RIDGID R4121 manual Assembly, Unpacking, Mounting Holes, Trace Holes, SAW Base

Page 15

ASSEMBLY

UNPACKING

This product requires assembly.

Carefully lift saw from the carton by the carrying handle and the saw base, and place it on a level work surface. NOTE: This tool is heavy. To avoid back injury, lift with your legs, not your back, and get help when needed.

This saw has been shipped with the saw arm secured in the down position. To release the saw arm, push down on the “D” handle, cut the tie-wrap, and pull out on the lock pin.

Lift the saw arm by the handle. Hand pressure should remain on the “D” handle to prevent sudden rise upon release of the tie wrap.

Inspect the tool carefully to make sure no breakage or damage occurred during shipping.

Do not discard the packing material until you have care- fully inspected and satisfactorily operated the tool.

The saw is factory set for accurate cutting. After assembling it, check for accuracy. If shipping has influenced the settings, refer to specific procedures explained in this manual.

If any parts are damaged or missing, please call 1-866-539-1710 for assistance.

WARNING:

If any parts are damaged or missing, do not oper- ate this tool until the missing parts are replaced. Failure to heed this warning could result in serious personal injury.

WARNING:

Do not attempt to modify this tool or create acces- sories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly is complete. Failure to comply could result in acciden- tal starting and possible serious personal injury.

WARNING:

Do not start the miter saw without checking for interference between the saw blade and the sliding miter fences. Damage could result to the blade if it strikes the miter fence during operation of the saw.

WARNING:

Always make sure the compound miter saw is securely mounted to a workbench or an approved workstand. Failure to heed this warning can result in serious personal injury.

MOUNTING HOLES

See Figure 8.

The compound miter saw should be mounted to a firm supporting surface such as a workbench. Four bolt holes have been provided in the saw base for this purpose. Each of the four mounting holes should be bolted securely us- ing 3/8 in. machine bolts, lock washers, and hex nuts (not included). Bolts should be of sufficient length to accommodate the saw base, lock washers, hex nuts, and the thickness of the workbench. Tighten all four bolts securely.

The hole pattern for mounting to a workbench is shown in figure 8. Carefully check the workbench after mounting to make sure that no movement can occur during use. If any tipping, sliding, or walking is noted, secure the workbench to the floor before operating.

TRACE HOLES

AT THESE LOCATIONS FOR HOLE PATTERN

TRACE HOLES

AT THESE LOCATIONS

FOR HOLE PATTERN

MOUNTING SURFACE

SAW BASE

Fig. 8

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents OPERATOR’S Manual Introduction Table of ContentsGeneral Safety Rules Read ALL Instructions Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Connection Cord Length Wire Size A.W.GElectrical Double InsulationGlossary of Terms Scale FeaturesProduct Specifications MiterBlade Wrench Storage Know Your Compound Miter SAW12 IN. Blade AMP MotorSliding Miter Fences Switch TriggerREPEAT-A-CUT SELF-RETRACTING Lower Blade GuardTools Needed Combination WRENCH, 12 mmPhillips Screwdriver Combination Square Framing Square HEX KEY, 1/16 Installed on ToolLoose Parts Blade Washer Bolt Work Clamp Dust BAG HEX KEYTrace Holes AssemblyUnpacking Mounting HolesDust BAG Installing the Work ClampTo install the work clamp Dust GuideBlade Laser Guide Loosen Tighten Installing the BladeTighten Securely To Prevent Guard Movement BladeCutting a Slot in the Zero Clearance Throat Plate Aligning the Laser Guide LineBroken Line Miter Lock Lever Lift to Unlock Push Down to Lock Adjusting the Miter Lock LeverTo adjust Squaring the SAW Blade to the FenceView of Blade Square with Fence Push Back To Lock Bevel Adjusting the Bevel Lock LeverAdjusting the Bevel Pivot Travel Pivot AdjustmentCorrect View of Blade Squaring the Blade to the Miter TableSee Figures 24 Blade Bevel Lock LeverOperation ApplicationsCutting with Your Compound Miter SAW See Figures 28 To bypass preset index pointsTo Miter CUT / Cross CUT To align with miter scaleBevel Scale Stop PIN Bevel CUT Clamp To Bevel CUTSee Figures 30 Bevel LockCompound Miter CUT To Compound Miter CUTLong Workpiece Supporting Long WorkpiecesClamping Wide Workpieces 45 x 45 Compound Miter CUTMaking AN Auxiliary Fence To attach the auxiliary fence to the sawAuxiliary Fence Cutting Compound Miters COMPOUND-ANGLE Settings for Popular Structures38˚/52˚ 45˚/45˚ Cutting Crown Molding38˚ / 52˚ 45˚/45˚ Angle Miter / Bevel MITER/BEVELLaying Molding Flat on the Miter Table CeilingInside Corner Fence Using a Crown Molding JIG Making a Crown Molding JIGCrown Molding JIG Right Cutting Warped MaterialSee Figures 40 WrongGeneral Maintenance AdjustmentsMaintenance To Adjust the Laser GuideBrush Replacement Proceed as follows when replacement is requiredChanging the Batteries Checking Motor Belt Tension and Replacing the Belt AccessoriesHOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No R4121 Serial No Customer Service Information

R4121 specifications

The RIDGID R4121 is a powerful and versatile table saw that has made a significant impact in the woodworking and construction industries. This innovative tool is designed to meet the needs of both professional contractors and DIY enthusiasts, offering a blend of performance, precision, and portability.

One of the standout features of the R4121 is its robust 15-amp motor, which provides ample power to handle a wide range of cutting tasks. This motor delivers a no-load speed of 5,000 RPM, allowing users to rip through hardwoods, softwoods, and composite materials with ease. The saw's 10-inch blade gives users the ability to make clean, straight cuts, while the adjustable blade height and angle settings enable bevel cuts and varied depths for more complex woodworking projects.

Portability is a key characteristic of the RIDGID R4121. With its compact design and lightweight construction, it can be easily transported to job sites or moved around the workshop. The saw features a sturdy folding stand that can be set up quickly, providing stability while saving valuable space when not in use. This makes it an ideal choice for those who need a dependable table saw that doesn’t sacrifice performance for portability.

In terms of safety, the R4121 is equipped with an array of features designed to protect users during operation. It includes a blade guard for added protection, an anti-kickback pawl for preventing kickbacks, and an emergency stop switch for quick shutdown in case of an unexpected emergency. These safety features enhance user confidence, making it a smart choice for both novice and experienced woodworkers.

The Ridgid R4121 also incorporates advanced technologies to enhance usability and precision. The rack and pinion fence system ensures accurate and consistent cuts, allowing users to make easy adjustments for various workpieces. Additionally, the miter gauge included with the saw provides added versatility for cross-cutting and angled cuts, making it suitable for a diverse array of projects.

Overall, the RIDGID R4121 is a well-rounded table saw that excels in performance, safety, and convenience. Whether you’re tackling home improvement tasks or working on larger construction projects, this tool is designed to deliver reliability and professional-grade results, making it a valuable addition to any workshop. With its combination of power, portability, and precision, the R4121 is poised to become a favorite among users who demand quality and performance in their woodworking tools.
Top Page Image Contents