Woodstock W1770 manual Warranty

Page 71

WARRANTY

WARRANTY

Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner.

This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred.

Woodstock International, Inc. will repair or replace, at its expense and at its option, the Shop Fox machine or machine part, which in normal use has proven to be defective, provided that the original owner returns the product prepaid to a Shop Fox factory service center with proof of their purchase of the product within two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through inspection. If it is determined there is no defect, or that the defect resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost of storing and returning the product.

This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant that Shop Fox machinery complies with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this warranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special or consequential damages arising from the use of our products.

Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability standards. We reserve the right to change specifications at any time because of our commitment to continuously improve the quality of our products.

Image 71

Contents OWNERS MANUAL Page Contents Functional Overview Woodstock Technical SupportMachine Specifications W1770 21 Bandsaw w/Foot Brake Controls and Features Safety Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Use push sticks whenever possible Use push blocks when necessaryExtension Cords Electrical Specifications220V Operation Description Qty Items Needed for SetupUnpacking Hardware and Tools InventoryBox Inventory Figure Qty Cleaning Machine Machine PlacementLifting the bandsaw 2x4 Lifting & MovingBolting to Concrete Floors Mounting to Shop FloorGuide Post Handwheel To install the fence, do these stepsFence Changes in the blade tension may change the blade tracking Blade TrackingTo center track the blade, do these steps To set the positive stop, do these steps Positive StopTo connect the dust collection hoses, do these steps Dust CollectionTo test run the machine, do these steps Test RunResetting the switch To tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings onTensioning Blade To adjust the upper blade guides, do these steps Adjusting Blade Guide BearingsTo adjust the upper support bearing, do these steps Adjusting Support BearingsBlade aligned 0.016 away from Bearing edge Lower support bearing controls To adjust the lower support bearing, do these stepsCap screws securing table to Trunnion Aligning TableCap screws securing rail to Aligning FenceTo calibrate the miter gauge, do these steps Calibrating Fence PointerCalibrating Miter Gauge To calibrate the pointer, do these stepsEnough to slide on the resaw fence To install the resaw fence, do these stepsControl Panel GeneralBasic Controls Rear Controls Figure Front Controls FigureCutting wood with minor Warping Workpiece InspectionBandsaw is capable of performing the following cuts Cutting OverviewBasic Cutting Tips Guide Post Foot BrakeAligning Table on Page 27 and Aligning Fence on Fine Tune TrackingBlade Lead Correcting Blade LeadTo shift the table, do these steps To make a rip cut, do these steps Table TiltRip Cutting To tilt the table, do these stepsTo resaw a workpiece, do these steps CrosscuttingResawing To make a 90˚ crosscut, do these stepsTo complete a stacked cut, do these steps Cutting CurvesStacked Cuts Tooth Style Blade LengthBlade Width Most common causes of blade breakage are Tooth PitchBlade Care Blade BreakageTo replace a blade, do these steps Blade ChangesTo remove a blade, do these steps Lubrication CleaningTable & Base BrushesLubricant Frequency Quantity Tension Adjustment AssemblyBlade Guide Rack and Pinion To lubricate the trunnion, do these steps Table Tilt Rack and Pinion AssemblyTrunnion Tools Needed Checking and Tensioning BeltsChecking V-Belts Follow Steps 1-2 in Checking V-Belts on Tensioning V-BeltsReplacing V-Belts To adjust the tension lever, do these steps Adjusting Tension LeverTo adjust the brushes, do these steps Adjusting Wheel Blade BrushesFollow Steps 1-4 in Replacing V-Belts on Replacing Brake ShoeComponents and Hardware Needed To replace the brake shoeChecking Coplanarity Aligning WheelsGauge Shimming Upper WheelTo adjust the lower wheel, do these steps Adjusting Lower WheelElectrical Components Power supply terminal boxSee Figure Wiring DiagramSee , Motor & Electrical TroubleshootingCutting Tips on Machine OperationsLabels & Cosmetic Parts PartsBlade Guides-Cover Breakdown Parts Guide Post-Table Tilt BreakdownTable-Trunnion Breakdown Body Breakdown Capacitor Cover Body Parts ListMotor Cord 12AWG X 3C Resaw Fence Breakdown Comments Warranty RegistrationWoodstock international inc. p.o. box Bellingham, wa Warranty