Husky D28752 manual Before Each Start-Up, How to Start

Page 13

Before Each Start-Up:

1.Place On/Auto/Off lever to “OFF” and close air regulator.

2.Pull regulator knob out, turn counter-clockwise until it stops. Push knob in to lock in place.

3.Attach hose and accessories. NOTE: The hose or accessory will require a quick connect plug if the air outlet is equipped with a quick connect socket.

Too much air pressure causes a hazardous risk of bursting. Check the manufacturer’s maximum pressure rating for air

tools and accessories. The regulator outlet pressure must never exceed the maximum pressure rating.

How to Start:

1.Turn the On/Auto/Off lever to “AUTO” and allow tank pressure to build. Motor will stop when tank pressure reaches “cut-out” pressure.

2.Pull the regulator knob out and turn clockwise to increase pressure. When the desired pressure is reached push knob in to lock in place. The compressor is ready for use.

NOTE: Always operate the air compressor in well-ventilated areas free of gasoline or other combustible vapors. If the compressor is being used to operate a sprayer DO NOT place near the spray area.

13- ENG

D28752

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Air Compressor Operator’s Manual Important Safety Instructions Safety Guidelines DefinitionsOr serious injury Minor or moderate injury Death or serious injuryExplosion May be required Spray area. An additional length of hoseLocation away from compressor Fire, do not allow the compressor toWhat Could Happen Attachments & AccessoriesElectricity. Like any other electrically Safety equipment must be properlyRepairs attempted by unqualified Air to all applicable local and federalResult in serious burns Or attempt maintenance until unit hasHot for several minutes after operation Do not reach around protective shroudsFire, Inhalation, Damage to Vehicle Surfaces Glossary SpecificationsDuty Cycle Model No Y6010Location of the Air Compressor InstallationPlug Grounding Pin Grounded Outlets Voltage and Circuit Protection Extension CordsKnow Your Air Compressor OperationDescription of Operation Before Starting How to StopCooling System not shown This compressor Check ValveBefore Each Start-Up How to StartTo Check Safety Valve MaintenanceCustomer Responsibilities To Drain TankTo Replace or Clean Check Valve Service and AdjustmentsStorage Troubleshooting Pressure reading Problem Cause Correction Husky Air Compressor warranted by Dapc Limited WarrantyMuerte o lesiones serias Definiciones DE Normas DE SeguridadModeradas Lesiones serias Causar daños en la propiedadCómo prevenirlo Instrucciones Importantes DE SeguridadQué puede occurrir Cómo prevenirlo Advertencia Riesgo de ExplosiónNunca opere el compresor sin sus defensas o Advertencia Riesgo de Caída Qué puede occurrir Advertencia Riesgo de Quemaduras Qué puede occurrirAdvertencia Riesgo de Operación Lasegura Qué puede occurrir Ciclo DE Servicio GlosarioUbicación del compresor de aire InstalaciónProtección del voltaje y del circuito Cables de extensión eléctricaConozca su compresor de aire OperaciónDescripción de operaciones Cómo detenerla Cómo utilizar su unidadAntes de poner en marcha Válvula reguladoraCómo poner en marcha Antes de cada puesta en marchaResponsabilidades del cliente MantenimientoCómo verificar la válvula de seguridad Cómo drenar el tanquePara reemplazar o limpiar la válvula reguladora Servicio Y AjustesAire, originando un riesgo de ruptura de sus paredes AlmacenajeSobre la soldadura o cosa Guía DE Diagnóstico DE ProblemasAire, ello lo debilitará. El Tanque podría romperse oDesciende cuando El motor no funciona El compresor de aire Husky está garantizado por Dapc Garantía LimitadaConsignes DE Sécurité Importantes Mesures DE Sécurité DéfinitionsOu la mort Causer des blessures mineures ou Moyennes Évité, peut causer des dommages à laAvertissement Risque dexplosion ou dincendie Prévention Conserver ces directivesRisque Prévention Avertissement Risque déclatementAvertissement Risque de projection dobjets Avertissement Risque par inhalation Avertissement Risque de choc électriqueAvertissement Risque relié aux pièces mobiles Avertissement Risque de brûluresAvertissement Risque de chute Avertissement Risque dune utilisation dangereuse RisqueLexique Cycle DE ServiceSpécifications Ce compresseurs peut fonctionner sur un circuit deFiche Emplacement du compresseur dairPrises de courant mises à la terre Protection contre la surtension et protection du circuit RallongesFamiliarisez-vous avec votre compresseur dair UtilisationDescription du fonctionnement Soupape Connexion rapideArrêt de lappareil Utilisation de lappareilAvant le démarrage Mise en marche Avant chaque mise en marcheResponsabilités du client EntretienVérification de la soupape de sûreté Vidange du réservoirEntretien ET Réglages Remplacement ou nettoyage de la soupape de retenueTube de sortie Écrou Soupape de retenue Tournevis En position fermée, le disque est visibleRangement Peut éclater ou exploser SerrerConsidérée normale Fusible sauté ou coupe-circuit D28752 58- FR 59- FR D28752 Le compresseur dair Husky est garanti par Dapc Garantie Limitée

D28752 specifications

Husky D28752 is a cutting-edge machine, renowned for its advanced design and robust functionality in the field of industrial automation. This model exemplifies Husky's commitment to innovation, catering to diverse industries such as packaging, automotive, and consumer goods.

A standout feature of the Husky D28752 is its exceptional speed. It is engineered to optimize production lines, achieving high output rates without compromising on quality. This efficiency is largely attributed to its state-of-the-art injection molding technology, which allows for precise control over the molding process, resulting in reduced cycle times.

The D28752 incorporates advanced automation technologies, enhancing its operational capabilities. With integrated robotics, the machine can perform complex tasks with minimal human intervention. This not only increases productivity but also reduces labor costs and the potential for errors. The automation is complemented by an intuitive user interface, designed for operators to easily monitor and adjust settings in real-time.

Reliability is another hallmark of the D28752. Built with durable materials, the machine is designed to withstand the rigors of continuous operation. Its robust construction minimizes the likelihood of breakdowns, ensuring that production schedules remain on track. Additionally, the D28752 features predictive maintenance capabilities, utilizing data analytics to anticipate potential issues before they arise.

The machine is also highly versatile, accommodating various molds and materials. This flexibility makes it an ideal choice for companies looking to diversify their product offerings without investing in multiple machines. The D28752 supports a range of thermoplastics and is compatible with both standard and custom molds, allowing for significant customization in production.

Energy efficiency is a core principle in the design of the Husky D28752. Its engineering minimizes energy consumption, leading to both cost savings and a reduced environmental footprint. By incorporating energy-saving technologies, the machine meets the increasing demand for sustainable manufacturing practices.

In summary, Husky D28752 stands out as a machine that combines speed, reliability, and versatility with cutting-edge technology. Designed with the future of manufacturing in mind, it addresses the key challenges faced by modern industries, making it a valuable asset for companies striving for excellence in production.
Top Page Image Contents