Sears 113.19771 owner manual Table Clamp

Page 20

locations and functions of controls

The versatility of the Radial Saw is due, in part, to its

controls, and these are the keys to its successful operation. Learn to use the controls for all operations before actually

start ng to saw.

A series of six diagrams is located on the top surface of the arm. These designate the controls that must be used in basic

set-ups and operating procedures. You should become familiar with these diagrams and the operating instructions that follow, before operating your saw.

MITER SCALE

INDICATOR2

ARM CONTROL LEVER

BEVEL INDEX' LEVER /

RIP SCALE tNDLCATOP_

SWIVEL

SWITCH

LATCH LEVER

WITH KEY

ARM LOCK

ADJUSTING WHEEL

TABLE CLAMP

<--7

GUARD CLAMP

SCRE'¢V

	RIP	SCALE
	INDICATOR
ELEVATION	CRANK	4
		4
		CARRIAGE
		KNOB
		3
		LOCK
		HANDLE
		7
		ACCESSORY
ANTIKICKBACK,		SHAFT
ADJUSTING WING	SCREW
ANTIKICKBACK
AND SPREADER
	ASSEMBLY	5
	BEVEL INDEX	5
	INDICATOR	BEVEL LOCK
		LEVER

Image 20

Contents Sears SAW onlyFull ONE Year Warranty on Craftsman Radial SAW Know Your Power ToolUSE Recommended Accessories Ground ALL ToolsAdditional safety instructions For radial sawsInstal Lation Minimize Accident PotentialAntikickback With Power RippingReposition PloughingPower Supply Motor SpecificationsElectrical connections SawMotor Safety Protection Electrical ConnectionsConnections should be Made by a Qualified ElectricianWire Sizes Locations and Functions of ControlsContents ToolsContaining the following Items Truss Hd /4-20 Lockwasher, 1/4Lenkwasher, 5/16 External Nut Hex Jam 5/16-18 Nat, Hex 1/2-13Elevate ARM to ITS Maximum Height STIFFENER1Attach Elevation Crank Assembly and alignment Lock ARM Before ProceedingRemove Shipping Screws and Discard Collar, Set aside and out of the wayAlignment Procedure Step ONEAttaching and Leveling Table Mounting Support Channels Arbor Wrench Screw aStep TWO Installation of Front Work TableAdjusting Column Tube in Column Support OHPtArED O HEX WrenchSquaring Blade to RIP Guide Fence Blade Heel Adjustment Step FourStep Five Squaring SAW Blade to Work TableRest Vertical Heel AdjustmentTooth Installingand Adjusting RIP Scale Indicators Step SIXTable Spacer Board KnobInstall Blade Guard Fence LocationsTable Clamp Power Switch and Key Locations and functionsControls Unlock Index R,ELEASEAntikickback Pencil Line for Gauging Required Length Basic saw operationsThis Edge of Board Against Fence for ALL Cutsfence 1ST CUT Requirements for Crosscut Operation No CrosscutRepetitive Crosscutting Operations 1 ThroughOperation No Miter Crosscut Operation No Bevel CrosscutOperation No -- Compound CrosscutRequirements When Ripping Operation No -- OUT-RIPPINGIN-RIPPING Operations 5Operation No Bevel Ripping Dadoing MOLDING/SANDINGAdjustments to compensate for wear Adjusting Bevel Lock LeverYoke Lock Handle Adjustment To ReadjustAdjusting Carriage Bearings ARM to ColumnReinstall parts that have been removed LockWheel RodTrouble-shooting Source Before Trouble ShootingLooseness between column tube and column Bevel Lock Handle LooseDirty tracks. Clean Tracks Dull blade or warped boardFeed rate too fast. Slow Feed Rate Saw blade heels Saw Blade has heelProbable Cause Suggested Remedy Maintenance and lubrication Recommended AccessoriesMaintenance LubricationRepair parts Parts List for Craftsman 10-INCHRADIAL SAWModel Description\ \ +.\\ × × Rig $, r Gouj O0oi Parts List for Craftsman 10-INCH Radial SAW Model Number 113.1977113 14 Rim17 15 Key PartKey 12 63269BearingSAW on LY SAW with Legs113.19771 Inch Radial SAW

locations and functions of controls

TABLE CLAMP

KNOB