Sears 113.19771 Trouble-shooting, Source Before Trouble Shooting, Bevel Lock Handle Loose

Page 31

trouble-shooting

WARNING: REMOVE POWER CORD FROM POWER

SOURCE BEFORE TROUBLE SHOOTING.

NOTE: Changing one adjustment will effect another, so it is

best to perform all of the alignment procedures when

i

correcting any one problem.

The usual operating "troubles" are listed in the following

paragraphs with the necessary corrections listed.

RADIAL SAW DOES NOT MAKE ACCURATE 0°or 45 ° MITER CROSSCUTS.

a. Looseness between column tube and column

support.

Align as described in Alignment Procedure Section Step Two.

b. Crosscut travel not properly adjusted.

Refer to Step Three in Alignment Procedure Section Squaring Crosscut Travel.

c.Column is Loose in Support.

Refer to Step Two in Alignment Procedure. d. Arm Not Indexing Properly.

Refer to Arm Index Rod Adjustment in

Adjustments to Compensate for Wear section. e. Carriage Assembly Loose on Arm.

Refer to Carriage Bearing Adjustment in adjustment to Compensate for Wear Sections.

f.Looseness between Yoke and Carriage Assembly.

Refer to "Yoke Lock Handle" adjustment in

adjustment to Compensate for Wear Section,

FINISH CUT END SQUARE FINISH CUT END SQUARE

" !

/

 

, .

o_

FENCE FDGE

FENCE EDGE

FINISH CUT LOOKS LIKE THIS - 0 ° CROSSCUT

_,,,,,-!,_,rl,r-]-i,i._.l,l,r

I

I

I

[I

_lj,i,

I

OR LIKE THIS--45° MITER.

g.Sawdust between Work Piece and Fence, Keep Front Work Table Clean.

h.Rip Fence Not Straight. Replace Fence.

2.SAW CUTS AT ANGLE - NOT 90 ° TO TABLE TOP.

a.Table support channels not properly leveled.

Refer to Step One under Alignment Procedure Section.

b.Blade not square to work table top.

Refer to Step Four in Alignment Procedure Section.

3.BLADE ANGLE (BEVEL) CUTS NOT ACCURATE.

a.Corrective Action is the same as paragraph 2A and B above.

b.Carriage Bearings Loose.

Refer to adjusting carriage bearing in adjustments to compensate for wear section.

4.SAW KERF (CUT EDGE) OF STOCK ROUGH - TOOTH MARKS LEFT ON EDGE OF SAW KERF.

NOTE : This condition is commonly called "HEEL".

a. Crosscutting or Miter Cutting

"Heeling" will tend to slide the workpiece along the guide fence, as the cut is being made, and make a square cut almost impossible.

Refer to step 5 under Alignment Procedure Section

-"Squaring Blade to Fence."

F

_hOUL[ 6E 90 c _L_

BOARD

SQUARE

1J

Bevel Lock Handle Loose.

Refer to Adjustment Bevel Lock Handle in

Adjustment to Compensate for Wear Section.

'

'

FENCE

J

 

 

b.

c.

Bevel Crosscutting

Or Bevel Ripping.

 

 

 

 

Refer

to Step

5

Under Alignment

Procedure Section

..............

DIRECTION

OF

DIRECTION OF

Vertical

Heel

Adjusting.

 

 

ATTEMPI

ED

 

 

BLADE TRAVEL

 

 

 

 

 

 

 

 

Using Improper Blade for Finish Cut Desired.

BLADE TRAVEL

 

Use Proper Smooth Cutting Blade.

 

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents SAW only SearsGround ALL Tools Full ONE Year Warranty on Craftsman Radial SAWKnow Your Power Tool USE Recommended AccessoriesMinimize Accident Potential Additional safety instructionsFor radial saws Instal LationPloughing Antikickback With PowerRipping RepositionSaw Power SupplyMotor Specifications Electrical connectionsQualified Electrician Motor Safety ProtectionElectrical Connections Connections should be Made by aLocations and Functions of Controls Wire SizesTools ContentsNut Hex Jam 5/16-18 Nat, Hex 1/2-13 Containing the following ItemsTruss Hd /4-20 Lockwasher, 1/4 Lenkwasher, 5/16 ExternalAttach Elevation Crank STIFFENER1Elevate ARM to ITS Maximum Height Collar, Set aside and out of the way Assembly and alignmentLock ARM Before Proceeding Remove Shipping Screws and DiscardArbor Wrench Screw a Alignment ProcedureStep ONE Attaching and Leveling Table Mounting Support ChannelsAdjusting Column Tube in Column Support Installation of Front Work TableStep TWO OHPtArED O Wrench HEXSquaring SAW Blade to Work Table Squaring Blade to RIP Guide Fence Blade Heel AdjustmentStep Four Step FiveTooth Vertical Heel AdjustmentRest Knob Installingand Adjusting RIP Scale IndicatorsStep SIX Table Spacer BoardFence Locations Install Blade GuardTable Clamp Unlock Index R,ELEASE Power Switch and KeyLocations and functions ControlsAntikickback This Edge of Board Against Fence for ALL Cutsfence 1ST CUT Basic saw operationsPencil Line for Gauging Required Length Operations 1 Through Requirements for CrosscutOperation No Crosscut Repetitive CrosscuttingCrosscut Operation No Miter CrosscutOperation No Bevel Crosscut Operation No -- CompoundOperations 5 Requirements When RippingOperation No -- OUT-RIPPING IN-RIPPINGDadoing MOLDING/SANDING Operation No Bevel RippingTo Readjust Adjustments to compensate for wearAdjusting Bevel Lock Lever Yoke Lock Handle AdjustmentARM to Column Adjusting Carriage BearingsRod Reinstall parts that have been removedLock WheelBevel Lock Handle Loose Trouble-shootingSource Before Trouble Shooting Looseness between column tube and columnSaw Blade has heel Dirty tracks. Clean TracksDull blade or warped board Feed rate too fast. Slow Feed Rate Saw blade heelsProbable Cause Suggested Remedy Lubrication Maintenance and lubricationRecommended Accessories MaintenanceDescription Repair partsParts List for Craftsman 10-INCHRADIAL SAW Model\ \ +.\\ × × Rig $, r Gouj O0oi Rim Parts List for Craftsman 10-INCH Radial SAWModel Number 113.19771 13 1412 63269Bearing 17 15Key Part KeyInch Radial SAW SAW on LYSAW with Legs 113.19771
Top Page Image Contents