Leica 806648 manual Calibration of tilt sensor Tilt Calibration, After 2 sec, Device, Basic, Mode

Page 15

 

 

Settings

EN

 

 

Calibration of tilt sensor (Tilt Calibration)

1

2

3

4

180°

Place device on absolutely flat surface.

180°

5

6

7

 

Turn the device horizontally by 180°

 

Place device on absolutely flat surface.

 

 

and place it again on absolutely flat

 

 

 

 

 

 

 

surface.

 

 

 

 

 

 

 

After 2 sec

 

 

180°

 

the device

8

9

10

i goes back to

 

 

 

 

 

the basic

 

180°

 

 

mode.

Turn the device horizontally by 180° and place it again on absolutely flat surface.

Leica DISTOTM D810 touch 799093a

14

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Original laser distance meter Leica Distotm D810 touch Leica DistotmTable of Contents Instrument Set-up IntroductionOverview Status bar Main line Function SettingsBasic measuring screen Selection screenCrosshair Zoom with navi- gation keys up and down Pointfinder ViewscreenZoom stage Active function FavoritesCharge batteries when battery symbol is flashing Charging the Li-Ion battery via USBTons can be Using the Touch ScreenOperations TouchUndo last action Switching ON/OFF ClearMultifunctional endpiece Permanent / Minimum-Maximum measuringAreas or volumes Add / SubtractNext meas- urement is added to the previous one Screenshot photo is saved in gallery ScreenshotTilt units SettingsFollowing Switch betweenDistance units Art. No US-Model Art. NoDe-/Activate keylock Switch on with keylock Beep ON/OFFDigital level ON/OFF Bluetooth Settings Basic Calibration of tilt sensor Tilt CalibrationAfter 2 sec DevicePersonalized favorites IlluminationTouch Screen ON/OFF Set time hhmm Compass AdjustmentSet date yyyy-mm-dd Exit settings Date and TimeAn offset adds or subtracts a ResetIzed settings and memories are lost OffsetON/Measure TimerFunctions Starts ifReference Adjusting measuring reference/tripodCalculator If device isTarget surfaces Smart Horizontal ModeMemory Measuring single distanceArea Level32.653 m VolumeOV = Overview PhotoTake photo Exit For screenshots, press camera key for 2 secMeasurement After switching On the device CompassCompass If the device is connected to GalleryFunction is active Long range modeTriangular area Time is increasedLowing point Height-profile measurementAim at reference point REF Aim at additional points DeviceRoof, height of chimneys,… Sloped objectsStops height Height trackingAim laser at lower point Turned on tripodTrapezium area TrapeziumAim laser at upper point Aim laser at 2nd point Use Up/Down navigation keys to show more re- sults 78.383 mAdjust digit Stake outTwo different Horizontal measuring Pythagoras 2-pointResult is shown in the main line MentPythagoras 3-point Aim laser at first target23.018 m 20.571 m Aiming WidthIf necessary, use Zoom for preciseRound object DiameterAim laser perpendicular To the middleLength Area from PhotoSelect arrows with If necessary, use Zoom for precise With softkeys. Corre Aiming ConfirmTilt measurements a transverse tilt should be avoided Technical DataMessage Codes Care WarrantyLimits of use Safety InstructionsAreas of responsibility Prohibited useThis device may not cause interference DisposalElectromagnetic Compatibility EMC FCC statement applicable in U.SNormativa FCC aplicable en EE UU Déclaration FCC, applicable aux Etats-UnisUse of the product with Blue- tooth Laser classificationLabelling
Top Page Image Contents