Woodstock W1770 manual Fence, Guide Post Handwheel, To install the fence, do these steps

Page 18

W1770 21" Bandsaw w/Foot Brake

Fence

The fence rail is installed upside down at the factory.

To install the fence, do these steps:

1.Remove the cap screws holding the rail onto the table, and remove the rail.

2.Flip the rail over and reinstall it with the cap screws removed in Step 1 (see Figure 14).

3.Place the fence on the rail (Figure 15) and tighten it securely with the hand knob. Refer to the instruc- tions on Page 29 to calibrate the pointer.

Figure 14. Tightening guard rail cap

screws.

SETUP

Guide Post Handwheel

Insert the guide post handwheel onto the shaft, and secure it with the cap screw on the flat of the shaft, as shown in Figure 16.

-16-

Figure 15. Installing fence onto rail.

Handle

Figure 16. Guide post handwheel

installed.

Image 18

Contents OWNERS MANUAL Page Contents Woodstock Technical Support Functional OverviewMachine Specifications W1770 21 Bandsaw w/Foot Brake Controls and Features Safety Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Use push blocks when necessary Use push sticks whenever possibleElectrical Specifications 220V OperationExtension Cords Items Needed for Setup UnpackingDescription Qty Inventory Box Inventory Figure QtyHardware and Tools Machine Placement Cleaning MachineLifting & Moving Lifting the bandsaw 2x4Mounting to Shop Floor Bolting to Concrete FloorsTo install the fence, do these steps FenceGuide Post Handwheel Blade Tracking To center track the blade, do these stepsChanges in the blade tension may change the blade tracking Positive Stop To set the positive stop, do these stepsDust Collection To connect the dust collection hoses, do these stepsTest Run To test run the machine, do these stepsResetting the switch Adjusting Blade Guide Bearings on Tensioning BladeTo tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings To adjust the upper blade guides, do these stepsAdjusting Support Bearings To adjust the upper support bearing, do these stepsBlade aligned 0.016 away from Bearing edge To adjust the lower support bearing, do these steps Lower support bearing controlsAligning Table Cap screws securing table to TrunnionAligning Fence Cap screws securing rail toTo calibrate the pointer, do these steps Calibrating Fence PointerCalibrating Miter Gauge To calibrate the miter gauge, do these stepsTo install the resaw fence, do these steps Enough to slide on the resaw fenceGeneral Basic ControlsControl Panel Front Controls Figure Rear Controls FigureWorkpiece Inspection Cutting wood with minor WarpingCutting Overview Basic Cutting TipsBandsaw is capable of performing the following cuts Foot Brake Guide PostCorrecting Blade Lead Fine Tune TrackingBlade Lead Aligning Table on Page 27 and Aligning Fence onTo shift the table, do these steps To tilt the table, do these steps Table TiltRip Cutting To make a rip cut, do these stepsTo make a 90˚ crosscut, do these steps CrosscuttingResawing To resaw a workpiece, do these stepsCutting Curves Stacked CutsTo complete a stacked cut, do these steps Blade Length Blade WidthTooth Style Blade Breakage Tooth PitchBlade Care Most common causes of blade breakage areBlade Changes To remove a blade, do these stepsTo replace a blade, do these steps Brushes CleaningTable & Base LubricationTension Adjustment Assembly Blade Guide Rack and PinionLubricant Frequency Quantity Table Tilt Rack and Pinion Assembly TrunnionTo lubricate the trunnion, do these steps Checking and Tensioning Belts Checking V-BeltsTools Needed Tensioning V-Belts Replacing V-BeltsFollow Steps 1-2 in Checking V-Belts on Adjusting Tension Lever To adjust the tension lever, do these stepsAdjusting Wheel Blade Brushes To adjust the brushes, do these stepsTo replace the brake shoe Replacing Brake ShoeComponents and Hardware Needed Follow Steps 1-4 in Replacing V-Belts onAligning Wheels Checking CoplanarityShimming Upper Wheel GaugeAdjusting Lower Wheel To adjust the lower wheel, do these stepsPower supply terminal box Electrical ComponentsWiring Diagram See ,See Figure Troubleshooting Motor & ElectricalMachine Operations Cutting Tips onParts Labels & Cosmetic PartsBlade Guides-Cover Breakdown Guide Post-Table Tilt Breakdown PartsTable-Trunnion Breakdown Body Breakdown Body Parts List Capacitor CoverMotor Cord 12AWG X 3C Resaw Fence Breakdown Warranty Registration CommentsWoodstock international inc. p.o. box Bellingham, wa Warranty