|
|
|
|
|
|
|
|
|
| FP2040 | |
|
|
|
|
|
|
|
|
|
| ||
| Troubleshooting Chart |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||
| Symptom | Possible Cause(s) | Corrective Action |
|
| ||||||
| Compressor will not run | 1. | No power or switch in OFF position | 1. | Make sure compressor is plugged in and switch is ON | ||||||
|
|
|
| 2. | Blown fuse | 2. | Disconnect compressor from power source then | ||||
|
|
|
|
|
|
|
| remove pump shroud. Replace fuse (Part. No. | |||
|
|
|
|
|
|
|
| FP200352AV) |
|
| |
|
|
|
| 3. | Motor overheated | 3. | Allow compressor to cool for approximately 30 | ||||
|
|
|
|
|
|
|
| minutes so thermal overload switch will reset. If unit | |||
|
|
|
|
|
|
|
| still does not start, empty air from tank and refer to | |||
|
|
|
|
|
|
|
| actions 1 and 2. |
|
| |
|
|
|
| 4. | Tank pressure at maximum | 4. | Release air from tank | ||||
|
|
|
| 5. | Breaker open | 5. | Reset, determine cause of problem | ||||
|
|
|
| 6. | Pressure switch bad | 6. | Replace pressure switch | ||||
|
|
|
|
|
| ||||||
| Fuses blow/circuit | 1. | Incorrect size fuse, circuit overloaded | 1. | Check for proper fuse in supply circuit. Disconnect | ||||||
| breaker trips repeatedly |
|
|
|
| other electrical appliances from circuit or operate | |||||
|
|
|
|
|
|
|
| compressor on its own branch circuit | |||
|
| ! CAUTION |
| 2. | Defective check valve | 2. | Replace check valve assembly | ||||
| Never use an extension |
|
|
|
|
|
| Do not disassemble check valve. | |||
| cord with this product |
|
|
| ! DANGER |
| With air in tank, bleed tank | ||||
|
|
| first. | ||||||||
|
|
|
|
|
|
|
| ||||
| Thermal overload | 1. | Low voltage | 1. | Eliminate extension cord, check with voltmeter | ||||||
| protector cuts out | 2. | Lack of proper ventilation/room | 2. | Move compressor to well ventilated area | ||||||
| repeatedly |
| temperature too high |
|
|
|
|
|
| ||
|
|
|
| 3. | Check valve malfunction | 3. | Replace check valve assembly | ||||
|
|
|
| 4. | Compressor valves failed | 4. | Replace pump assembly | ||||
|
|
|
|
|
|
|
|
|
| Do not disassemble check valve. | |
|
|
|
|
|
|
| ! DANGER |
| With air in tank, bleed tank | ||
|
|
|
|
|
| first. | |||||
|
|
|
|
|
|
|
| ||||
| Knocks, rattles, | 1. | Loose bolts, tank not level | 1. | Tighten bolts, shim tank to level position | ||||||
| excessive vibration | 2. | Defective bearing on eccentric or | 2. | Replace pump assembly | ||||||
|
|
|
|
| motor shaft |
|
|
|
|
|
|
|
|
|
| 3. | Cylinder or piston ring is worn or | 3. | Replace pump assembly | ||||
|
|
|
|
| scored |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| Tank pressure drops | 1. | Loose drain cock | 1. | Tighten |
|
| ||||
| when compressor shuts | 2. | Check valve leaking | 2. | Replace pump assembly | ||||||
| off | 3. | Loose connections at pressure switch, | 3. | Check all connections with soap and water solution | ||||||
|
|
|
|
| hose or regulator |
|
| and tighten |
|
| |
|
|
|
|
|
|
|
|
|
| Do not disassemble check valve. | |
|
|
|
|
|
|
| ! DANGER |
| With air in tank, bleed tank | ||
|
|
|
|
|
|
|
|
| |||
first.
www.chpower.com
5