Woodstock W1770 manual Test Run, To test run the machine, do these steps

Page 22

W1770 21" Bandsaw w/Foot Brake

Test Run

SETUP

Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular opera- tion.

The test run consists of verifying the following: 1) The motor powers up and runs correctly, and 2) the safety disabling mechanism on the switch works correctly, and 3) the OFF button safety feature works correctly.

If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the machine immediately, then review Troubleshooting on Page 57.

If you still cannot remedy a problem, contact our Tech Support at (360) 734-3482 for assistance.

To test run the machine, do these steps:

1.Make sure you understand the safety instructions at the beginning of the manual, and verify that the machine is set up properly.

2.Ensure all tools and objects used during setup are cleared away from the machine.

3.Connect the machine to the power source.

4.Verify that the machine is operating correctly by turning the switch disabling key (Figure 23) to "1" and turning the machine ON.

—When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

—Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems.

5.Press the OFF button to stop the machine.

6.WITHOUT resetting the OFF button, press the ON button. The machine should not start.

—If the machine does not start, the OFF button safety feature is working correctly.

Projectiles thrown from the machine could cause serious eye injury. Wear safety glasses to reduce the risk of injury.

Switch

Disabling

Key

Figure 23. W1770 switch disabling key and

ON/OFF switch

-20-

Image 22

Contents OWNERS MANUAL Page Contents Woodstock Technical Support Functional OverviewMachine Specifications W1770 21 Bandsaw w/Foot Brake Controls and Features Safety Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Bandsaws Use push blocks when necessary Use push sticks whenever possible220V Operation Electrical SpecificationsExtension Cords Unpacking Items Needed for SetupDescription Qty Box Inventory Figure Qty InventoryHardware and Tools Machine Placement Cleaning MachineLifting & Moving Lifting the bandsaw 2x4Mounting to Shop Floor Bolting to Concrete FloorsFence To install the fence, do these stepsGuide Post Handwheel To center track the blade, do these steps Blade TrackingChanges in the blade tension may change the blade tracking Positive Stop To set the positive stop, do these stepsDust Collection To connect the dust collection hoses, do these stepsTest Run To test run the machine, do these stepsResetting the switch Tensioning Blade Adjusting Blade Guide Bearings onTo tension the bandsaw blade, do these steps Adjusting Blade Guide Bearings To adjust the upper blade guides, do these stepsAdjusting Support Bearings To adjust the upper support bearing, do these stepsBlade aligned 0.016 away from Bearing edge To adjust the lower support bearing, do these steps Lower support bearing controlsAligning Table Cap screws securing table to TrunnionAligning Fence Cap screws securing rail toTo calibrate the pointer, do these steps Calibrating Fence PointerCalibrating Miter Gauge To calibrate the miter gauge, do these stepsTo install the resaw fence, do these steps Enough to slide on the resaw fenceBasic Controls GeneralControl Panel Front Controls Figure Rear Controls FigureWorkpiece Inspection Cutting wood with minor WarpingBasic Cutting Tips Cutting OverviewBandsaw is capable of performing the following cuts Foot Brake Guide PostCorrecting Blade Lead Fine Tune TrackingBlade Lead Aligning Table on Page 27 and Aligning Fence onTo shift the table, do these steps To tilt the table, do these steps Table TiltRip Cutting To make a rip cut, do these stepsTo make a 90˚ crosscut, do these steps CrosscuttingResawing To resaw a workpiece, do these stepsStacked Cuts Cutting CurvesTo complete a stacked cut, do these steps Blade Width Blade LengthTooth Style Blade Breakage Tooth PitchBlade Care Most common causes of blade breakage areTo remove a blade, do these steps Blade ChangesTo replace a blade, do these steps Brushes CleaningTable & Base LubricationBlade Guide Rack and Pinion Tension Adjustment AssemblyLubricant Frequency Quantity Trunnion Table Tilt Rack and Pinion AssemblyTo lubricate the trunnion, do these steps Checking V-Belts Checking and Tensioning BeltsTools Needed Replacing V-Belts Tensioning V-BeltsFollow Steps 1-2 in Checking V-Belts on Adjusting Tension Lever To adjust the tension lever, do these stepsAdjusting Wheel Blade Brushes To adjust the brushes, do these stepsTo replace the brake shoe Replacing Brake ShoeComponents and Hardware Needed Follow Steps 1-4 in Replacing V-Belts onAligning Wheels Checking CoplanarityShimming Upper Wheel GaugeAdjusting Lower Wheel To adjust the lower wheel, do these stepsPower supply terminal box Electrical ComponentsSee , Wiring DiagramSee Figure Troubleshooting Motor & ElectricalMachine Operations Cutting Tips onParts Labels & Cosmetic PartsBlade Guides-Cover Breakdown Guide Post-Table Tilt Breakdown PartsTable-Trunnion Breakdown Body Breakdown Body Parts List Capacitor CoverMotor Cord 12AWG X 3C Resaw Fence Breakdown Warranty Registration CommentsWoodstock international inc. p.o. box Bellingham, wa Warranty