Leica 806648, DISTO D810 manual Operations, Using the Touch Screen, Tons can be, Used also

Page 7

Operations

EN

 

 

Using the Touch Screen

Use only fingers to use the touch screen.

Do not allow the touch screen to come into contact with other elec-

itrical devices.

Electrostatic discharges can cause the touch screen to malfunction. Do not allow the touch screen to contact water. The touch screen may malfunction in humid conditions or when exposed to water.

To avoid damaging the touch screen, do not tap it with anything sharp or do not apply excessive pressure to it with your fingertips.

Tapping

Tap on the display to open an on- screen button or to make a selection. Tapping on the icon in the middle of the bottom line activates the distance measurement or triggers the camera.

Dragging

Drag on the display to move to prior or to next screen in the galerie function.

Pinching

Instead of using

i

the touch

screen, the nor-

 

mal keypad but-

 

tons can be

 

used also.

Spread 2 fingers apart to zoom if pointfinder is activated.

Leica DISTOTM D810 touch 799093a

6

 

 

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Original laser distance meter Leica Distotm D810 touch Leica DistotmTable of Contents Introduction Instrument Set-upOverview Status bar Main line Function SettingsBasic measuring screen Selection screenCrosshair Zoom with navi- gation keys up and down Pointfinder ViewscreenZoom stage Active function FavoritesCharge batteries when battery symbol is flashing Charging the Li-Ion battery via USBTons can be Using the Touch ScreenOperations TouchUndo last action Switching ON/OFF ClearMultifunctional endpiece Permanent / Minimum-Maximum measuringAdd / Subtract Areas or volumesNext meas- urement is added to the previous one Screenshot photo is saved in gallery ScreenshotTilt units SettingsFollowing Switch betweenDistance units Art. No US-Model Art. NoBeep ON/OFF De-/Activate keylock Switch on with keylockDigital level ON/OFF Bluetooth Settings Basic Calibration of tilt sensor Tilt CalibrationAfter 2 sec DeviceIllumination Personalized favoritesTouch Screen ON/OFF Set time hhmm Compass AdjustmentSet date yyyy-mm-dd Exit settings Date and TimeAn offset adds or subtracts a ResetIzed settings and memories are lost OffsetON/Measure TimerFunctions Starts ifReference Adjusting measuring reference/tripodCalculator If device isTarget surfaces Smart Horizontal ModeMemory Measuring single distanceArea Level32.653 m VolumeOV = Overview PhotoTake photo Exit For screenshots, press camera key for 2 secCompass Measurement After switching On the deviceCompass If the device is connected to GalleryFunction is active Long range modeTriangular area Time is increasedLowing point Height-profile measurementAim at reference point REF Aim at additional points DeviceRoof, height of chimneys,… Sloped objectsStops height Height trackingAim laser at lower point Turned on tripodTrapezium area TrapeziumAim laser at upper point Aim laser at 2nd point Use Up/Down navigation keys to show more re- sults 78.383 mStake out Adjust digitTwo different Horizontal measuring Pythagoras 2-pointResult is shown in the main line MentAim laser at first target Pythagoras 3-point23.018 m 20.571 m Aiming WidthIf necessary, use Zoom for preciseRound object DiameterAim laser perpendicular To the middleLength Area from PhotoSelect arrows with If necessary, use Zoom for precise With softkeys. Corre Aiming ConfirmTilt measurements a transverse tilt should be avoided Technical DataMessage Codes Care WarrantyLimits of use Safety InstructionsAreas of responsibility Prohibited useThis device may not cause interference DisposalElectromagnetic Compatibility EMC FCC statement applicable in U.SNormativa FCC aplicable en EE UU Déclaration FCC, applicable aux Etats-UnisLaser classification Use of the product with Blue- toothLabelling
Top Page Image Contents