Sears 113.244501 manual AssernbBy, Mounting Band SAW to Workbench

Page 7

ITEM

=

A

B

C

D

C

TABLE OF LOOSE PARTS	QTY.
Basic saw assembly	1
Owners Manual	1
Saw Table	t
Loose Parts Bag
Containing the following parts:
Key Switch	1
Wing Nut t/4-20 x 5/8	1
Screw, Truss Hdo 1/4-20	1
Wrench, Hex "L" 1/8	1
Bevel Indicator	1
Screw, Pan Cross 10-32 x 3/8	1
Washer 17/64 x 1 x 1/16	1
Bolt, Carriage I/4-20 x 1	1
Knob	1
Clip Hose	1

assernbBy

MOUNTING BAND SAW TO WORKBENCH

If band saw is to be used in a permanent location, it should be fastened securely to a firm supporting sur- face such as a workbench

If mounting to a workbench, holes should be drilled through supporting surface of the workbench using dimensions illustrated,

1 Each leg should be bolted securely using 5/16" diameter machine screws, Iockwashers, and 5/16"

hex nuts (not included)Screw length should be 1-3/4" plus the thickness of the bench top,

2Locate and mark the holes where band saw is to be mounted

3 Drill (4) 3/8" diameter holes through workbench,,

4, Place band saw on workbench aligning holes in feet with holes drilled in workbench

5 Insert all four 5/16" screws and tighten,

i

i

i ii 1,1,,

, ii ,,11,i,l,ll,llr

NOTE: All bolts should be inserted from the top tnstall the washers and nuts from the underside of the

bench

	3/8" DIAMETER
5"'	(4) HOLES

CLAMPING BANDSAW TO WORKBENCH

The Band Saw can be clamped directly to a work-

bench LJsingtwo (2) or more "C" clamps on base of unit

"C" Clamp

Workbench

Image 7

Contents For Future Reference Model NO, 113,244501For Band Saw Safety InstructionsBefore Using the SAW When Installing or Moving the SAWTo avoid injury from jams, slips or thrown pieces USE only Recommended AccessoriesInspect your workpiece For woodworking Gnossaty of termsConnecting to Power Supply Outlet Motor specifications and eRectrBcanrequBrementsFeet No.. t6 ALONO1.,S Mounting Band SAW to Workbench AssernbByAssembOy Installing the TableLowerBack-UpBearing Installing the BladeTension Aot..,,ngCarefully uncoil the blade holding it at arms length TensionWheelUnplug before making any adjustments Adjusting the Blade Guides and BACK-UP BearingTracking the Blade Loosen the upper slide lock knob and position Final Table AssemblyAligning the Table Square To the Blade Pen. Thrown blades can cause injuryDlc o Installing the Hose ClipFrame Getting to know your band sawTilt bevel scale Shows degree table is t/Ited Iiiii Plan your work Dress for safetyBasic Saw Operations Check for Damaged PARTS. Check forBefore Leaving the SAW Whenever SAW iS RunningWorkplece KerrPatternLine Sears recommends the following accessories MaintenanceCo,a ,lo,t Band Saw slows down when cutting Blades breaking= TroubleshootingBearings are in contact with the blade Scr Pan HD TY TT Repair partsGuard Blade Scr Truss 1/4-20 x 5/8Always order by Part Number- Not by Key Number For 10-INCH Band SAWSee Figure Key Part Pad Description Always order by Part Number- Not by Key Number820272 =800=827=6655 For the repair or replacement parts you needFor in-homemajor brand repair service =800=4=REPAIR