with minor WarpingBandsaw is capable of performing the following cuts Cutting OverviewBasic Cutting Tips Foot Brake Guide PostFine Tune Tracking Blade LeadCorrecting Blade Lead Aligning Table on Page 27 and Aligning Fence onTo shift the table, do these steps Table Tilt Rip CuttingTo tilt the table, do these steps To make a rip cut, do these stepsCrosscutting ResawingTo make a 90˚ crosscut, do these steps To resaw a workpiece, do these stepsTo complete a stacked cut, do these steps Cutting CurvesStacked Cuts Tooth Style Blade LengthBlade Width Tooth Pitch Blade CareBlade Breakage Most common causes of blade breakage areTo replace a blade, do these steps Blade ChangesTo remove a blade, do these steps Cleaning Table & BaseBrushes LubricationLubricant Frequency Quantity Tension Adjustment AssemblyBlade Guide Rack and Pinion To lubricate the trunnion, do these steps Table Tilt Rack and Pinion AssemblyTrunnion Tools Needed Checking and Tensioning BeltsChecking V-Belts Follow Steps 1-2 in Checking V-Belts on Tensioning V-BeltsReplacing V-Belts Adjusting Tension Lever To adjust the tension lever, do these stepsAdjusting Wheel Blade Brushes To adjust the brushes, do these stepsReplacing Brake Shoe Components and Hardware NeededTo replace the brake shoe Follow Steps 1-4 in Replacing V-Belts onAligning Wheels Checking CoplanarityShimming Upper Wheel GaugeAdjusting Lower Wheel To adjust the lower wheel, do these stepsPower supply terminal box Electrical ComponentsSee Figure Wiring DiagramSee , Troubleshooting Motor & ElectricalMachine Operations Cutting Tips onParts Labels & Cosmetic PartsBlade Guides-Cover Breakdown Guide Post-Table Tilt Breakdown PartsTable-Trunnion Breakdown Body Breakdown Body Parts List Capacitor CoverMotor Cord 12AWG X 3C Resaw Fence Breakdown Warranty Registration CommentsWoodstock international inc. p.o. box Bellingham, wa Warranty