RIDGID R4121 Supporting Long Workpieces, Clamping Wide Workpieces, 45 x 45 Compound Miter CUT

Page 27

OPERATION

SUPPORTING LONG WORKPIECES

See Figures 34 - 35.

Long workpieces need extra supports. Supports should be placed along the workpiece so it does not sag. The support should let the workpiece lay flat on the base of the saw and miter table during the cutting operation. Use the work clamp or a C-clamp to secure the workpiece.

NOTE: When making a compound miter cut as shown in figure 34, it may be necessary to adjust or remove the sliding miter fence to insure proper clearance prior to making the cut.

45° x 45° COMPOUND MITER CUT

Fig. 34

LONG

WORKPIECE

WORKPIECE
SUPPORTS	Fig. 35
	Fig. 35

CLAMPING WIDE WORKPIECES

See Figure 36.

When cutting wide workpieces, such as 2 in. x 10 in., boards should be clamped with a C-clamp.

WIDE BOARD

Fig. 36

Image 27

Contents OPERATOR’S Manual Introduction Table of ContentsGeneral Safety Rules Read ALL Instructions Blade Coasts After Being Turned OFF  Before Making a CUT, be Sure ALL ADJUST- Ments are Secure Specific Safety RulesSpecific Safety Rules Symbol Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Connection Cord Length Wire Size A.W.GElectrical Double InsulationGlossary of Terms Scale FeaturesProduct Specifications MiterBlade Wrench Storage Know Your Compound Miter SAW12 IN. Blade AMP MotorSliding Miter Fences Switch TriggerREPEAT-A-CUT SELF-RETRACTING Lower Blade GuardTools Needed Combination WRENCH, 12 mmPhillips Screwdriver Combination Square Framing Square HEX KEY, 1/16 Installed on ToolLoose Parts Blade Washer Bolt Work Clamp Dust BAG HEX KEYTrace Holes AssemblyUnpacking Mounting HolesDust BAG Installing the Work ClampTo install the work clamp Dust GuideBlade Laser Guide Loosen Tighten Installing the BladeTighten Securely To Prevent Guard Movement BladeCutting a Slot in the Zero Clearance Throat Plate Aligning the Laser Guide LineBroken Line Miter Lock Lever Lift to Unlock Push Down to Lock Adjusting the Miter Lock LeverTo adjust Squaring the SAW Blade to the FenceView of Blade Square with Fence Push Back To Lock Bevel Adjusting the Bevel Lock LeverAdjusting the Bevel Pivot Travel Pivot AdjustmentCorrect View of Blade Squaring the Blade to the Miter TableSee Figures 24 Blade Bevel Lock LeverOperation ApplicationsCutting with Your Compound Miter SAW See Figures 28 To bypass preset index pointsTo Miter CUT / Cross CUT To align with miter scaleBevel Scale Stop PIN Bevel CUT Clamp To Bevel CUTSee Figures 30 Bevel LockCompound Miter CUT To Compound Miter CUTLong Workpiece Supporting Long WorkpiecesClamping Wide Workpieces 45 x 45 Compound Miter CUTMaking AN Auxiliary Fence To attach the auxiliary fence to the sawAuxiliary Fence Cutting Compound Miters COMPOUND-ANGLE Settings for Popular Structures38˚/52˚ 45˚/45˚ Cutting Crown Molding38˚ / 52˚ 45˚/45˚ Angle Miter / Bevel MITER/BEVELLaying Molding Flat on the Miter Table CeilingInside Corner Fence Using a Crown Molding JIG Making a Crown Molding JIGCrown Molding JIG Right Cutting Warped MaterialSee Figures 40 WrongGeneral Maintenance AdjustmentsMaintenance To Adjust the Laser GuideBrush Replacement Proceed as follows when replacement is requiredChanging the Batteries Checking Motor Belt Tension and Replacing the Belt AccessoriesHOW to Obtain Service What is not Covered WarrantyDAY Satisfaction Guarantee Policy What is Covered Under the 3 Year Limited Service WarrantyModel No R4121 Serial No Customer Service Information

R4121 specifications

The RIDGID R4121 is a powerful and versatile table saw that has made a significant impact in the woodworking and construction industries. This innovative tool is designed to meet the needs of both professional contractors and DIY enthusiasts, offering a blend of performance, precision, and portability.

One of the standout features of the R4121 is its robust 15-amp motor, which provides ample power to handle a wide range of cutting tasks. This motor delivers a no-load speed of 5,000 RPM, allowing users to rip through hardwoods, softwoods, and composite materials with ease. The saw's 10-inch blade gives users the ability to make clean, straight cuts, while the adjustable blade height and angle settings enable bevel cuts and varied depths for more complex woodworking projects.

Portability is a key characteristic of the RIDGID R4121. With its compact design and lightweight construction, it can be easily transported to job sites or moved around the workshop. The saw features a sturdy folding stand that can be set up quickly, providing stability while saving valuable space when not in use. This makes it an ideal choice for those who need a dependable table saw that doesn’t sacrifice performance for portability.

In terms of safety, the R4121 is equipped with an array of features designed to protect users during operation. It includes a blade guard for added protection, an anti-kickback pawl for preventing kickbacks, and an emergency stop switch for quick shutdown in case of an unexpected emergency. These safety features enhance user confidence, making it a smart choice for both novice and experienced woodworkers.

The Ridgid R4121 also incorporates advanced technologies to enhance usability and precision. The rack and pinion fence system ensures accurate and consistent cuts, allowing users to make easy adjustments for various workpieces. Additionally, the miter gauge included with the saw provides added versatility for cross-cutting and angled cuts, making it suitable for a diverse array of projects.

Overall, the RIDGID R4121 is a well-rounded table saw that excels in performance, safety, and convenience. Whether you’re tackling home improvement tasks or working on larger construction projects, this tool is designed to deliver reliability and professional-grade results, making it a valuable addition to any workshop. With its combination of power, portability, and precision, the R4121 is poised to become a favorite among users who demand quality and performance in their woodworking tools.