Leica DISTO D810 manual Calculator, Adjusting measuring reference/tripod, If device is, Reference

Page 20

 

 

Functions

EN

 

 

Calculator

1

2

3

Select key on display.

Confirm every key.

C/CE

=

Use selection keys for

clear or result.

 

 

The measurement result from the main line is taken over to the calcula-

itor and can be used for further calcu- lations.

Ft/in fractions are converted into ft/in decimal.

To takte over a result from the calcu- lator in the basic mode press DIST before leaving the calculator function.

Adjusting measuring reference/tripod

 

 

 

Distance is measured from the rear of the

 

 

 

device (standard setting).

1

2

 

3

 

 

 

Distance is measured from a Leica DISTO

 

 

 

Adapter FTA 360 (lock symbol = perma-

 

 

 

nently)

 

i

If device is

Distance is measured from the tripod

4

switched off,

thread permanently.

 

reference

 

 

 

goes back to

 

 

Confirm setting.

standard set-

 

 

ting (rear of

Distance is measured from the front of the

 

 

 

 

the device).

 

 

device (lock symbol = permanently).

 

 

 

Leica DISTOTM D810 touch 799093a

19

 

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Leica Distotm D810 touch Leica Distotm Original laser distance meterTable of Contents Overview Instrument Set-upIntroduction Function Settings Basic measuring screenSelection screen Status bar Main linePointfinder Viewscreen Zoom stageActive function Favorites Crosshair Zoom with navi- gation keys up and downCharging the Li-Ion battery via USB Charge batteries when battery symbol is flashingUsing the Touch Screen OperationsTouch Tons can beSwitching ON/OFF Clear Multifunctional endpiecePermanent / Minimum-Maximum measuring Undo last actionNext meas- urement is added to the previous one Areas or volumesAdd / Subtract Screenshot Screenshot photo is saved in gallerySettings Tilt unitsSwitch between Distance unitsArt. No US-Model Art. No FollowingDigital level ON/OFF De-/Activate keylock Switch on with keylockBeep ON/OFF Bluetooth Settings Calibration of tilt sensor Tilt Calibration After 2 secDevice BasicTouch Screen ON/OFF Personalized favoritesIllumination Compass Adjustment Set date yyyy-mm-dd Exit settingsDate and Time Set time hhmmReset Ized settings and memories are lostOffset An offset adds or subtracts aTimer FunctionsStarts if ON/MeasureAdjusting measuring reference/tripod CalculatorIf device is ReferenceSmart Horizontal Mode MemoryMeasuring single distance Target surfacesLevel AreaVolume 32.653 mPhoto Take photo ExitFor screenshots, press camera key for 2 sec OV = OverviewCompass Measurement After switching On the deviceCompass Gallery If the device is connected toLong range mode Triangular areaTime is increased Function is activeHeight-profile measurement Aim at reference point REF Aim at additional pointsDevice Lowing pointSloped objects Roof, height of chimneys,…Height tracking Aim laser at lower pointTurned on tripod Stops heightTrapezium Aim laser at upper point Aim laser at 2nd pointUse Up/Down navigation keys to show more re- sults 78.383 m Trapezium areaTwo different Adjust digitStake out Pythagoras 2-point Result is shown in the main lineMent Horizontal measuring23.018 m 20.571 m Pythagoras 3-pointAim laser at first target Width If necessary, useZoom for precise AimingDiameter Aim laser perpendicularTo the middle Round objectArea from Photo Select arrows with If necessary, useZoom for precise With softkeys. Corre Aiming Confirm LengthTechnical Data Tilt measurements a transverse tilt should be avoidedWarranty Message Codes CareSafety Instructions Areas of responsibilityProhibited use Limits of useDisposal Electromagnetic Compatibility EMCFCC statement applicable in U.S This device may not cause interferenceDéclaration FCC, applicable aux Etats-Unis Normativa FCC aplicable en EE UULabelling Use of the product with Blue- toothLaser classification
Top Page Image Contents