RIDGID R8452 manual Important Safety Instructions, Safety Rules for Charger

Page 6

SAFETY RULES FOR CHARGER

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, battery, and product using battery to prevent misuse of the products and possible injury or damage.

CAUTION:

To reduce the risk of electric shock or damage to the charger and battery, charge only nickel- cadmium rechargeable batteries as specifically designated on your charger. Other types of batteries may burst, causing personal injury or damage.

Do not use charger outdoors or expose to wet or damp conditions. Water entering charger will increase the risk of electric shock.

Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.

Do not abuse cord or charger. Never use the cord to carry the charger. Do not pull the charger cord rather than the plug when disconnecting from receptacle. Damage to the cord or charger could occur and create an electric shock hazard. Replace damaged cords immediately.

Make sure cord is located so that it will not be stepped on, tripped over, come in contact with sharp edges or moving parts or otherwise subjected to damage or stress. This will reduce the risk of accidental falls, which could cause injury, and damage to the cord, which could result in electric shock.

Keep cord and charger from heat to prevent damage to housing or internal parts.

Do not let gasoline, oils, petroleum-based products, etc. come in contact with plastic parts. They contain

chemicals that can damage, weaken, or destroy plastic.

An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure:

a.That pins on plug of extension cord are the same number, size and shape as those of plug on charger.

b.That extension cord is properly wired and in good electrical condition; and

c.That wire size is large enough for AC ampere rating of charger as specified below:

Cord Length (Feet)

25'

50'

100'

Cord Size (AWG)

16

16

16

NOTE: AWG = American Wire Gauge

Do not operate charger with a damaged cord or plug, which could cause shorting and electric shock. If damaged, have the charger replaced by an authorized serviceman.

Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized serviceman for electrical check to determine if the charger is in good working order.

Do not disassemble charger. Take it to an authorized serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

Unplug charger from outlet before attempting any maintenance or cleaning to reduce the risk of electric shock.

Disconnect charger from the power supply when not in use. This will reduce the risk of electric shock or damage to the charger if metal items should fall into the opening. It also will help prevent damage to the charger during a power surge.

Risk of electric shock. Do not touch uninsulated portion of output connector or uninsulated battery terminal.

Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also to prevent misuse of the product and possible injury.

IMPORTANT SAFETY INSTRUCTIONS

1.SAVE THESE INSTRUCTIONS

This manual contains important safety and operating instructions for battery chargers 140276003.

2. Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and product using battery.

3. CAUTION: To reduce the risk of injury, charge only nickel-cadmium rechargeable batteries. Other types of batteries may burst, causing personal injury or damage.

6

Image 6
Contents OPERATOR’S Manual Table of Contents IntroductionPersonal Safety General Safety RulesElectrical Safety Work AreaSpecific Safety Rules ServiceCauses and Operator Prevention of Kickback Additional Safety Rules Important Safety Instructions Safety Rules for ChargerSymbols Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Features Assembly Inner Blade Washer Spindle Lock Button Attaching the BladeRemoving the Blade Spindle Lock Button Loosen HEX KEY TightenOperation Defective Indicator Charging Full Indicator LED Function of ChargerSAW Blades To Install Battery PackTo Remove Battery Pack Blade Guard SystemSee Figures 8 KickbackWrong Kickback Blade SET TOO Deep Incorrect SupportLOCK-OFF Button Switch Trigger Depth Adjustment Knob Depth of CUT AdjustmentTo Adjust Blade Depth STARTING/STOPPING the SAWOperating the SAW Right WrongSee Figures 14 See Figures 16 Using the Edge GuideCross CUTTING/RIP Cutting TOP View of SAWTo Adjust Bevel Setting Bevel CuttingSee Figures 20 To Check To AdjustPositive 0 Bevel Stop Bevel StopPocket Cutting Battery Pack Removal and Preparation for Recycling MaintenanceGeneral Maintenance BatteriesWhat is Covered Under the 3 Year Limited Service Warranty WarrantyDAY Satisfaction Guarantee Policy HOW to Obtain Service What is not CoveredCustomer Service Information