RIDGID R4121 manual Warranty, DAY Satisfaction Guarantee Policy, Additional Limitations

Page 37

WARRANTY

RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY

Proof of purchase must be presented when requesting war- ranty service.

Limited to RIDGID® hand held and stationary power tools purchased 2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID®, Inc. All warranty communications should be directed to One World Technologies, Inc., attn: RIDGID® Hand Held and Stationary Power Tool Technical Service at (toll free) 1-866-539-1710.

90-DAY SATISFACTION GUARANTEE POLICY

During the first 90 days after the date of purchase, if you are dissatisfied with the performance of this RIDGID® Hand Held and Stationary Power Tool for any reason you may return the tool to the dealer from which it was purchased for a full refund or exchange. To receive a replacement tool you must present proof of purchase and return all original equipment packaged with the original product. The replacement tool will be covered by the limited warranty for the balance of the 3 YEAR service warranty period.

WHAT IS COVERED UNDER THE 3 YEAR LIMITED SERVICE WARRANTY

This warranty on RIDGID® Hand Held and Stationary Power Tools covers all defects in workmanship or materials and nor- mal wear items such as brushes, chucks, motors, switches, cords, gears and even cordless batteries in this RIDGID® tool for three years following the purchase date of the tool. Warranties for other RIDGID® products may vary.

HOW TO OBTAIN SERVICE

To obtain service for this RIDGID® tool you must return it; freight prepaid, or take it in to an authorized service center for RIDGID® branded hand held and stationary power tools. You may obtain the location of the authorized service center nearest you by calling (toll free) 1-866-539-1710 or by log- ging on to the RIDGID® website at www.ridgid.com. When requesting warranty service, you must present the original dated sales receipt. The authorized service center will repair any faulty workmanship, and either repair or replace any part covered under the warranty, at our option, at no charge to you.

WHAT IS NOT COVERED

This warranty applies only to the original purchaser at re- tail and may not be transferred. This warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair by other than an authorized service center for RIDGID® branded hand held and stationary power tools. Consumable accessories provided with the tool such as, but not limited to, blades, bits and sand paper are not covered.

RIDGID®, INC. AND ONE WORLD TECHNOLOGIES, INC. MAKE NO WARRANTIES, REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS POWER TOOLS OTHER THAN THOSE SPECIFICALLY STATED IN THIS WARRANTY.

ADDITIONAL LIMITATIONS

To the extent permitted by applicable law, all implied warran- ties, including warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to three years from the date of purchase. One World Technologies, Inc. and RIDGID®, Inc. are not responsible for direct, indirect, incidental or consequential damages. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

One World Technologies, Inc.

P.O. Box 35, Hwy. 8

Pickens, SC 29671

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents OPERATOR’S Manual Introduction Table of ContentsRead ALL Instructions General Safety Rules Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Cord Length Wire Size A.W.GDouble Insulation Electrical ConnectionGlossary of Terms Product Specifications FeaturesMiter Scale12 IN. Blade Know Your Compound Miter SAWAMP Motor Blade Wrench StorageREPEAT-A-CUT Switch TriggerSELF-RETRACTING Lower Blade Guard Sliding Miter FencesCombination WRENCH, 12 mm Tools NeededPhillips Screwdriver Combination Square Framing Square Loose Parts Installed on ToolBlade Washer Bolt Work Clamp Dust BAG HEX KEY HEX KEY, 1/16Unpacking AssemblyMounting Holes Trace HolesTo install the work clamp Installing the Work ClampDust Guide Dust BAGTighten Securely To Prevent Guard Movement Installing the BladeBlade Blade Laser Guide Loosen TightenAligning the Laser Guide Line Cutting a Slot in the Zero Clearance Throat PlateBroken Line To adjust Adjusting the Miter Lock LeverSquaring the SAW Blade to the Fence Miter Lock Lever Lift to Unlock Push Down to LockView of Blade Square with Fence Adjusting the Bevel Pivot Adjusting the Bevel Lock LeverTravel Pivot Adjustment Push Back To Lock BevelSee Figures 24 Squaring the Blade to the Miter TableBlade Bevel Lock Lever Correct View of BladeApplications OperationCutting with Your Compound Miter SAW To Miter CUT / Cross CUT To bypass preset index pointsTo align with miter scale See Figures 28See Figures 30 To Bevel CUTBevel Lock Bevel Scale Stop PIN Bevel CUT ClampCompound Miter CUT To Compound Miter CUTClamping Wide Workpieces Supporting Long Workpieces45 x 45 Compound Miter CUT Long WorkpieceTo attach the auxiliary fence to the saw Making AN Auxiliary FenceAuxiliary Fence Cutting Compound Miters COMPOUND-ANGLE Settings for Popular Structures38˚ / 52˚ 45˚/45˚ Cutting Crown MoldingAngle Miter / Bevel MITER/BEVEL 38˚/52˚ 45˚/45˚Ceiling Laying Molding Flat on the Miter TableInside Corner Fence Making a Crown Molding JIG Using a Crown Molding JIGCrown Molding JIG See Figures 40 Cutting Warped MaterialWrong Right Maintenance Adjustments To Adjust the Laser Guide General MaintenanceProceed as follows when replacement is required Brush ReplacementChanging the Batteries Checking Motor Belt Tension and Replacing the Belt AccessoriesDAY Satisfaction Guarantee Policy WarrantyWhat is Covered Under the 3 Year Limited Service Warranty HOW to Obtain Service What is not CoveredModel No R4121 Serial No Customer Service Information
Top Page Image Contents