Husky D28752 manual Service and Adjustments, To Replace or Clean Check Valve

Page 15

SERVICE AND ADJUSTMENTS

Unit cycles automatically when power is on. When doing Maintenance, you may be exposed to voltage sources,

compressed air or moving parts. Personal injuries can occur. Before performing any Maintenance or repair, unplug the compressor and bleed off all air pressure.

ALL MAINTENANCE AND REPAIR OPERATIONS NOT LISTED MUST BE PERFORMED BY TRAINED SERVICE TECHNICIAN.

To Replace or Clean Check Valve

1.Release all air pressure from air tank. See “To Drain Tank” in the Maintenance section.

2.Unplug outfit.

3.Loosen the nut on the outlet tube and move the outlet tube to the side.

4.Unscrew the check valve (turn counterclockwise) using a socket wrench.

5.Make sure the valve disc moves freely inside the check valve and the spring holds the disc in the upper, closed position. The check valve may be cleaned with a solvent, such as paint and varnish remover.

6.Apply sealant to the check valve threads. Reinstall the check valve (turn clockwise).

7.Replace the outlet tube and tighten the nut.

8.Perform the Break-in Procedure. See “Break-in Procedure” in the Operation section.

Outlet Tube

Nut

Check

Valve

Screwdriver

In open position nothing is visible.

In closed position disc is visible.

15- ENG

D28752

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Air Compressor Operator’s Manual Death or serious injury Safety Guidelines DefinitionsImportant Safety Instructions Or serious injury Minor or moderate injuryFire, do not allow the compressor to Spray area. An additional length of hoseExplosion May be required Location away from compressorWhat Could Happen Attachments & AccessoriesAir to all applicable local and federal Safety equipment must be properlyElectricity. Like any other electrically Repairs attempted by unqualifiedDo not reach around protective shrouds Or attempt maintenance until unit hasResult in serious burns Hot for several minutes after operationFire, Inhalation, Damage to Vehicle Surfaces Model No Y6010 SpecificationsGlossary Duty CycleInstallation Location of the Air CompressorPlug Grounding Pin Grounded Outlets Voltage and Circuit Protection Extension CordsOperation Know Your Air CompressorDescription of Operation Check Valve How to StopBefore Starting Cooling System not shown This compressorBefore Each Start-Up How to StartTo Drain Tank MaintenanceTo Check Safety Valve Customer ResponsibilitiesTo Replace or Clean Check Valve Service and AdjustmentsStorage Troubleshooting Pressure reading Problem Cause Correction Husky Air Compressor warranted by Dapc Limited WarrantyLesiones serias Causar daños en la propiedad Definiciones DE Normas DE SeguridadMuerte o lesiones serias ModeradasCómo prevenirlo Instrucciones Importantes DE SeguridadQué puede occurrir Cómo prevenirlo Advertencia Riesgo de ExplosiónNunca opere el compresor sin sus defensas o Advertencia Riesgo de Caída Qué puede occurrir Advertencia Riesgo de Quemaduras Qué puede occurrirAdvertencia Riesgo de Operación Lasegura Qué puede occurrir Ciclo DE Servicio GlosarioUbicación del compresor de aire InstalaciónProtección del voltaje y del circuito Cables de extensión eléctricaOperación Conozca su compresor de aireDescripción de operaciones Válvula reguladora Cómo utilizar su unidadCómo detenerla Antes de poner en marchaCómo poner en marcha Antes de cada puesta en marchaCómo drenar el tanque MantenimientoResponsabilidades del cliente Cómo verificar la válvula de seguridadPara reemplazar o limpiar la válvula reguladora Servicio Y AjustesAire, originando un riesgo de ruptura de sus paredes AlmacenajeTanque podría romperse o Guía DE Diagnóstico DE ProblemasSobre la soldadura o cosa Aire, ello lo debilitará. ElDesciende cuando El motor no funciona El compresor de aire Husky está garantizado por Dapc Garantía LimitadaÉvité, peut causer des dommages à la Mesures DE Sécurité DéfinitionsConsignes DE Sécurité Importantes Ou la mort Causer des blessures mineures ou MoyennesAvertissement Risque dexplosion ou dincendie Prévention Conserver ces directivesAvertissement Risque déclatement Risque PréventionAvertissement Risque de projection dobjets Avertissement Risque par inhalation Avertissement Risque de choc électriqueAvertissement Risque de brûlures Avertissement Risque relié aux pièces mobilesAvertissement Risque de chute Avertissement Risque dune utilisation dangereuse RisqueCe compresseurs peut fonctionner sur un circuit de Cycle DE ServiceLexique SpécificationsEmplacement du compresseur dair FichePrises de courant mises à la terre Protection contre la surtension et protection du circuit RallongesSoupape Connexion rapide UtilisationFamiliarisez-vous avec votre compresseur dair Description du fonctionnementUtilisation de lappareil Arrêt de lappareilAvant le démarrage Mise en marche Avant chaque mise en marcheVidange du réservoir EntretienResponsabilités du client Vérification de la soupape de sûretéEn position fermée, le disque est visible Remplacement ou nettoyage de la soupape de retenueEntretien ET Réglages Tube de sortie Écrou Soupape de retenue TournevisRangement Peut éclater ou exploser SerrerConsidérée normale Fusible sauté ou coupe-circuit D28752 58- FR 59- FR D28752 Le compresseur dair Husky est garanti par Dapc Garantie Limitée

D28752 specifications

Husky D28752 is a cutting-edge machine, renowned for its advanced design and robust functionality in the field of industrial automation. This model exemplifies Husky's commitment to innovation, catering to diverse industries such as packaging, automotive, and consumer goods.

A standout feature of the Husky D28752 is its exceptional speed. It is engineered to optimize production lines, achieving high output rates without compromising on quality. This efficiency is largely attributed to its state-of-the-art injection molding technology, which allows for precise control over the molding process, resulting in reduced cycle times.

The D28752 incorporates advanced automation technologies, enhancing its operational capabilities. With integrated robotics, the machine can perform complex tasks with minimal human intervention. This not only increases productivity but also reduces labor costs and the potential for errors. The automation is complemented by an intuitive user interface, designed for operators to easily monitor and adjust settings in real-time.

Reliability is another hallmark of the D28752. Built with durable materials, the machine is designed to withstand the rigors of continuous operation. Its robust construction minimizes the likelihood of breakdowns, ensuring that production schedules remain on track. Additionally, the D28752 features predictive maintenance capabilities, utilizing data analytics to anticipate potential issues before they arise.

The machine is also highly versatile, accommodating various molds and materials. This flexibility makes it an ideal choice for companies looking to diversify their product offerings without investing in multiple machines. The D28752 supports a range of thermoplastics and is compatible with both standard and custom molds, allowing for significant customization in production.

Energy efficiency is a core principle in the design of the Husky D28752. Its engineering minimizes energy consumption, leading to both cost savings and a reduced environmental footprint. By incorporating energy-saving technologies, the machine meets the increasing demand for sustainable manufacturing practices.

In summary, Husky D28752 stands out as a machine that combines speed, reliability, and versatility with cutting-edge technology. Designed with the future of manufacturing in mind, it addresses the key challenges faced by modern industries, making it a valuable asset for companies striving for excellence in production.
Top Page Image Contents