Sears 113.19771 owner manual OHPtArED O

Page 14

Loosen (2) V4 20 Gib set screws on the left side at the rear of the column support,

3.Elevate, and then lower the Arm: (a) if the column

binds and elevation is difficult loosen two 5/16 - 18 plated bolts on front side of the column support until

you achieve smooth but firm elevation. (b) If the column moves side-to-side within the column support, tighten the two 5/16 -- 18 plated bolts until movement disappears - elevation should be smooth and firm.

4.Now tighten the (2) Yf, 20 Gib set screws until no

noticeable rotational play exists between Column Tube and Column Support.

5.Recheck elevation and re-adjust if necessary.

6, Replace Column Support trim.

B ,OHPtArED O

BLADE

ROTATION 1

STEP THREE

SQUARING CROSS CUT TRAVEL (CARRIAGE

TRAVELS IN A STRAIGHT LINE).

1.Index but do not lock arm at 0 ° miter.

2.Install saw blade as shown. Motor shaft has left hand threads.

NOTE: Do not overtightenarbor nut. Use the arbor wrench to just "snug" it.

SHAFT WRENCH

o END OF ARBOR WRENCH Rf_STING ON TABLE

SAW BLADE

_..__

 

 

 

OCTEF_ COLLAR

__

iii

_._

MOTOR

ARBOR NUT

_INNER

 

 

COLLAR

14

Image 14
Contents Sears SAW onlyUSE Recommended Accessories Full ONE Year Warranty on Craftsman Radial SAWKnow Your Power Tool Ground ALL ToolsInstal Lation Additional safety instructionsFor radial saws Minimize Accident PotentialReposition Antikickback With PowerRipping PloughingElectrical connections Power SupplyMotor Specifications SawConnections should be Made by a Motor Safety ProtectionElectrical Connections Qualified ElectricianWire Sizes Locations and Functions of ControlsContents ToolsLenkwasher, 5/16 External Containing the following ItemsTruss Hd /4-20 Lockwasher, 1/4 Nut Hex Jam 5/16-18 Nat, Hex 1/2-13Elevate ARM to ITS Maximum Height STIFFENER1Attach Elevation Crank Remove Shipping Screws and Discard Assembly and alignmentLock ARM Before Proceeding Collar, Set aside and out of the wayAttaching and Leveling Table Mounting Support Channels Alignment ProcedureStep ONE Arbor Wrench Screw aStep TWO Installation of Front Work TableAdjusting Column Tube in Column Support OHPtArED O HEX WrenchStep Five Squaring Blade to RIP Guide Fence Blade Heel AdjustmentStep Four Squaring SAW Blade to Work TableRest Vertical Heel AdjustmentTooth Table Spacer Board Installingand Adjusting RIP Scale IndicatorsStep SIX KnobInstall Blade Guard Fence LocationsTable Clamp Controls Power Switch and KeyLocations and functions Unlock Index R,ELEASEAntikickback Pencil Line for Gauging Required Length Basic saw operationsThis Edge of Board Against Fence for ALL Cutsfence 1ST CUT Repetitive Crosscutting Requirements for CrosscutOperation No Crosscut Operations 1 ThroughOperation No -- Compound Operation No Miter CrosscutOperation No Bevel Crosscut CrosscutIN-RIPPING Requirements When RippingOperation No -- OUT-RIPPING Operations 5Operation No Bevel Ripping Dadoing MOLDING/SANDINGYoke Lock Handle Adjustment Adjustments to compensate for wearAdjusting Bevel Lock Lever To ReadjustAdjusting Carriage Bearings ARM to ColumnWheel Reinstall parts that have been removedLock RodLooseness between column tube and column Trouble-shootingSource Before Trouble Shooting Bevel Lock Handle LooseFeed rate too fast. Slow Feed Rate Saw blade heels Dirty tracks. Clean TracksDull blade or warped board Saw Blade has heelProbable Cause Suggested Remedy Maintenance Maintenance and lubricationRecommended Accessories LubricationModel Repair partsParts List for Craftsman 10-INCHRADIAL SAW Description\ \ +.\\ × × Rig $, r Gouj O0oi 13 14 Parts List for Craftsman 10-INCH Radial SAWModel Number 113.19771 RimKey 17 15Key Part 12 63269Bearing113.19771 SAW on LYSAW with Legs Inch Radial SAW