RIDGID R8411511 manual Safety Rules for Charger

Page 5

SAFETY RULES FOR CHARGER

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

nBefore using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage.

CAUTION:

To reduce the risk of electric shock or damage to the charger and battery, charge only nickel- cadmium rechargeable batteries as specifically designated on your charger. Other types of batteries may burst, causing personal injury or damage.

nDo not use charger outdoors or expose to wet or damp conditions. Water entering charger will increase the risk of electric shock.

nUse of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

nDo not abuse cord or charger. Never use the cord to carry the charger. Do not pull the charger cord rather than the plug when disconnecting from receptacle. Damage to the cord or charger could occur and create an electric shock hazard. Replace damaged cords immediately.

nMake sure cord is located so that it will not be stepped on, tripped over, come in contact with sharp edges or moving parts or otherwise subjected to damage or stress. This will reduce the risk of accidental falls, which could cause injury, and damage to the cord, which could result in electric shock.

nKeep cord and charger from heat to prevent damage to housing or internal parts.

nDo not let gasoline, oils, petroleum-based products, etc. come in contact with plastic parts. They con-

tain chemicals that can damage, weaken, or destroy plastic.

n An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a.That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25’

50’

100’

Cord Size (AWG)

16

16

16

NOTE: AWG = American Wire Gauge

n Do not operate charger with a damaged cord or plug, which could cause shorting and electric shock. If damaged, have the charger replaced by an authorized serviceman.

nDo not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized serviceman for electrical check to determine if the charger is in good working order.

nDo not disassemble charger. Take it to an authorized serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

nUnplug charger from outlet before attempting any maintenance or cleaning to reduce the risk of electric shock.

nDisconnect charger from the power supply when not in use. This will reduce the risk of electric shock or damage to the charger if metal items should fall into the opening. It also will help prevent damage to the charger during a power surge.

nRisk of electric shock. Do not touch uninsulated portion of output connector or uninsulated battery terminal.

nSave these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also to prevent misuse of the product and possible injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

•lead from lead-based paints,

•crystalline silica from bricks and cement and other masonry products, and

•arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents OPERATOR’S Manual Introduction Table of ContentsElectrical Safety General Safety RulesPersonal Safety Work AreaService Specific Safety RulesSafety Rules for Charger Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Product Specifications FeaturesAssembly Operation LED Function of Charger Power Indicator Evaluate Indicator Charging FullRemoving Battery Pack Installing Battery PackVariable Speed Switch Trigger Variable SpeedTWO-SPEED Gear Train ReversibleTWO Speed Gear Train HI-LO Auxiliary Handle To TightenRemoving Bits Installing BitsAdjustable Torque Clutch Installing Depth Gage RODAdjusting Torque To Increase TorqueDrilling Wood Drilling To Adjust Drilling or Hammer ModeMetal Drilling Masonry DrillingGeneral Maintenance MaintenanceChuck Removal Mallet Chuck Jaws Keyless HEX KEY Wrench ScrewdriverBattery Pack Removal Preparation for Recycling Keeping the Charger Vents CleanDAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredPage Customer Service Information

R8411511 specifications

The RIDGID R8411511 is a powerful and versatile cordless drill driver that stands out in the competitive tool market. Known for its rugged design and exceptional performance, this tool is catered to both professionals and DIY enthusiasts alike. Equipped with a robust 18V lithium-ion battery, the R8411511 ensures maximum run time and efficiency, allowing users to tackle a variety of tasks without the worry of frequent recharging.

One of the standout features of the RIDGID R8411511 is its impressive torque output. The drill delivers an astounding maximum torque of 600 in-lbs, making it capable of handling tough materials such as metal, wood, and even masonry. This high torque setting can effectively tackle heavy-duty applications, making it an invaluable asset for construction sites or home renovations.

The tool features a 2-speed transmission, offering both high-speed (0-1,500 RPM) and high-torque (0-450 RPM) settings. This versatility allows users to easily switch between tasks that require speed for drilling and those that need more power for driving screws. Additionally, the 24-position clutch provides precise control over torque settings, ensuring that each screw is driven to the perfect depth without stripping or damaging the material.

Another key technology found in the R8411511 is the innovative brushless motor. This motor not only increases efficiency but also extends the life of the drill. Brushless motors run cooler than traditional brushed motors, which reduces wear and tear while maximizing battery life. Furthermore, this tool is equipped with an integrated LED light that illuminates workspaces in dim conditions, making it easier to work in tight or poorly lit areas.

The ergonomic design of the RIDGID R8411511 also deserves mention. With a rubberized grip and balanced weight distribution, the drill is comfortable to hold for extended periods, reducing user fatigue. It comes with a 1/2-inch keyless chuck that allows for easy bit changes, adding to its user-friendly nature.

Overall, the RIDGID R8411511 combines power, efficiency, and innovative features, making it an excellent choice for anyone in need of a reliable drill driver. Whether undertaking routine tasks or complex projects, this tool promises consistent performance and durability, solidifying its status as a favorite among tradespeople and hobbyists alike.
Top Page Image Contents